-
Product
8-Channel 250 MHz A/D with Virtex UltraScale+ HBM FPGA - SOSA Aligned 3U VPX
Model 5585
-
- Jade 5585 and 5586 FAQ- Complete radar and software radio interface- Wideband data acquisition- Multi-channel, multi-board synchronization for high channel count systems- High-bandwidth memory, FPGA logic and DSP density make this board a single-slot 3U VPX processing powerhouse- Exceptional dynamic range and analog signal integrity- Features Xilinx Virtex UltraScale+ HBM FPGAs- Eight 250MHz 16-bit A/Ds- 10 GigE Interface- 40 GigE Interface- Dual 100 GigE UDP interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Compatible with several VITA standards including: VITA 46, VITA 48.11, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Navigation Design Suite for software and custom IP development
-
Product
DDR4 Pro 288-Pin DIMM Adapter
INN-8686-18-PRO
-
Your best option if you need to test a large volume of memory! The RAMCHECK LX DDR4 Pro 288-pin DIMM Adapter (p/n INN-8686-18-PRO) gives RAMCHECK LX users the power to test 288-pin DDR4 modules, including unbuffered (UDIMM), load-reduced (LR-DIMM) and registered modules (RDIMM), both ECC and non-ECC, that comply with JEDEC standards. It includes the DDR4 Series adapter and DDR4 Pro DIMM test head.
-
Product
VHF/UHF Digital RF WATT/VSWR Meter
PMR 3030
-
The PMR 3030 EXT Power Meter is a very versatile instrument covering communication bands from 30-1000 MHz. (The PMR 3030 is available for 30-500 MHz only. The PMR Power Meter is capable of measuring forward and reflected power in the range of a few milliwatts up to 500 Watts. The internal operating system controls measurement, display and the I/Os allowing serial communication to PC, USB to memory stick and USB Serial communication. The I/O options are used to write plots to either memory sticks or to a connected PC, the I/Os can also be used to operate the instrument, giving commands and receiving data. For documentation reference the instrument has a real time clock. Multilayer menus are used to setup and control the operation of parameters.
-
Product
Compact PCI Bus Analyzer / Exerciser
CPCI650
-
The CPCI650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
Digital Accelerometer
ZET 7151
-
The characteristics of the primary transducer are set in the device memory and measurements are performed based on those parameters. Thus, the digital sensors releases the user from setting the measuring channels and data processing. The sensors are fixed on the measurement object while the information transmission units are mounted in electric cabinets. An advantage of the ZETSENSOR units is easy installation and uninstallation as well as indication of feed and signal transmission which, in its turn, facilitates diagnostics of the system at the facility.
-
Product
Thermo-Hygrometer
S3541
-
Data logger is designed for record of temperature and humidity. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper communication adapter.
-
Product
PCIe LVDS Digital Waveform Acquisition - 720 MBit/s Internal Sampling Rate Timing, 700 MBit/s External State Clock
M4I.7735-X8
Digital Waveform
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
Product
PXIe High-Speed Digitizer/ Wideband Digital Receiver, 12-bit, 3.2 GS/s, FPGA Signal Processing
M9203A
Digitizer
The Keysight M9203A is a low noise, 12-bit PXIe high-speed digitizer/ wideband digital receiver with programmable on-board processing. With a wide analog bandwidth, this high-speed digitizer is ideal for applications requiring wideband signal capture and very high dynamic range. The M9203A is a dual-slot 3U PXIe 12-bit wideband digital receiver running at 3.2 GS/s, up to 2 GHz instantaneous analog bandwidth and providing a large 4 GB DDR3 acquisition memory. The M9203A features a large XilinxFPGA that can implement different functionalities depending on the selected firmware option. Dedicated functions can also be implemented on board, allowing support of various applications. Furthermore, Keysight is supporting the deployment of custom processing algorithm on this digitizer with the U5340A FPGA development kit. Integrating algorithms minimizes the need for additional circuitry and exploit the full density and speed of the digitizer.
