Friction Testers
See Also: Tribometers
-
product
Fuel Injection Tester
FIT13A
This basic fuel injection tester includes large and small Schrader adapters, M6-1.00 O-ring adapter, and tee manifold. Includes everything necessary to test the following systems: American Motors; Bosch AFC, MPC European and Japanese (except CIS- use our FIT447); Chrysler Corporation; Ford Motor Company; GM (except TBI- use our FIT446); Japanese fuel injection systems; a The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
product
Robotic ESD Tester
SmartZap
The SmartZap is a fully automated zap gun tester with automatic failure detection capability, providing far superior performance than manual zap gun test. It is complying IEC61000-4-2 test standard.
-
product
MU Cable Tester System
16814
The MU Locomotive Trainline/Cable Test System (MU Test System) can perform shorts testing, continuity testing, and ground-leakage testing on each of the 27 pin Multi-Unit Trainlines normally found on Freight Locomotives. The MU Test System is comprised of two identical tester units. Each unit is installed in a rugged, water resistant Pelican case. Each unit contains an MU cable receptacle that mates with a 27 pin MU jumper cable. A snap-on vinyl pouch on the outside cover of each unit provides storage for the battery charger/power adapter and the chassis test lead. The enclosure cover hinges separate from the test unit as the cover is opened; this removes the cover completely to allow free access to the MU cable receptacle and the control panel.
-
product
Film Permeability Tester
Film Permeability Tester is designed to test the permeability of a wide range of packaging materials such as plastic film, composite film, aluminum foil, thin sheets, rubber, porcelain, medical patch, etc.
-
product
Rockwell Hardness Tester
The most popular and widely used method of Hardness Testing, The Qualitest range of Rockwell Hardness Tester Range start from low cost analog models up to sophisticated and advanced load-cell type models. The popular, HardRocker, QualiRock, Rocky series hardness tester models have configurations suitable for Regular and/or Superficial Rockwell Hardness Testing, while our advanced Universal Hardness Tester Range can test the full Rockwell scale in addition to Brinell & Vickers. Qualitest also offers Automatic In-line hardness testers for high volume testing.
-
product
Dry Arc Resistance Tester
Dry Arc Resistance Tester is designed to conduct high voltage,low current Arc Resistance test on solid electrical insulation material as per:ASTM standard D495-99 (2004) and UL 746A. Why Arc Resistance Test? Many Cases of insulator failure are due to deterioration of its surface because of sustained electrical discharge or Arc. This test method is intended to test the resistance of insulating material when a high -Voltage low -current Arc close to the surface of insulation, intending to form a conducting path therein or in causing the material to become conducting due to decomposition and erosion.AdvantagesThis Test ensures that your products meet high standards of quality & safety. This product is meant for all Switchgears/ insulator/ Polymer/ electro plastic manufacturers and manufacturers who use insulators in their products e.g. Wiring Accessories, Appliances, HT/LT line insulators etc.
-
product
Digital Earth Resistance Tester
8PK-ST1520
Capable of measuring earth voltage (Vac.) 2mA measuring current permits earth resistance to test without tripping earth leakage current breakers in the circuit. Battery operated. Auto power off function. Data hold function. Small and light weight.
-
product
AC/DC/IR Hipot Tester
TH9310
Changzhou Tonghui Electronic Co., Ltd.
TH9310A AC/DC withstanding voltage & insulation tester is a kind of small power Hipot Tester. Due to simple and compact structure, mature technique, brand new structure and operating interface, the operation becomes more convenient, and more practical functions are included as well. TH9310A can be widely applied in transformer, device, component especially for winding safety inspection.Withstanding voltage test
-
product
Module Breakage Tester
King Design Industrial Co., Ltd.
1. Destruction System Hardware: *est rack system: support, shielding cover, crane & fixed wall. *Hit bag: FRP bag; 45kg of No.7.5 lead pills; hook, sleeve and hoisting ring. *Attachment: electronic scale, stopwatch, digital caliper
-
product
12-48V Digital Display Circuit Tester
1674A
Peaceful Thriving Enterprise Co Ltd
Check on 12, 24 and 48V systems.
-
product
Bennewart Flex Tester
UI-FT26
Bennewart Flex Tester, also named as Whole Shoe Sole Flexing Tester, is used to test outsole flexing resistance. The whole shoe sole flexing tester is intended to know the effect of sole materials and surface patterns on cut growth by flex sample in 90°as per ISO 20344, ISO 17707, DIN 53543 and etc.
-
product
Voltage & Continuity Tester
Heavy Duty Solenoid Voltage & Continuity Tester - LCD Live Wire and Stud Detector for carpenters and electricians.
-
product
AC High Voltage Breakdown Tester
CIE / 5050A
Cambridge Instruments & Engineering Co.
'CIE' A.C. High Voltage Breakdown Test Set is ideal for fast accurate & reliable testing of withstand/Breakdown test of electrical & electronic materials, components, equipments, panel boards, etc.
-
product
IEC60529 IPX1/2 Rain Resistance Tester
IPX12A-600
Shenzhen Chuangxin Instruments Co., Ltd.
The IEC60529 IPX1/2 Rain Resistance Tester is designed according to the <> of IEC60529 standard, GB7000.1 and GB4208-2008. IEC60529 IPX1/2 Rain Resistance Tester is mainly used to simulate the product under the condition of the rain climate to test the products’ physical properties.
