-
product
Emergency Battery Test Fixture
TA-60
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
product
25-Pin D-Type Male Connector Block
40-965-025-M
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
product
Automotive Battery Production Line Tester
The Production Line Tester (PLT) is typically installed at the end of battery production lines (finishing). An electrical load test after formation charging is essential to assure performance and quality. The energy discharged during this test must be minimized to eliminate the need for recharging after testing.
-
product
Thermocouple Connectors
We are Europe's largest manufacturer of thermocouple connectors and accessories in IEC, ANSI and JIS colour codes. The full range of connectors are available from stock for immediate despatch.
-
product
Battery Load Tester
Battery Beak
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
product
Battery Discharge Tester
HTFDK / 796
Wuhan Huatian Electric Power Automation Co., Ltd.
Through continuously regulating discharge current, constant discharge current at set value can be realized.
-
product
Solder Cup Connector Kit
Y1141A
Used to build custom cables for 34951, 34952 – 50-pin Dsub male – 125 V.
-
product
Battery Extra Load Units
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
product
Battery Chargers
Is a device used to put energy into a secondary cell or rechargeable battery by forcing an electric current through it.
-
product
Waterproof Connectors
C.C.P. Contact Probes Co., LTD.
Corrosion Resistant and up to IPX8 water resistance.
-
product
44-Pin D-Type Male Connector
40-963-044-SM
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
Ultra Small Pins Connectors
C.C.P. Contact Probes Co., LTD.
Extremely small connectors for engineering that works with space constraints.
-
product
200 Pin LFH Connectors for Pickering
The connectors below are suitable to use with Pickering cards and modules that utilize a 200-pin LFH connector.
-
-
product
Ball-Point Connectors
C.C.P. Contact Probes Co., LTD.
Ball Point Connectors are used to connect moving targets without cables. Up to 25km travel distance!
-
product
Fine Pitch Connector Test
C.C.P. Contact Probes Co., LTD.
Our Ceramic/Aluminum sockets have a lifetime of up to 30,000 cycles.
-
product
PXI Battery Simulator 2.8 Amps
41-753-001
The 41-753 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals that can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
product
HN Connectors
Pasternack HN connector category contains many part numbers, the majority are RoHS and REACH compliant. HN connector series in this category will terminate to coax or terminal. These HN connectors are built to precise RF and microwave industry specifications. HN connector items are manufactured in male or female gender with 50 Ohm impedance. HN connectors are available in straight or right angle versions, as well as, 4 hole flange, bulkhead, 4 hole panel or mountless options. This series of connector in HN designs include clamp/solder, crimp/solder, field replaceable or solder attachment methods. Like the other of our over 40,000 RF, microwave and millimeter wave Pasternack products, this HN connector series is in-stock. Not just in stock, but also will ship the same day as they are purchased.
-
product
UNIVERSAL FILLER NECK CONNECTOR
SMOKE30
*Creates an air-tight seal with any vehicles EVAP system, eliminating the need for searching for the EVAP service port*Capless fuel system adapter works with your smoke machine to test EasyFuel™
-
-
product
Connector Block, 78-Pin D-Type, Female
40-965A-078-F
The 40-965A-078-F connector block provides a simple method of connecting to 78-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell.
-
product
USB Type B Test Connector
Test connector for USB Type B (4 pole) for contacting USB interfaces. Application in USB devices like hard disks, data carriers, power supplies, etc.
-
-
product
15-Pin D-Type Connector, Female
40-963-015-SF
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
44-Pin D-Type Connector, Female
92-960-044-F
This connector is designed to allow users to directly terminate cables with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
product
500 Pin SEARAY Cables - Connector to Connector For Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 500-pin SEARAY (250-port) connector.
-
product
EV Battery Pack Test Equipments
Guangdong Bell Experiment Equipment Co.,Ltd
All industrial battery tester from BELL lithium battery test chamber supplier meet the standards of GB31467.3, ECE-R100 and UL2580. The tests mainly simulating all the condition that driving an EV meet, including battery crush test, battery drop test, flammable test, temperature cycle test, short circuit test, thermal test, explosion test, and environmental test, etc.
-
product
20V Battery Internal Resistance/Voltage Tester
TOB-BVIR
Xiamen Tob New Energy Technology Co., Ltd
Portable Internal Resistance Tester for All Batteries 0 - 20V With Charging Adapter. TOB-BVIR Battery internal resistance tester can be used for measuring the Internal Resistance and Open CircuitVoltage of almost all of the commercial batteries such as Secondary battery, Lead acid battery, Nickle cadmium, Nickle-metal Hydride and Li-ion battery.
-
product
Battery Load Tester
BT-100
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
product
IP68 Connectors
Omnetics' designs these connectors to meet or exceed IP68 specifications. Find a solution that'll meet the demands of being in a harsh environment.
