PIN Diode Switch
-
product
Pull-Thru Adapter, Wired, TriPaddle, 68 Pin ML VHDCI, f/ AIT PXI-C1553
510140197
Pull-Thru Adapter, Wired, TriPaddle, 68 Pin ML VHDCI, f/ AIT PXI-C1553.
-
product
PXI Dual 12x8 Matrix, 1 Pole Switching
40-522-021
Medium density PXI dual 12x8, 1-pole matrix - it is also available inreed relayformats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable forswitching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems.The two banks may be used for operating a 4-wire measurement system (bank-1 for source,bank-2 for measure). Larger matrices may be constructed by daisy chaining the commonsignals from multiple PXI Modules.
-
product
Switch Probes
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
product
34945EXT Distribution Board, For Two 87222, L7222C Transfer Switches And Six N181x SPDT Switches
Y1154A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
Cable Assembly, Receiver, 20", TriPaddle, 37 Pin Female DSub, 1000V
540119030101
Cable Assembly, Receiver, 20", TriPaddle, 37 Pin Female DSub, 1000V.
-
product
PXI/PXIe Switched Guard Matrix, 8x4
40-590-102
The 40-590-102 (PXI) and 42-590-102 (PXIe) are modules that provide a switched guard 8x4 matrix solution with up to 1012 Ω channel to channel and channel to ground isolation.
-
product
6U VME 1/10/40 Gigabit Ethernet Switch
ComEth4000e
The ComEth4000e is a cutting-edge 1 slot & 2 slot options. 6U VME Layer 2/3 Ethernet switch compatible with VME 64x systems. Each configuration can also be built with or without a P0 connector.
-
product
7-way Flat (Spade) Pin vehicle side Circuit Tester
7893
Innovative Products of America
The 7-way Flat Pin Trailer Circuit Tester quickly and easily tests trailer circuits on most light to medium duty trucks and campers. Just plug the plug tester into the trailer plug socket and activate the lights, brakes, turn signal etc.
-
product
Wire Probe Needles Materials & Pin Diameters
Advanced Probing Systems, Inc.
Tungsten pins and tungsten-rhenium pins can be provided with either nickel plating or silver plating. Beryllium-copper pins are supplied with a silver plating coating.
-
product
General Purpose Switches
SMX-5XXX (General Purpose)
The VTI SMX-5xxx Series of general purpose switches deliver exceptional performance and reliability by implementing extensive signal path shielding, isolation and built-in health monitoring. Embedded virtual schematic control simplifies setup and debugging, allowing all relays to be engaged independent of application software and device drivers.Ideally suited for a wide range of discrete signal switching, the SMX-5xxx Series provides uncompromised measurement integrity ideal for the most demanding aerospace, defense and automotive automated test equipment (ATE) applications.
-
product
Standard Voltage 9 Pin D-Type Cables - Connector to Connector
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
PXI Single 46x4 Matrix, 1 Pole Switching
40-524-021
Medium density PXI dual 46x4, 1-pole matrix - it is also available inreed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
product
Ultra Small Pins Connectors
C.C.P. Contact Probes Co., LTD.
Extremely small connectors for engineering that works with space constraints.
-
product
96 Pin 1.27mm Pitch Micro-D Connector Blocks for Pickering
The connector blocks below are suitable to use with Pickering cards and modules that utilize a 96-pin micro-D connector.
-
product
PXI Switch - 16-CH General-Purpose SPDT Relay Module
PXI-7901
ADLINK PXI-7901 is a general-purpose (GP) switch module implementing 16-CH independent single-pole double-throw (SPDT) relays (1 Form C). PXI-7901 can connect one input to one output and be used as signal switching and routing for measurement system or ATE. Thanks to its high switching capacity, PXI-7901 can also be used to turn on or turn off devices such as motors, fans, heaters, and lights. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7901, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
product
Multiport Electromechanical Coaxial Switch, DC to 40 GHz, SP6T
87106D
The Keysight 87106D multiport switch improves signal accuracy in RF and microwave signal routing and testing applications. This high performance electromechanical switch provides unmatched isolation and a 0.03 dB insertion loss repeatability, which is warranted for the 5-million life cycle of the switch. The 87106D’s low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy. The repeatability and reliability of this switch guarantee measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications.
