Friction Testers
See Also: Tribometers
-
Product
Leak Testers
-
Uson provides automatic non-destructive air leak and flow measurement equipment and solutions used in product development and manufacturing environments for medical device, automotive, electric vehicle battery, packaging and industrial applications. Uson leak testers are highly configurable and are built with premium components ensuring maximum quality, reliability and performance.
-
Product
Macro Hardness Testers
-
Macro hardness is the measurement of the hardness of materials tested with high applied loads.
-
Product
Cable + Network Tester
LinkIQ
-
The LinkIQ™ Network+Cable Tester is designed to provide trusted cable testing along with network testing professionals need to do their jobs. LinkIQ™ validates cable performance (up to 10 Gig) using frequency-based measurements and provides distance to fault information along with a wire map of the cable under test.
-
Product
Hydrostatic Head Tester
-
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester is used for measures the resistance of a fabric to the penetration of water under hydrostatic pressure. Hydrostatic Head Tester complies with AATCC 127, EN 20811, ISO 1420A, etc. Please contact us for Hydrostatic head test procedure.
-
Product
Battery Testers
-
Shenzhen Leagend Optoelectronics Co., Ltd.
leagend battery testers cover 6V battery testers, 12V battery testers, 24V battery testers, 12V electrical system testers, 12V lead-acid battery testers, 24V lead-acid battery testers, LiFePO4 battery testers, stop-start battery testers and more.
-
Product
Digital LOOP/PSC Tester
8025 LP
-
Standard Electric Works Co., Ltd
● Battery is not used.● 3 ½ digit LCD (2000-count).● Backlight function.● 15mA loop measurement which will not trip ELCBs.● Convenient and easier for users to measure the loop impedance directly without bypassing the wires.● Wiring check function.● Over temperature protection.● Over voltage protection.● Built-in voltmeter.● Built-in earth tester.● Built-in loop/psc tester.● Safety standard : EN 61010-1 CAT III 300V EN 61326-1
-
Product
Electrical Installation Testers
-
Continuity tester for measuring the resistance of the protective earth conductors and earth bonds – an ohmmeter dedicated to electrical safety
-
Product
Elongation Tester
SC-5
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.3-2008Used to test elongation (ductility) of copper wires covered with φ0.100-3.0 mmenamel, silk or other insulation materials and other metal wires with tensile strength ≤2000N;Application of SCM control allows for fast operation and strong anti-interference capacity;Preset elongation of samples with two-digit toggle switch and, when the preset value is reached during test, motor and counter would automatically stop action and display results;The instrument is capable of measuring elongation while also the tensile force and holding the maximum tensile force value during stretching;Clamps are designed according to characteristics of various wires to prevent samples from breaking at clamp jaws, easy to load samples and, after samples are compressed, enamel can be automatically broken;While sample is broken, movable clamp would automatically stop moving, with error between displayed and actual elongation value less than 1%;
-
Product
Noise & Vibration Tester
-
System PC Based particularly suitable for vibration and noise measurements for the characterization of mechanical, electromechanical and electroacoustic and for the control and monitoring of installations of production. Complete configurability for the use of platforms PC (Notebook, desktop, PXI) suitable to applications of both static labotatorio, both dynamic (eg road-test) and also in the production line (functional tests and monitoring).
-
Product
Yarn Count Tester
TY361
-
TESTEX Testing Equipment Systems Ltd.
Yarn Count Tester, automatically calculates count systems used for sliver, roving and yarn, and can also be used for fabric yield. Yarn Count Tester consists of an accurate electronic balance and built-in calculating program.
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
Flame Burning Tester
DRK3024A
-
Shandong Drick Instruments Co., Ltd.
It is used to detect high temperature resistance, combustibility and combustion performance of materials.
-
Product
Sulphur Content Testers
-
X-ray fluorescence sulfur in oil analyzer, dark petroleum products sulphur content tester (tubular oven method)
-
Product
Anaerobic Jar Tester
LD-LAJ-A12
-
Anaerobic JarLD-LAJ-A12with 3.5 L capacity has PMMA transparent, smooth surface jar design. High quality O-ring is used to make tight sealing between jar and lid. Adopted with quick snap-shut coupling, enables quick connection to the system in a one soft move. The number of gas packs needed may vary in brands and pack size, required to create anaerobic condition in the jar.