-
Product
Mixed Signal Oscilloscope 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014G
Oscilloscope
The MSOX3014G 100 MHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Infiniium V-Series Oscilloscope: 25 GHz, 4 Analog Channels
DSAV254A
Oscilloscope
25 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.73 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
CPU RightMark
CPU RM
-
The CPU RightMark suite is meant for objective measurement of performance of modern and future processors in different computational tasks such as numerical modeling of physical processes and solving of 3D graphic problems. It focuses on testing the loaded FPU/SIMD units and the CPU/RAM tandem. As a result, we get pure CPU performance, an objective parameter obtained without the influence of other subsystems, like video and disc systems, except the memory one. It allows us to compare the true performance of different processors irrespective of a type of other system components. It's obtained by dealing only with the CPU and measuring the CPU time spent for execution of computational tasks.
-
Product
T3AWG6K Series – 2, 4 and 8 Channel Arbitrary Waveform Generator
T3AWG6K Series
Arbitrary Waveform Generator
The T3AWG6K series consists of three high-performance arbitrary waveform generators with 2, 4 and 8 analog channels, 16-bit vertical resolution, sampling rate up to 12.32 GS/s with RF mode, waveform memory depth of 4 Gpts, with outstanding signal fidelity and easy generation of complex signals. In addition, up to 32 digital channels in sync with analog signals for advanced electronic testing.
-
Product
PCI Digital IO Board
-
*Bus Interface: PCI Bus*Counter/Timer: 16 Channels*Counter Size: 32 bit*Max. Source Frequency: 80MHz*Compatibility: 5 V TTL/CMOS*Discrete Inputs: 24 Channels*Discrete Outputs: 24 Channels*Pulse Generation: 12 Channels*Bi directional I/O's: 8 Channels*Oscillator stability: 50 ppm*Op-to isolation for I/O's*DMA buffered operation*16-bit data bus 32 bit Address bus for External Memory Interface*The Pulse Width and PRI of the pulses can be varied*The pulse generation frequency from 10Hz to 40MHz (25ns to 100msec)*The no. of pulses controlled from 1 to 255 pulses*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Personal Gamma Radiation Dosimeter
EcotestCARD
-
The radiation monitoring badge EcotestCARD allows storing dose accumulation history with real time reference in the non-volatile memory, and communicating it to the computer. If the programmed threshold levels of gamma dose or its rate are exceeded, light and audio alarms are actuated.
-
Product
Isolation Measurement System
DM-8000H
-
*The input block, control block and display block are isolated with optical fiber cables. (DM-900A/AL, DM-910A/AL)*Frequency bandwidth: DC to 500MHz.*Simultaneous multi-channel measurement of many channels of different reference potentials. (2 to 24 channels) (DM-900A/AL)*Long-life battery drive. (The system can be driven by three batteries for about 12 hours) (DM-900A/AL, DM-910A/AL)*Measurement using long memory. (DM-900A/AL, DM-910A/AL)*Simultaneous measurements of the inverter's switching waveform and ON-voltage. (DM-910A/AL)
-
Product
SMARC® 2.1 Short Size Module With Intel® Core™ I3 Processors, Intel® Processors N Series And Intel® 7th Gen Atom® X7000E Processors
LEC-ALN
Computer on Module
The ADLINK LEC-ALN is a SMARC module that supports up to 8 cores Intel® Core™ i3 (i3-N305, i3-N300) Processors, Intel® Processors N Series (N97, N50) and Intel® Atom® x7000E (x7425E, x7213E, x7211E) Processors (formerly Alder Lake-N) with integrated Intel® UHD graphics and high-speed interfaces. LEC-ALN modules support up 16GB LPDDR5 memory, up to 256GB eMMC storage (build option) and are also available with rugged operating temperature range and low power envelope, making them a perfect match for mission critical fanless edge computing applications that require safety and reliability at all times.
-
Product
Test & Programming Software
ScanExpress
-
The ScanExpress Family of boundary-scan software offers a fully integrated development environment that includes boundary-scan and at-speed functional test program generation, test program execution with advanced pin level diagnostics, interactive boundary-scan debugging, and in-System Programming (ISP) of devices such as Flash memory, serial EEPROMs, CPLDd, and FPGAs.
-
Product
3.5 Inch SBC with 7th Gen Core i7 CPU and PCIe/104
VENUS
-
Based on the “Kaby Lake” 7th generation Core i7 processor, Venus offers high CPU performance in a small form factor rugged SBC with modest power consumption. It incorporates a full suite of rugged features such as soldered memory, latching connectors, a thicker PCB, and true -40/+85ºC operating temperature, making it suitable for the most demanding vehicle applications. High I/O density, multiple expansion sockets, rugged design, modest power consumption of 14W, and wide temperature operation combine to make Venus an extremely attractive option for applications requiring high CPU performance or ruggedness.
