Physical Layer
Tests hardware, electrical and procedural interface to the transmission medium.
-
Product
Inmarsat-C Physical Layer Tester
CPLT
-
Square Peg Communications Inc.
Square Peg Communications Inc.’s Inmarsat-C Physical Layer Tester (CPLT) is a software application that runs on the generic high-rate Physical Layer Tester (PLTH) platform. The CPLT supports testing of the physical layer performance and protocol implementations of Inmarsat-C Mobile Earth Stations (MESs) and Land Earth Stations (LESs).
-
Product
Physical Layer Test System
N19301B
-
The N19301B Physical Layer Test System (PLTS) 2022 software is a powerful signal integrity tool for today’s high-speed digital designers.
-
Product
Iridium Physical Layer Test Systems
PLTS
-
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
-
Product
Physical Layer Switching Systems for copper LAN, WAN, DSL, Telco apps with RJ style connectors.
RJ Series
-
The RJ Series of computer controlled switching systems are designed for physical layer switching of multiwire signals on RJ style connectors. Since the system uses mechanical relays it acts exactly like a piece of cable which makes it perfect for testing networks without altering the signals or regeneration. These systems are typically used for Ethernet LAN 10BaseT through 1000BaseT, DSL including ASML through GFAST, CAT5 through CAT6A cable testing, USB up to 2.0, RS232, RS422, RS485 up to 8 wire at 20 Mbps and many other applications switched over RJ45 connectors up to 8 wires. They may also be used as lab automation switches, network testing switches, patch panels, network redundancy switches or any number of physical layer applications.
-
Product
CCIX
-
The CCIX® Consortium was founded to enable a new class of interconnect focused on emerging acceleration applications such as machine learning, network processing, storage off-load, in-memory data base and 4G/5G wireless technology. CCIX is a high performance, low latency interface that is based on PCIe Physical layer, up to speeds of 32GT/s. Teledyne LeCroy provides a range of Protocol Analysis tools to support development and debug of CCIX based devices.
-
Product
NI-9881, 1-Port C Series CANopen Interface Module
781673-01
-
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
-
Product
PLTS Measurement And Calibration
N19303B
-
The new Physical Layer Test System (PLTS) 2024 is the industry standard for signal integrity measurements and data post‑processing high-speed interconnects, such as cables, backplanes, PCBs, and connectors. Signal integrity laboratories worldwide have benefited from the power of PLTS in the R&D prototype test phase.
-
Product
PCIe Mini CAN Controller
PCie-Mini-CAN-FD
-
The PCIe-Mini-CAN-FD is a PCI express controller with an integrated CAN FD transceiver supporting data rates up to 8Mbps. The CAN FD controller meets the specifications of the ISO11898-1:2015 high speed Controller Area Network (CAN) data link layer and meets the physical layer requirements of the ISO11898-2:2016 high speed CAN specification.
-
Product
Isolated Controller Area Network (CAN)
-
ADI isolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
Product
ARINC 3U/6U CompactPCI Interface Card
CPCIC3/6-A429
-
Alta Data Technologies’ CPCIC-A429 interface module offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB).Encode or decode almost any ARINC-429 physical layer signal.
-
Product
Non-Isolated Controller Area Network (CAN)
-
ADI nonisolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 16-Channel, 2-Pole
40-739-002
-
The 40-739-002 (PXI) and 42-739-002 (PXIe) are dual 16-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
PXI-8531, 1-Port PXI CANopen Interface Module
781061-01
-
1-Port PXI CANopen Interface Module—The PXI‑8531 is a high-speed CANopen interface for developing applications with the NI‑Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of products and applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The PXI‑8531 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA DS301. It also features a batch SDO editor with electronic data sheet (EDS) file integration and layer setting services (LSS) support for slave node configuration.
-
Product
IsatData Pro Physical Layer Tester
DPLT
-
Square Peg Communications Inc.
The IsatData Pro Physical Layer Tester (DPLT) supports testing of the physical layer performance and protocol implementation of Mobile Terminals (MTs) implementing Inmarsat’s IsatData Pro (IDP) services.
