Electrostatic Discharge Simulators
create known values of electrostatic discharge.
-
Product
Engineering Simulation Services
-
Staying at the forefront of product development requires more than ambitious goals. Engineering teams also need the right expertise, resources, and support to solve complex challenges without slowing innovation.
-
Product
Network Simulator
SWAT WDS
-
Alethea Communications Technologies Pvt Ltd
Alethea’s SWAT WDS Network Simulator emulates the whole Customer Premises side with one box generating up to 32 CPEs with 4 ~ 8 ethernet clients behind each CPE. This setup which mirrors actual field deployment allows transmission points to be checked in detail as soon as the access point is setup. The solution gives a calibrated measure of the User Experience expected over the deployed system.
-
Product
Digital Load Cell Simulator
Model EL41
-
Xiamen Elane Electronics Company, Ltd
Detection and debugging of all kinds of weighing instruments - "must have" for any scale service technician - fully RS232 controllable for testing of electronics for scale installation and manufacturing.
-
Product
Partial Discharge Monitor
INDIPARD
-
INDIPARD, a low-cost measuring device for partial discharge monitoring.
-
Product
Circuit Breaker & Control Cabinet Simulator
SIM-CB6
-
The SIM-CB6 is the circuit breaker simulator that will make you an expert in breaker testing. The SIM-CB6 enables you to simulate any type of circuit breaker (SF6, Air Blast, Oil, etc.) up to 6 contacts (2 contacts per phase), with or without closing/opening resistor contacts and control cabinets. This simulator will allow you to increase your knowledge on circuit breaker analyzer systems to ensure full efficiency once on the field.
-
Product
ESD - Simulator
SESD 230
-
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
Product
Local Loop Simulator 128 Channels
458-CC-16/458-CM
-
FEATURES: Accepts 1 to 16 Line Modules; User-Friendly Interface; Multiple Configurations; Field-Upgradeable Software; One-Year Warranty/Calibration. The 458 Series 16-slot Chassis, which consists of the 458-CC chassis and one of three control modules, provides a wide variety of configurations through use of up to 16 plug-in Line Modules.
-
Product
Solar Simulator
PEC-L15
-
●Light source/lamp house integrated compact design●Irradiation head rotates (downward, upward, sideways irradiation possible)●5cm square optical filter can be attached●Equipped with high-speed shutter (100ms)●Body weight is only 16kg.
-
Product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module
43-670-XYZ-AABBCC
Simulator
The 41/43-670 range is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. Available with up to four banks, each bank is capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
Product
Solar Simulator Continuous Light
-
This type of solar simulator uses Xenon high pressure arc lamps as light source. These lamps have a colour temperature near 5800 K, so it is feasible to filter the light output to an excellent AM 1.5 spectrum. If a tuneability of the spectrum is required, these lamps can be combined with tungsten lamps to achieve multi-source solar simulators. These can be used to measure tandem/triple/multijunction solar cells. They also allow detailed analysis of all types of solar cells using a spectral metric (see : Publication List).
-
Product
Partial Discharge Meter
TMG
-
The partial discharge meter TMG was developed for Partial Discharge tests according to VDE 0434 and IEC 60270.
-
Product
4, 8, 16 Or 32 Channel ARINC429Test And Simulation Modules For XMC
AXC429-x
-
ARINC429 Test and Simulation module for XMC with 4, 8, 16 and 32 programmable Tx/Rx channels plus up to 8 Discrete Inputs/8 Discrete Outputs which can be monitored or generated.
-
Product
2 Port T1/E1/PRI ISDN Simulator PCI
SIM-2PRI-PCI
-
The most inexpensive ISDN PRI simulator on the market. Designed in standard PCI card form factor it has two PRI(T1 or E1) ports allowing ISDN PRI equipment to be connected together just as if they were connected through the ISDN network. Simulator card does not require any OS drivers, completely software independent and it take only power from the host computer.
-
Product
LED Solar Simulator
LumiSun-50
-
The LumiSun-50™ is a high power, multi-wavelength LED solar simulator that meets IEC 60904-9 Class AAA for spectral match, uniformity of irradiance, and temporal stability. The LumiSun-50 achieves a spatially uniform illumination field from a chip-on-board (COB), multiple-wavelength LED die array. The field of illumination is 50 x 50 mm at a working distance of 200 mm. The LumiSun-50 includes a driver/controller which individually provides constant current to each die in the COB array. Total irradiance of 1.1 sun units is provided and can be decreased to 0.1 suns. The LED light source of the LumiSun-50 is contained within an air-cooled housing that can rotate the angular beam alignment. Adjustment and setting of the optimum light path working distance is visually facilitated by a converging pair of red dot laser pointers.
