-
product
Installation Testers
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
product
4-Channel 500 MHz A/D and 4-Channel 800 MHz D/A with Virtex-6 FPGA - 6U VPX
Model 58650
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 500 MHz 12-bit A/Ds- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
10 MHz To 54 GHz USB Wide Dynamic Range Peak And Average Power Sensor
U2066XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
SWIR Line-Scan USB3 Cameras
NECTA S Series
NECTA S, the SWIR line-scan model in NECTA camera family, is capable of high-resolution acquisition in short-wave infrared bandwidth, ranging from 950 to 1700 nm. This new SWIR camera can reach up to 40kHz line rate with 14bit A/D converter: its high-speed USB3 interface, an advanced I/O, together with a compact and rugged aluminum case, make NECTA S suitable for most demanding machine vision applications.
-
product
4-Channel 200 MHz A/D with 1532 DDCs, Kintex UltraScale FPGA - 6U VPX
Model 58865
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete software radio receiver solution for extremely high channel-count applications- Uses Xilinx Kintex UltraScale KU035 FPGAs- Four 200 MHz 16-bit A/Ds- Eight wideband DDCs (digital downconverters)- Up to 1524 narrowband DDCs- Sample clock generation and synchronization to an external system reference- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Chassis / System Enclosures
VECTOR Electronics and Technology, Inc.
Vector’s 3D modeling capability and owning our own injection molds, extrusion dies and presses give us more cost effective designs and products. We supply many programs such as institutional, telecom, imaging, military, transport, industrial controls and aerospace.
-
product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 3U VPX
Model 52791
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x4- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Ellipsometer
alpha-SE®
For routine measurements of thin film thickness and refractive index, this ellipsometer allows you to mount a sample, choose the model that matches your film, and press "measure". You have results within seconds. Works with your materials - dielectrics, semiconductors, organics, and more.
-
product
Macro-Vickers Hardness Testing System
LV Series
LECO's LV Series Macro-Vickers Hardness Testing Systems offer an affordable testing system suitable for larger, heavier samples used in welding and other demanding applications. Models include analog and digital, with options to upgrade to automatic configurations.
-
product
Full C-Band or L-Band Tunable Laser Source
LTS-2000
Hangzhou Huatai Optic Tech. Co., Ltd.
The LTS-2000 series full C-Band or L-Band quick adjustable laser optical source , is a 2U small model of high precision and muti-function, can be set up 1~4 port independent C or L band adjustable optical source. Various flexible configurations optional (see more in product series) , and makeing daily test and measurement applications greatly convenient.
-
product
Pressure Transducers with USB Interface
P61
The Validyne model P61 is a digital differential pressure transmitter designed for industrial pressure measurement applications. The on-board microprocessor provides high accuracy and improved stability in changing thermal environments. Communication and power via USB interface provides remote zero and span adjustment as well as digital pressure readings in engineering units. Drivers and software for the USB interface are included.
-
product
Electrochemical Detector
800D
The Model 800C series is designed for electrochemical detection. This instrument can be used for monitoring the current passing through a flow cell in liquid chromatography/electrochemistry and in-flow injection analysis, as well as other electroanalytical applications.
-
product
Low Resistance Or Continuity Testing
From Megger, these highly accurate, easy to operate instruments measure resistance with resolution as fine as 0.1 micro-ohm. Digital micro-ohmeters and DLROs measure contact resistance of switch and circuit breakers, aircraft frame bonds, and rail and pipeline bonds just to name a few of the applications. Megger has models available for testing using test currents from 0.5 mA to 200 amps covering a multitude of applications that require precise low-resistance measurements.
-
product
Reference Meter
SB1300
Shenzhen Star Instrument Co., Ltd.
The SB1300 three-phase multi-function reference meter incorporates 32-bit floating point DSP, wide-range measuring and embedding industrial PC technologies. This model was the first approved by China National Institute of Metrology. Star Instrument has been granted the first manufacturing license for class 0.02 reference meters. Basic measuring range (phase voltage): 1V~480V, current measuring range: 1mA~120A; wide measuring range (phase voltage): 0.1V~1000V, current measuring range: 0.1mA~200A
-
product
PNA Network Analyzers
The PNA Series of network analyzers offers industry-leading performance for testing amplifiers, mixers, and frequency converters. Built-in pulse modulators and pulse generators provide pulsed S-parameter measurements quickly and accurately. All models are available in two-port single-source and four-port dual-source versions.
-
product
1kV, 120 MHz High Voltage Differential Probe Without Tip Accessories and with Auto Zero Disconnect
HVD3106A-NOACC
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
Economy Model Vertisocket™
Series 800 and 822
Thrifty Model Vertisockets with Bifurcated Contacts. These low cost VertisocketsTM are recommended for high volume vertical display mounting applications. Very useful for connection of board-to-board jumpers and for DIP switches as well as LED devices.