-
Product
Voltage Tester
EW005
-
Wenzhou Zhengyuan Electronic Co., Ltd.
Live and neutral wire identification
-
Product
Martindale Abrasion Tester
SG-P02M
-
This machine is ideal for determining the abrasion resistance of upper, lining, socking, and similar types of shoe materials, particularly those made of fabric. The specimens are capably tested for four bieces or six pieces(option) per time and are rubbed over the abrasive in all directions in a complex, repetitive pattern(a lissajous figure) and, at the same time, the holer totates.
-
Product
RF Signal Testers
-
RF Signal Generators, Record & Playback Systems, Players, Productivity Tools and More
-
Product
Drivetrain Tester
G5.DT
-
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
Product
Earth/Ground Resistance Tester
DE-5030
-
Earth resistance range0~12 / 0~120 / 0~1200 Normal operation conditionsBattery voltagein range of "BATT.GOOD" Earth voltage measurementmax. AC 30V Output current3mA Response timewithin 1 sec. Insulation resistancemin. 100M / DC1000V between input terminals and case Withstand voltageAC3700V (50 / 60Hz) for 1 min. between input terminals and case Battery Check Battery1.5V x 4 Safety standardIEC 61010-1 CAT.III 300V IEC 61557, IEC61010-031
-
Product
Insulation Tester
1555
-
The Fluke 1555 insulation resistance tester offers digital insulation testing up to 10 kV, making it ideal for testing high voltage equipment including switchgear, motors, generators and cables.
-
Product
Flash Point Tester
-
Weshine Electric Manufacturing Co., Ltd
Closed flash point tester, when the test sample is used in a closed environment (such as transformer oil), to determine the closed flash point value of petroleum products. Use touch screen instead of keyboard operation, adopt foreign advanced technology, large LCD screen LCD full Chinese display man-machine dialogue interface, full screen touch key prompt input, convenient and fast, open, fuzzy control integrated software, modular structure, in line with national standards, the United States, EU and other standards.
-
Product
Battery Conductance Tester
BT-3918
-
Kongter Test & Measurement Co., Limited
The excellent performance of BT-3918 battery conductance tester will help you pick out the weak batteries and ensure battery performance in short time measurement. This test of battery internal resistance or battery conductance is essential for stationary batteries. It is also recommended by latest regulation of IEEE 450, IEEE 1188 and IEEE 1106.
-
-
Product
Compression Testers
-
Compression testing is a mechanical procedure for determining how a test sample will react to a force being applied across one side of the test sample.
-
Product
Oil Tan Delta Tester / Tester System
-
The instrument is designed to test the insulation resistance of electronic and electrical components in the range of 1 Meg ohm to 10 Million Meg ohm.
-
Product
Tensile Strength Tester
-
Capacity of Tester with accuracy of 100g : 250 Kgf. and 500 Kgf.Capacity of Tester with accuracy of 10g : 20 Kgf, 50 Kgf and 100 KgfS Type Load Cell fixed with Top GripTraverse Speed: 300 & 100mm /min.Grip Separation: 1000 mmGrip Separation: 25 mmTop Grip is fixed and Bottom Grip is Movable Type.Elongation measurement by Steel Scale and Digital Counter Meter Both.Digital Display of Load and Elongation.Peak value of last test can be read.User friendly key panel with switch of zero setting and peak value of last testMotor: 1/2 HP single phase 220V 50 Hz. ( for Capacity up to 100 Kgf )Motor: 1 HP single phase 220 V 50 Hz ( for Capacity up to 500 Kgf)Power: 220 V AC 50 Hz.Safety device by limit switch to protect from over traverse.
-
Product
Combination Board Tester
ATE QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
Product
SOC Battery Tester
-
This sophisticated battery test equipment allows the battery tester to exercise and explore the battery’s internal profile and produce a true state of charge revealing the batteries true AHR capacity and ability to perform under load.
-
Product
Installation Tester
M75
-
Installation tester for safety tests according to IEC/EN61557-1 with TRMS multimeter functions and test of cable mapping on lan RJ-45 networks
-
Product
Insulation Tester Calibrator
M191
-
High resistance calibrator for insulation testers up to 10 kV. Other insulation related functions include HV capacitance, short current, dielectric and polarization parameters and timer test.