-
product
Horizontal Dedicated Friction Peel Tear Tester
FPT-H1
The FPT-H1 is a dedicated horizontal tester, designed for testing to all the key industry and international standards for coefficient of friction, and for appropriate horizontal peel and tear methods. Its sleek contemporary styling incorporates ease of use and maintenance. Built to exacting standards, yet affordable, the FPT-H1 provides the most accurate and detailed measurement, with guaranteed repeatability in testing. It is ideally suited for the packaging industry, for manufacturers, converters and users of paper, board and plastic films, plus coatings, floor coverings and textiles.
-
product
Phase Squence Tester
Measurement Range3 phase check for AC 90V ~ AC 600V (Sine Wave) Operation Frequency45Hz ~ 70Hz Test Time LimitationAC 110V(continuous)AC 220V(3 hours)AC 480V(12 minutes)AC 600V(3 minutes) Power Supplyno battery required Color change LED phase direction indication
-
product
PC Controlled Low Voltage Tester
Cablescan S9
The Cablescan S9, with a 9-board Expansion Cabinet, may be ordered with 1 to 9 low-voltage 128-point scanner boards. Fully loaded with scanner boards, this tester provides 1152 test points.
-
product
Exhaust Back Pressure Tester
33600
Use to test for clogged or obstructed catalytic converters and mufflers. Fast and easy to use - threads into Oxygen Sensor Port. Includes 12mm and 18mm adapters to fit most domestic and imported vehicles. Gage measures 2 1/2" diameter and has dual scale: 15 PSI and 1.00 Kg/Cm2. Hose is 41" long.
-
product
VDV & USB Cable Tester
PK-2016/2016R
The VDV & USB cable tester is designed for testing today’s media computer networks which combination of telephone USOC (voice), twisted pair (data) and coax security / alarm (video) as well as PC-USB 2.0 3.0 cables.
-
product
Rope Testers
The LMA Signal measures loss of metallic cross-sectional area (LMA) caused by corrosion, abrasion, etc. The LMA Signal is quantitative and can be calibrated. (Typically, a rope must be retired when the LMA exceeds 10%).The WRR Signal measures wire rope roughness (WRR). WRR is defined as the aggregate surface roughness of all wires in a rope. WRR is typically caused by and indicates internal and external corrosion pitting, broken wires and clusters of broken wires. The WRR signal is quantitative, and it is calibrated together with the LMA Signal.The LF Signal can indicate localized flaws (LF), for example, broken wires, corrosion pitting, etc. Because it is only qualitative - and cannot be calibrated - it is of limited value for assessing rope deterioration and for making rope retirement decisions.
-
product
Hipot Testers
V7X Series
With color touch LCD & high speed DSP technology, the compact & rugged V7X sets the standard for price/performance ratio. Made in the USA to meet tough UL, CSA, TUV and IEC Hipot requirements – the V7X provides unbeatable speed, accuracy, user safety and reliability.
-
product
12 VOLT CIGARETTE SOCKET TESTER
MDPPTSTCIG
*Provides the user with a simple way to test a 12V cigarette socket on a vehicle*Mini probe will light up when 10.8V - 15.4V is detected
-
product
IC Tester
The Peritec adopted the NI products, to build in 1/10 the cost of the commercial product functions of the IC tester. It offers original brand as "ECOIC".IC tester on the market, yet very expensive that several tens of million, part of its function could only really used. Therefore, it possible to continue to build the only really necessary function in Peritec, we have created a mechanism to be completed at a lower cost and development, high-performance, short-term.
-
product
Bi-Directional Digital Hydraulic Testers
DHT302, DHT402 Series
The most popular sizes of digital hydraulic tester. Measure flow, pressure, temperature & speed. Flows up to 400 lpm (100 US gpm).
-
product
Semiconductor Large Range Type Tester
HS-PSTT
HS-PSTT large Range Type Tester is a high-grade semiconductor material Type testing equipment,has the feature that testing large range,special suitable for testing the high-Resistivity Silicon Material(contains Silicon Core, phosphorus stick, Boron stick and so on),the resistivity require range is 0.0001～19999Ω·cm, Covers all measurement requirements of various silicon material type testing at the semiconductor and solar energy level at present .
-
product
Surface Roughness Gauges & Testers
Surface roughness gauges are used for measuring the surface roughness of a material. GAOTek’s surface roughness gauges are reliable, high quality, and affordable instruments that provide an accurate measurement. They are an efficient and quick means for inspection or testing. Our gauges are compact, easy to carry and portable, allowing the user to work in complex conditions, and are available for sale to the United States, Canada and globally.
-
product
Energized Distribution Insulator Tester
A sensitive voltmeter, the tester measures the difference in potential across each insulator in a suspect string. Comparative readings from satisfactory strings in the same operating situation quickly indicate the state of every insulator in the string being tested.
-
product
Power Tester
PS-200
It is important to keep your graphic cards powered, but you want to make sure that your graphic cards aren’t overpowered. Not all power supply units have power surge protection, so your graphic cards may be vulnerable to damages from over voltage or over current. Protect your graphic cards now with the new PS-200.
-
product
Akron Abrasion Tester
UI-FT45
Akron Abrasion Tester is used to test rubber abrasion resistance and it is suitable for rubbers with a hardsness in the range of 55-85IRHDx.
-
product
Digital Surge Tester
5KV & 6KV
The Digital Surge Tester is designed specifically to test the coils and windings of Low range AC Rotating machines ranging up to 660 V. The Surge Tester has an Embedded Industrial PC with 8 inch Touch screen Display and software to Store, Recall and Print the Test Reports.