-
product
Dimensional Metrology
Nova offers in-line optical integrated and stand-alone metrology platforms. The metrology product portfolio, combined with our modeling algorithm software, delivers unique measurement capabilities for the most advanced semiconductor technology nodes.
-
product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - 6U VPX
Model 57760
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four or eight 200 MHz 16-bit A/Ds- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Sample clock synchronization to an external system reference LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Reverse Engineering Services
The term “reverse engineering” can be a little confusing. It is sometimes used for things like software and electronic circuits. When 3D scanning companies use the term, they are referring to the process of re-creating design drawings by taking measurements and/or scans of the part itself. It is a 2-step process: 1) capture a 3D scan of the object, and 2) Create a 3D CAD model of the object
-
product
ECHO 8 Ultrasonic Corrosion and Precision Thickness Gage
ECHO 8
Danatronics offers our newest ultrasonic precision thickness gage line, the ECHO 8 series. ECHO 8 represents our most advanced thickness gage ever combining dual and single element transducers all in one small package. ECHO 8 offers a 3.5” high resolution sunlight readable color display with live A-Scan, use of a wide variety of dual, contact, delay line and immersion transducers from 1-20 Mhz as default and custom created and stored applications setups, B-Scan, datalogger with up to 32GB of SD card memory and interface to Microsoft excel. The ECHO 8 is available in 4 models including the ECHO 8, ECHO 8DL, ECHO 8W and ECHO 8DLW. The vibrate on alarm feature is the world’s first and is great for loud environments
-
-
product
Fail Safe Waveguide Switches
Waveguide switches enable very rapid switching between two RF channels. Fail Safe Waveguide Switches return to the de-energized position when the power is disconnected and requires a small holding current in the energized position. All models have low VSWR and high power handling capacity. They withstand the full power rating of the waveguide and most models can be pressurized to 0.2 MPa (2 ATO) for high peak power applications.
-
product
Current Probes
XQ13
Beijing GFUVE Electronics Co.,Ltd.
The model XQ13 ac micro amp clamp on current probe is suitable for 10A-100A cable online measurement, it belongs to high performance current sensor field.
-
product
Three Phase AC Voltage Source
EAC-TAVS
Electronic Test & Power Systems
The EAC-TAVS is a series of programmable high power AC voltage sources. Each system provides a three phase true sinewave output as standard. Each unit is built in a freestanding cabinet. The output frequency is adjustable in the range of 45 - 105Hz. Different frequency ranges are optional, with up to 805Hz possible. An RS-232 and CAN interface are provided as standard. The high resolution TFT front panel displays a host of measurement and setting functions. Besides standard models, other nominal power levels and voltages can be user specified. Single phase and bidirectional versions are available on request.
-
product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - QuartzXM
Model 6003
- Unique QuartzXM eXpress Module enables deployment in custom form factors- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- Measuring only 2.5 by 4 inches- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- GTY connections for gigabit serial communication- Ruggedized and conduction-cooled versions available- Includes a complete suite of IP functions and example applications- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products
-
product
Frequency Hopping Spread Spectrum
FHSS
Futaba introduced FHSS (Frequency Hopping Spread Spectrum) systems in 2010, to offer modelers a less expensive way to enjoy 2.4GHz dependability. Other advantages include extremely low latency, exceptionally fast frame rates, transmitters with no external antennas and low-cost receivers with Easy Link convenience.As the name implies, the transmitter signal of an FHSS system literally hops from frequency to frequency in a pseudorandom sequence. The combination of frequency hopping with Futaba's advanced algorithms creates 100% frequency security.
-
product
Front & Backside, Semi-Automatic Mask Aligner
Model 800E
The OAI Model 800E front and backside, semi-automatic mask aligner system offers advanced features and specifications found most often in costly automated production mask aligners. With the development of this mask aligner, OAI meets the growing challenge of the dynamic semiconductor and MEMS market with a new class of mask aligners that are engineered for R&D and low volume production.
-
product
DC Power Supplies
Single, dual or triple output models with power from 30 watts up to 1200 watts. Linear, Mixed-mode or PowerFlex regulation. Remote control models with variants of Analog, USB, RS232, GPIB and LAN interfaces.
-
product
Sound Level Meter
831-LOWN
Easily make low noise measurements to 6.5 dB A-weighted using the Model 831-LOWN sound level meter paired with the 378A04 low noise microphone and preamplifier. Due to the innovative design of the 378A04 which uses a prepolarized microphone and ICP (constant current) interface, the combination produces a highly portable system that is battery powered and intuitive to use for measuring low noise levels.