-
Product
2 PRI + 32 BRI-S/T ISDN Simulator
CH-32BRI-ST-MOD-2PRI
-
This unit has two PRI ports and 32 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
SIMulation Workbench
-
A comprehensive framework for developing and executing real-time hardware-in-the-loop and man-in-the-loop simulations.
-
Product
Partial Discharge Test Set Up
-
This testing set is of great use in industries for various testing applications. We strictly follow all the guidelines while manufacturing this Partial Discharge Test Set Up.
-
Product
Incremental Encoder Simulator
ENC-SIM01
-
Plant Control and Automation Pty Ltd
This instrument is designed to simulate the function of most types of incremental encoders; it allows the engineer to fully test a control system that uses a rotary or linear shaft encoder, without the need for any mechanical movement.
-
Product
Partial Discharge Tester
GTPD-4C
-
GTPD-4C partial discharge comprehensive tester is the new generation of digital PD measurement and analysis instrument. The instrument has a strong ability of comprehensive analysis of partial discharge and detection of partial discharge in small signal and strong interference environment. With different accessories, it can measure and locate the partial discharge in any high voltage electrical equipment. It can realize testing the transformer partial discharge by applying the voltage on the three phases simultaneously.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Modular Solar Array Simulator Mainframe, 1200W
E4360A
Mainframe
The Keysight 1200W, E4360A Modular Solar Array Simulator is a 2U high, 2-slot mainframe that accepts up to 2 E4360 series modules. Modules are ordered separately. It offers LAN, USB, and GPIB interfaces standard.
-
Product
Digital And Analog Call Simulation
-
GL’s T1 E1/Analog Test Suite supports analysis and emulation of legacy protocols (MFCR2, E&M, SS1/SS4, SS5, Voice Call Signaling, 2-wire Call, SF Signaling (DTMF)) applicable to Federal Aviation Administration "FAA" within their National Airspace System "NAS" Ground-to-Ground Air Traffic Control Network and Voice System (NVS) to Analog Interphone.
-
Product
ARINC 429 Test And Simulation USB Module
USB-429
-
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Hybrid Vehicle Battery Simulator and Test System
-
Winner of the SAE 2008 Technical Award for Hybrid Vehicle Testing Technology, SAKOR Technologies Hybrid Vehicle Battery Simulator and Test System is designed for simulating high-voltage batteries in an electric drivetrain testing environment as well as directly testing high-voltage batteries and charging systems.
-
Product
LXI Simulation Tool
60-901-001
-
This tool will simulate all of our PXI & LXI switching products and most of our PXI simulation products allowing for code development independent from your application hardware
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PCI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Patient Simulator
-
Fluke Biomedical ProSim Vital Signs Simulators transform physiological simulation by adding multi-parameter functionality (including ECG, SpO2, temperature, respiration, NIBP, IBP, cardiac output, and fetal ECG/IUP) in a single patient simulator device, helping you meet your patient monitoring system testing and medical device quality requirements to ensure patient safety.
-
Product
Radio Link Simulator
RLS-2100
-
Square Peg Communications Inc.
It is the most comprehensive, with unparalleled impairment simulation, real-time multi-satellite orbit calculation, full motion support and integrated GPS simulators. It is the most flexible, providing end-to-end or single link simulation of wideband terrestrial and satellite networks, satellite selection via open standard interfaces, and facilities to enable seamless integration into more complex test beds if required. It supports the highest bandwidth and has an intuitive, user-friendly interface. And it does it all in one box.
-
Product
Simulation Transport Vibration Table
CX-M120
-
Shenzhen Chuangxin Instruments Co., Ltd.
CX-M120 Simulation Transport Vibration Table was applicable to toys,furniture,gifts,cera-mics,packaging and other products to simulate the transport tests.Comply with the U.S. and European transport standards and have characteristic with low noise,reasonable structure,durable,etc.Basic Standard:Following The EN.ANSI.UL.ASTM.ISTA International Trans-port Standard.