-
product
1x4 Switch
S-104
1 X 4 Switch slot module of FOTS system carries out the switching function that enables a single channel input to go to any of 4 outputs or a selected particular channel of 4 inputs to go to a single channel output. And its MEMS type switch module is bidirectional and transparent to signal format. It is remarkable that high speed switching and various driving program such as timed, manual or sequential switching mode are available through the combination of high speed response time switch and high speed FPGA processor. On the basis of less than 1ms switching time and 10ms minimum switching, high speed sequential switching can be installed easily by defining switching order, interval time and duration. Current switching channel status can be checked through LED fronted with slot, and present driving condition of optical switch can also be monitored through GOI or LCD monitor.
-
product
Diode Lasers
6-Watt Blue Engraving Laser
Advanced Photonic Sciences LLC
Can be used in laser engraving, marking, and cutting applications. Process wood, plastics, metals, anodized aluminum, stone, tile, and other materials. The adjustable spot can be adapted to the needed distance from laser to the material. The spot, with a size of <100 μm, creates very fine engravings and sharp cutting edges. The built-in driver accepts TTL and analog signals for power adjustments. The laser can be controlled between 0% and 100% of output power. It comes preset and needs only a power supply and a signal source.
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
The 42-205-008 (PXIe) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
160 Pin Female DIN to QuadraPaddle Flying Lead Cable, 48", 024070
VFL103124-048
Vendor Flying Lead (VFL) Cable, 160 Pin Female DIN to QuadraPaddle Leads, 24AWG Twisted Pair, 80 T/P's(1:2) 160 connection points, M2.5 x .45 fastener, CONN: 024070 WIRE: VPC, for PXI-2737, PXIe-2738 families, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 20" length.
-
product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 75Ω, MCX
40-830A-106
The 40-830A-106 (PXI) and 42-830A-106 (PXIe) are 75Ω RF switches with 6 separate SPDT relays slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
15 Pin D-Type Connector to Connector
The 15-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Male screwlocks are provided to secure the connectors to their associated products.
-
product
Line Powered Level Switch
ThePoint
ThePoint Line Powered provides a relay output switch and has hazardous area approvals making it a good choice for most of your point level application requirements. ThePoint sensing element offering is suitable for most temperature, pressure, and material types.
-
product
Cable Assembly, Receiver, 20", TriPaddle, to 37 Pin Female D-Sub
540016020103
Cable Assembly, Receiver, 20", TriPaddle, to 37 Pin Female D-Sub
-
product
PXI Single Bus 64-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-401
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
160-Pin DIN41612 Connector, Crimp Pin, Female
92-960-160-F
Suitable for users to create their own cable assemblies, this product can be supplied with or without the backshell. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the connector can be fitted with an optional screwlock assembly.
-
product
LED Drivers led Switching Power Supply
Dongguan Longwei Electronic Technology Co., Ltd.
LED drivers led switching power supply
-
product
cPSB 2.16 Compact Packet Switch 16 Slot, 14 node, 2F
107PS22616-4157R
CompactPCI CPSB 2.16 6U 16 slot,14 node, 2 fabric, fully compliant to the PICMG 2.16 Packet Switching Backplane specification.
-
product
SCR Diode Testers
SCRs and Diodes are used in the power sections of various power systems. A SCR Diode Tester is an important piece of equipment to determine if a SCR or a diode is defective in a power circuit. It is difficult and time-consuming to troubleshoot SCRs and Diodes with a digital meter.
-
product
Digital Temperature Switch
TCS
Monitor and control temperature in heating and cooling applications with the Series TCS Thermocouple Switch. The Series TCS offers a wide temperature range, two selectable alarm set, and an internal buzzer indicating alarm condition or error