-
Product
SD Card V.4.1 & UHS-II PHY
SD 4.1 Total Solution
-
To meet the ever increasing data transfer rate in high end applications, such as professional broadcasting transmission or advanced high resolution display, the SD 4.1 specification calls out the maximum performance of 1.56 Gbps at UHS-II full duplex mode per lane or half duplex UHS-II at 3.16 Gbps. In real applications, due to the system overhead and different SD 4.1 device controller designs, the actual measured performance can vary dramatically from system to system. With the newly introduced ADMA 3, the OS driver is now able to issue multiple read or multiple write commands at once, without having to wait for the SD controller to complete one command at a time. Once the SD host controller has collected multiple commands, it will then manage and complete them without intervention from the host software drive. Thus, the UHS-II 1.56 Gbps interface can be more effectively utilized and maximize the system throughput. This feature can be very useful when running multithreaded applications where multiple applications are constantly updating their status or swapping their contents by writing or reading small chunk of data to or from the memory card.
-
Product
16 GHz Differential Probe with ProLink Interface
DH16-PL
Interface
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Relay Testers
-
Outputs 100VA single-phase voltage and 180VA single-phase currentEquipped with counter function, output selector, auto sweep function, memory function, DC output for testing, master/slave function, etc.Output frequencies of 50Hz, 60Hz, and 10Hz to 200Hz, using external synchronization or line synchronization (selectable)Equipped with GPIB/RS-232C interfacesWeight: 19.5kg
-
Product
Intelligent Interface Card
IIB-1553-ISA
-
The IIB-1553-ISA is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-ISA supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multilevel triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable.The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
Training Board
JT 2156
-
The JT 2156 training board has been devised to demonstrate all the latest features and test techniques available to users of JTAG Technologies’ ProVision & JTAG Live application development systems. As well as a modern ARM Core processor, the design also includes an Altera Cyclone FPGA, DDR Memory, Ethernet PHY, and several SPI and I2C peripheral parts. The JT2156 is shipped with a comprehensive self-study manual for getting to know the in-depth features of ProVision and/or JTAGLive Studio. For Altium users the design also serves as an example of how to adapt the Nano board into a realistic custom design.
-
Product
Fanless Embedded System With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, 4-CH PoE And MXM 3.1 Type A
eBOX671-521-FL
-
The eBOX671-521-FL is a GPU computing embedded system that comes with 4-CH PoE and MXM 3.1 Type A slot for applications in machine vision, edge computing, traffic vision, deep learning, and artificial intelligence of things. The outstanding eBOX671-521-FL with enhanced GPU computing performance is powered by the 9th/8th gen Intel® Core™ i7/i5/i3 processor with up to six-core, Intel® Pentium® processor, or Intel® Celeron® processor and comes with Intel® Q370 or optional Intel® C246 chipset. The fanless embedded GPU-based system is equipped with dual DDR4 ECC/non-ECC SO-DIMM slots for up to 64GB of system memory. The embedded vision system has an optional MXM type A slot for NVIDIA GTX1030 and GTX1050 graphics modules to enhance the performance of the visual display. Furthermore, this Intel® Coffee Lake-based embedded box PC is specially designed with four Gigabit 802.3at (PoE, Power-over-Ethernet) compliant Ethernet ports with a total power budget of 60W, six USB 3.1 ports and two Gigabit LANs to connect different devices or sensors. It comes in great expansion possibilities, including one internal MXM 3.1 type A connector, two full-size PCI Express Mini Card slots and two SIM slots. For storage, it has two swappable SATA HDD drive bays with a height of up to 9.5 mm and one mSATA for RAID 0 and 1 feature. Besides, we have designed a flexible I/O window slot for incorporating application-oriented I/O functions to meet the requirements of various cases. This embedded vision computer can be mounted using wall or DIN-rail mounting for versatile use in various environments.