-
Product
Industrial Ethernet Physical Layer Devices
-
The ADI Chronous™ Industrial Ethernet physical layer (PHYs) portfolio includes solutions for standard 10 Mbps, 100 Mbps, and 1 Gbps. It also features the new 10BASE-T1L technology for single-pair Ethernet.Our industry-leading low latency and low power PHY technology maximizes data transmission and signal integrity in deterministic applications by reducing cycle times and system power consumption. It enables superior synchronization of signals across the industrial network and supports the development of TSN.
-
Product
100-FX Fiber Optic Ethernet PMC
3006
-
The Ethernet 100-FX Adapter provides a single port Ethernet connection using Fiber Optic media. An AMD 79C973 Ethernet controller provides a integrated link and physical layer for operating at 100 Mb/s. The Fiber Optic connector used on the board can be either the ?SC Duplex? style, or the ?ST RX/TX? style and is identified by the Technobox Part Number.
-
Product
2 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTE
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 8-Channel, 2-Pole
42-739-004
-
The 40-739-004 (PXI) and 42-739-004 (PXIe) are dual 8-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
AXIe M8000 Series of BER Testers
-
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
C Series PROFINET Interface Module
-
The C Series PROFINET Interface Module provides two PROFINET interface ports that enable you to reliably connect programmable logic controllers (PLCs), I/O, sensors, and drives over long distances in industrial environments. PROFINET is an application protocol that uses familiar concepts from PROFIBUS that are implemented on the physical layer of Ethernet. The C Series PROFINET Interface Module includes NI-PROFINET driver software for human machine interface (HMI) and supervisory control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces.
-
Product
Optical Limiting Amplifiers
-
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
Product
NFC Physical Layer Test System
IQnfc+
-
LitePoint provides turn-key software that facilitates test coil calibration, executes test plan and provides detailed waveform analysis and flexible APIs to customize test flow in the labs.
-
Product
MIPI Test Fixtures & Software
-
The UNH-IOL has been a contributing member of the MIPI Alliance since 2007 and tests all mobile devices looking for MIPI conformance and physical layer testing including C-PHY, D-PHY, DSI, and CSI-2. All UNH-IOL MIPI Test Fixtures and Tools are available to member and non-member companies. Below are just some of the MIPI Solutions we offer. For a full list please visit our MIPI Test Fixtures page.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 4-Channel, 2-Pole
40-739-006
-
The 40-739-006 (PXI) and 42-739-006 (PXIe) are dual 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
Ethernet Media Converter
-
A physical layer equipment which interconnects the Ethernet, Fast Ethernet, or Gigabit Ethernet on copper UTP and the related fiber optics network. Ethernet media converter meets corresponding IEEE 802.3 standards.
-
Product
Industrial Ethernet Platform Solutions
-
ADI’s Industrial Ethernet platform solutions are complete network interface solutions designed to provide device connectivity for a large range of industrial, instrumentation, and other equipment. These solutions include both a physical layer and data link layer that manage the industrial protocol and network traffic for a host processor. ADI Chronous™ network interface solutions are complete communications subsystems that enable quick and simple inclusion of Industrial Ethernet connectivity to any end system.
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTD
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Dual-Port HS-1760 Test & Simulation PXI Express Module
PXIe-C1760
-
Avionics Interface Technologies
3U PXI form factor fits into PXIe or PXI hybrid slotTwo independent ports programmable as NC or NT(s) simultaneouslyTwo SFP sockets accepts FC-0 AS5653 or AS5625/AS5627 transceiversSupports NC-to-NT transfers, NT-to-NC Transfers, Mode Codes, and BroadcastFull control of sequence and exchange managementSupports large file exchangesFull Monitoring of all Bus TrafficTriggering and FilteringFull Error InjectionSupports DMA for high speed streaming of data to/from the boardIRIG-B Time Code Encoder/Decoder for Data CorrelationOptional Special FC-0 physical layer compliance with SAE AS5653Optional fcXplorer Analyzer for decoding HS1760 frames
-
Product
64 Gbaud High-performance BERT
M8040A
-
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Coherent Transmission Test Instruments
-
Optical modulation analyzers provide detailed insights into the complex modulated optical signals at the physical layer to determine signal quality or evaluate components that are designed for IQ modulation and demodulation.
