Interoperability Testing
assures functionality between two distinct elements.
See Also: Interoperability Test
-
Product
In-line High-Density ICT System Series 7i
E9988GL
-
The E9988GL Keysight i3070 Series 7i Inline High-Density In-Circuit Test (ICT) system brings industry-leading ICT technologies into your automated manufacturing line, saving resources and optimizing your automated test strategy.
-
Product
Digital Test Instrumentation
EDigital-Series™
-
Teradyne’s eDigital IVI driver controls all parallel digital functional test parameters, including per-pin timing, data formats, pattern data, and timing alignment on 64 channels (32 static + 32 dynamic or 32 differential)—each with an 8M pattern depth and results memory.
-
Product
VR/AR/MR Calibration Platform
-
AR, VR and MR device calibration is critical for product performance. Leverage Averna’s standardized alignment platform to efficiently calibrate cameras and Inertial Measurement Unit (IMU) modules with supreme accuracy. Easily customize or upgrade the base platform into the automated quality solution to best fit your manufacturing requirements.
-
Product
PCI Express 3.0 Test Platform with SMBus Support
-
The Summit Z3-16 Test Platform with SMBus Support allows the Summit Z3-16 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen3, Gen2 or Gen1 hosts and devices. In addition, it supports the Summit Z3-16 with SMBus Support by providing SMBus tapping connectivity.
-
Product
200 Vdc External Voltage Bias Fixture
16065A
-
Measure a DUT with up to +/-200 V DC bias and also measure axial/radial lead components
-
Product
EMI Test System
TS9975
-
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
Imperial Test Executive
ITE
-
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
Product
Functional Test Fixtures
-
Forwessun’s Functional Test Fixtures are tailored to validate the performance of your electronic assemblies, ensuring each product meets critical quality and functional standards. With customisable designs and precision engineering, these fixtures support a range of testing needs—from checking connectivity and function to confirming performance under real-world conditions. Built to handle rigorous demands, Forwessun's solutions are ideal for industries requiring reliable and repeatable results. Whether for high-volume production or specialised testing, our fixtures provide robust, adaptable support to maintain efficiency and accuracy throughout the testing process. We also create, and work with Ingun to create fixtures using the Ingun kit.
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
-
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
-
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
-
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
ESS Performance Test System
-
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
Product
OTP-Based Test System
-
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
Product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
-
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
Product
Test Port Cable, 1 Mm
11500K
-
Connect test ports to devices, fixtures, or probe tips with this 20-cm cable featuring a return loss of 16 dB minimum
-
Product
Universal Test System
LEON System
-
A universal ICT, FCT, ISP and Boundary Scan platform.Based on the ABex platform, which directly integrates Konrad analog bus technology and PXI/PXIe in one chassis, the LEON platform can be configured to solve various test challenges. Due to this architecture only one system provides the complete test flow combining ICT, ISP, Boundary Scan and FCT.Various form factors and configurations allow a perfect combination between cost, speed and test coverage. The modular architecture provides the possibility to reconfigure or upgrade the systems based on your test needs.The LEON System software provides a powerful development and test execution environment which directly supports NI TestStand. All systems and components could be integrated into third party software using supplied APIs.
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
-
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
BMS Manufacturing Test System
-
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
Product
Military Communications Test
-
Astronics testers for military radios and wireless communications systems help you keep your most critical communications up and running smoothly. Write test program sets once and deploy them instantaneously everywhere – whether your test set is in the factory, at the depot, or in operation.
-
Product
SoC/Analog Test System
3650-S2
-
The Chroma 3650-S2 is specifically designed for high-throughput and high-parallel testing to provide the most cost-effective solution for fabless, IDM and testing houses.
-
Product
Advanced SoC/Analog Test System
3650
-
Chroma 3650 is an SoC tester with high throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses.
-
Product
NI Automated Test Software Suite
-
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
-
Product
Test Port Cable, 1 Mm
11500I
-
Connect test ports to devices, fixtures, or probe tips with this 8.8-cm cable featuring a return loss of 17 dB minimum.
-
Product
Modular Functional Testing Platform
OTP2
-
Functional testing is an important part of product development and manufacturing and is used to ensure quality, performance and reliability from launch to end of life. A modern, future-proof functional test system must meet many criteria in order to meet the ever-growing demands of the industry. The OTP 2 open test platform developed by LXinstruments meets the following requirements for a dynamic and highly competitive market.
-
Product
110 GHz, 1.0 Mm (m-f) Test Port Cable 10 Cm
11500JK10
-
Connect test ports to devices, fixtures, or probe tips with this 10-cm cable
-
Product
Automated Test Systems
-
WinSoft designs, develops and integrates automated functional test systems for use in aerospace, military, high tech and commercial applications
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
-
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
Product
PXI Semiconductor/IC Test System
-
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
Product
Digital Test Instruments
-
Conduct pattern-based digital tests incorporating the latest parallel, digital, serial, and bus protocols with the PXIe-6943 digital test instrument.
-
Product
SoC Test System
V93000 SoC / Smart Scale
-
Advantest’s V93000 Smart Scale generation incorporates innovative per-pin testing capabilities. Each pin runs it own sequencer program for maximum flexibility and performance, for example in multisite applications. Full test processor control ensures time synchronization between all card types, like digital, Power, RF, mixed signal and so on. The user benefits are reduced test time, best repeatability and simplified program creation. The system design makes it easy to extend your configuration with new modules and instrumentation, as your test needs change.
