Discrete Component Testers
check connected individual semiconductor components.
-
Product
Benchtop Discrete Component Tester
Imapact 7BT
-
The 7BT Benchtop Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The 7BT automatic test system can be used in all test applications including incoming inspection, wafer probe, QC, engineering, production, final test, and high reliability.
-
Product
Impact Series Power Discrete Semiconductor Tester
-
The Impact Series Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.
-
Product
The Lorlin© Impact Series
-
Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The automatic test system can be used in all test applications including incoming inspection, wafer probe, QC, engineering, production, final test, and high reliability. The system tests most all discrete semiconductors with reliable, accurate, and repeatable results.
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
Receiver Tester
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
Product
Lightwave Component Analyzer
N4373E
Lightwave Component Analyzer
The new Keysight N4373E LightWave Component Analyzer offers the latest N5224B, N5225B, and N5227B network analyzers with 2-port or 4-port configurations. This LCA is the ideal measurement solution for tests of electro-optical components up to 67 GHz. It is the ideal test instrument for electro-optical components for 40G/100GbE, for 400Gbit/s and 1 Tbit/s coherent transmission systems, as well as Radio over Fiber (RoF) and aerospace and defense (A&D) electro-optical test applications.
-
Product
Passive Component Integration - PXIe
Passive Series
Passive Component Integration
The Passive PXIe module is a highly customizable PXIe module that can integrate the passive components of your choice.We can customize the Passive module with a wide range of passive components: WDM couplers, splitters, circulators, band-pass filters, PM beamsplitters, MUX, DeMUX and more.Our spec sheet contains a selection of popular configurations.Please contact us to discuss your specific requirements at sales@quantifiphotonics.com.
-
Product
Universal A/V Tester
Tester
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
Product
KVS Rugged Igniter Tester With Current Monitor
4314
Tester
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
Passive Component Integration
Passive Component Integration
Integrate passive optical components of your choice such as WDM couplers, splitters, band-pass filters, PM beamsplitters and circulators. PXIe and benchtop models support SMF, MMF and PMF.
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
110 GHz Lightwave Component Analyzer
N4372E
Lightwave Component Analyzer
The N4372E lightwave component analyzer helps you with optoelectronic tests with its measurement capability of 110 GHz in an extended wavelength range. It also offers RX testing up to 110 GHz in the full 1260 nm to 1620 nm range. It has a built-in optical power meter that enables you to check and control the operating power. The N4372E lightwave component analyzer's optical transmitter input port connects to an auxiliary tunable laser to verify S-parameters over wavelength.
-
Product
AXIe M8000 Series of BER Testers
Bit Error Rate Tester (BERT)
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
Passive Component Integration - MATRIQ
Passive Component Integration
The Passive is a highly customizable benchtop accessory that can integrate the passive components of your choice for convenient storage and integration into your test set up.We can customize the Passive module with a wide range of passive components: WDM couplers, splitters, circulators, band-pass filters, PM beamsplitters, MUX, DeMUX and more.Our spec sheet contains a selection of popular configurations.Please contact us to discuss your specific requirements at sales@quantifiphotonics.com.
-
Product
PXI Vector Component Analyzer, 100 kHz to 44 GHz
M9817AS
Vector Component Analyzer
The PXI vector component analyzer enables complex multiport device characterization with continuous wave and modulated signal measurements.
-
Product
Lightwave Detector
N4377A
Lightwave Component Analyzer
The N4377A Lightwave Detector is a USB-powered optical-electrical converter with built-in optical power meter capability. If used with a vector network analyzer or a spectrum analyzer it enables frequency domain applications in photonics.
-
Product
PXI Vector Component Analyzer, 100 kHz to 26.5 GHz
M9815AS
Vector Component Analyzer
The PXI vector component analyzer (VCA) enables complex multiport device characterization with continuous wave (CW) and modulated signal measurements.
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Hoist Tester
Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Tester
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
Component Testers
-
Unlike other handheld instruments such as LCR meters that make measurements using an AC signal with a specific test frequency, the 830C measures capacitance by applying a constant current that briefly charges, then discharges the connected capacitor.
-
Product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
-
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
Product
Power Discrete Tester
Mostrak-2
-
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
Product
Automated Discrete Semiconductor Tester (ATE)
5000E
-
Same Proven Technology as all 5000 Series Testers. High Speed Single Test Measure. Capable of Testing Multiple and Mixed Devices. 1KV Standard, 2KV Optional. 1NA to 50A Standard, 100A Optional. 0.1NA Resolution. Complete Self Test. Auto-Calibration. RDSON to 0.1MOHM Resolution. Windows Application Software. Optional Scanner. Optional Wafer Mapping. Optional Curve Trace. MOSFET, IGBT, J-FETTriac, SCR, Sidac, Diac, Quadrac, STS, SBS Transistor, Diode, Opto, Zener Regulator, MOV, Relay. UNDER $23,000.00
-
Product
LCR Component Meter with Component Impedance Measurement
LCR45
-
The new LCR45 does everything that the popular LCR40 does, but we've added some significant enhancements. The LCR45 features a new high capacity micro and high resolution ADCs.*Fluid measurements of L, C and R (continuous readings with selectable hold function).*Fine resolution for improved performance at low inductance/capacitance/resistance.*Auto and Manual component type.*Auto and Manual test frequency.*Frequencies: DC, 1kHz, 15kHz and 200kHz.*Display of component values, complex impedance, complex admittance and magnitude/phase.
-
Product
16-CH Discrete Input 16-CH Discrete Output Modules
HSL-DO16-UC / HSL-DI16-UC
Input/Output Module
- Support 16 DI channels and 16 DO channels- Transmission speeds: 3/6/12 Mbps- RJ-45 phone jack for easy installation- Compact design to meet space limitation and cost-effective requirement- Fuse design to protect digital output channelover-current
-
Product
Switching Components
-
Designed to minimize layout restrictions and maximize ease of operation, Omron’s innovative switching components make manufacturing flexibility more attainable than ever.
-
Product
16-CH Discrete Input 16-CH Discrete Output Module
HSL-DI16DO16-M-NN
Input/Output Module
- Input voltage: ±40 V (Max)- Output switching capacity: Single channel 500 mA; all channels 60 mA at 24 VDC- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ±10 mA (Max) , ±12.5 mA (Peak)- 16-CH digital input and 16-CH digital output. "NN" type for NPN sinking type sensor input or dry contact and NPN sinking type output- Slave ID consumption: 1
-
Product
RF Components
-
Using a Vector Network Analyzer (VNA) for RF component testing for design and manufacturing is based on how the component performs. The analyzer is used in multiple ways from design to manufacturing to tuning, field monitoring and maintenance of antennas, filters, mixers, amplifiers, circulators, isolators, and other RF components. Key considerations component designers should pay attention to when finding an analyzer that fits their needs is a great dynamic range, low trace noise, and fast measurement speed.