-
Product
Pico-ITX SBC With Intel® Atom® Processor E3845/E3827, LVDS/VGA, LAN And Audio
PICO841
-
The PICO841, an extreme compact embedded pico-ITX motherboard, is designed to support the latest 22nm quad cores Intel® Atom® processor E3845 or dual cores E3827 (codename: Bay Trail) with one DDR3L system memory maximum up to 8 GB. With its compact size and ultra-low power consumption, it is perfect for space-limited and power saving environments. Otherwise, the energy-efficient embedded board is built to withstand wide temperature conditions, ranging from -20°C to +70°C (-4°F to +158°F). Integrated with Intel® HD graphic engine, the PICO841 supporting VGA and 18/24-bit dual channel LVDS in dual-view provides faster and better graphic performance. Furthermore, to increase the connectivity and reliability, the rich feature of I/O interfaces are integrated to allow flexible cabling. Coming with two PCI Express Mini Card sockets, the pico-ITX mainboard offers excellent extensibility.
-
Product
Osprey /SXP Co-Processor
9740-S
-
PCI version of the Osprey /SX successor to the Osprey 18B Occupies one PCI slot. A writable control store, FPGA implementation of the PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory.
-
Product
Portable Paperless Recorder
-
5.7” Colour TFT LCD (320 x 240) with Backlight8 Input Temperature Measurement / Logging (ºC/ºF )Colour Graphic Display of 8 Curves at the same timeDigital & Analog (bargraph) Data DisplaySelection of 11 Types of Thermocouple (K, J, E, T, R, S, N,..)Easy Socket for Thermocouple Mini ConnectorBasic Accuracy 0.05 % ± 1ºC (K Type)28 Hours Recording with Lithium Battery of 3400 mAHStatistics Data (Histogram) for easy AnalysisProgrammable Hi-Lo Alarm with TimerDisplay of Max & Min Values for each InputSampling Rate 8 Inputs / 1 SecondHide or Display Selected CurvesStandard 2G SD Memory Card (Stores 3.8 Year of Data)SD Card Directly Read by PCRead & Delete Data files DirectlyBuilt-in Calendar ClockAccept Analog Outputs from InstrumentsScreen Hardcopy for Easy Documentation Ready to Use Package ( Thermocouples, SD Card & Battery)
-
Product
T3DSO4000L-HD Series Oscilloscopes
T3DSO4000L-HD Series
Oscilloscope
The Teledyne Test Tools T3DSO4000L-HD Oscilloscopes feature four and eight channel low profile models all with 12 bits of vertical resolution. With analog bandwidth options of 500 MHz, 1 GHz and 2 GHz. Each model offers a maximum sample rate of 10 GSa/s with ESR per channel, and a maximum memory depth of 500 Mpts in single channel mode. The T3DSO4000L-HD series is ideal for ATE systems as well as other automated applications.
-
Product
High Level Language Debugger and Emulator Tool
Universal Debug Engine
-
Programmierbare Logik & Systeme GmbH
With Universal Debug Engine (UDE®) PLS offers on top solutions for software development of systems-on-silicon including debug support for the 16 Bit and 32 Bit microcontrollers C16x, C166™, ST10F276, ST10F280, XC166, XC2000, XE166, XMC4500, C166S V2, SDA6000, TriCore™ from Infineon and STMicroelectronics, Power Architecture® MPC55xx, MPC560x, MPC563x, MPC57xx from NXP™, PowerPC PPC440SPe from AMCC, Power Architecture® SPC560, SPC563, SP574 from STMicroelectronics, ARM7™, ARM9™, ARM11™, Cortex™-M0, Cortex™-M0+, Cortex™-M3, Cortex™-M4, Cortex™-M7, Cortex™-R4, Cortex™-A8, Cortex™-A9, XScale™, SuperH™ SH-2A derivatives in a new multicore debug environment as well as technical support. The extensive feature list includes functions like: high speed and flexible target access via JTAG, cJTAG with OCDS L1, EmbeddedICE, OnCE, COP, DAP, DAP2, SWD support, OCDS L2 trace, MCDS trace, CoreSight™ trace, ETM trace, ETB trace, Nexus trace, ASC, SSC, 3Pin and CAN, in-system FLASH memory programming of FLASH / OTP with UDE MemTool, support of various RTOS, OSEK® and test automation tools.
-
Product
3U CompactPCI Serial Processor Blade with 6 COres/12 Thread Core i7 and Xeon Processor
MIC-330 Series
Processor Blade
MIC-330 is a 3U CompactPCI® serial processor blade with 6 cores/12 thread Core™ i7 and Xeon® processor and configured with Intel® CM246 PCH to support dual-channel 32GB DDR4-2666, up to 16GB on board memory for rugged applications, and another 16GB are available via the SO-DIMM socket for expansion.
