Distributed Antenna System
-
Product
DAS
-
The Distributed Antenna Systems (DAS) function is to enhance the performance of a wireless network coverage of a specific area. DAS is a network of antennas which are all connected to the same source. The DAS solution is more efficient than having a large single antenna to cover an area and that’s why it is highly suited for in-buildings service and a restricted outdoor area. Amphenol Procom offers a wide range of both indoor antennas and passive devices, especially for Public Safety applications.
-
Product
DAS Antennas
-
In-Building Distributed Antenna System (DAS or i-DAS) antennas are low profile and designed to be mounted discreetly to a hard or tiled ceiling. Used in a series throughout large buildings, campus areas or even in below ground sections of a building the antennas can provide a distributed LTE or Wi-Fi signal to where it is required most. With a growing demand for in-building connectivity and higher data rates, larger smart or connected buildings require a series of antennas in order to distribute signal around the building or campus area.
-
Product
DAS / 4G LTE Power Dividers, Combiners
-
INSTOCK Wireless Components, Inc
INSTOCK Wireless offers wideband RF power divider / combiners optimized for DAS (Distributed Antenna System), 3G, and 4G LTE modem gateway splitting applications. INSTOCK cell-band and DAS splitters are commonly used for in-building wireless (IBW) network deployments. Available in 2-way thru 48-way configurations spanning 698-2700 MHz with exceptional performance. Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
Product
CW Transmitters
-
The Praxsym CW Transmitter is a complete, portable continuous wave test source. Used as an input source to test a distributed antenna system, the Praxsym CW Transmitter can provide test signals aiding in the design and optimization of in-building and outdoor networks.
-
Product
Omni-Directional Radiation Pattern, Compatible For WiFi5/6/6E/7
AIW-512-C
-
Dipole antenna with omni-directional radiation patternSupport 6GHz bandCompatible for WiFi5/6/6E/7RP-SMA male connectorOperating Temperature: 0 ~ 70℃
-
Product
Distribution Board, For 8 N181x SPDT Switches
Y1150A / 34945EXT
-
Connects the 34945EXT to 8 N181x SPDT to route the power and control signals from the driver module to the switches
-
Product
34945EXT Distribution Board, For Two 87222, L7222C Transfer Switches And Six N181x SPDT Switches
Y1154A
-
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
Product
Medalist i1000D Small Foot Print Inline and Offline In-Circuit Systems
U9405A
-
Unlike traditional bridge type board handlers that add a 3rd party equipment on your offline ICT systems, we provide a one-stop shopping experience when you are automating your in-circuit test.
-
Product
Battery Cell Formation System
17000 series
-
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
Product
Mezzanine System
5174
-
The 5174 provides two major functions, serving as a precision Voltage Controlled oscillator board and a variable frequency source board. These features can be use together or independently. As a variable frequency source, the 5174 provides a high-resolution variable clock source that is based upon a reference clock supplied by the ECM carrier.
-
Product
IFC Antennas & Radome Systems
-
System solutions providing inflight internet and live TV connectivity including satellite communications (SATCOM) systems, protective radome enclosures, antenna mounts, bird strike solutions, and adapter plates.
-
Product
Mezzanine System
5047
-
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
Product
Communications System Analyzer
Freedom R8200
-
The Freedom R8200 from Astronics Test Systems represents a major step in the evolution of the Land Mobile Radio Test. The Freedom R8200 is the first and only test instrument that combines comprehensive digital and analog LMR testing with the ability to measure important RF network characteristics, such as Distance to Fault (DTF), Return Loss, and Voltage Standing Wave Ratio (VSWR). The Freedom R8200 is also the only service monitor with the abilityto display advanced RF Parameters in a Smith Chart for more complicated network analysis
-
Product
Mezzanine System
5089
-
The 5089 provides eight channels of 12 bit A/D conversion using the Analog Devices AD7328, and is suitable for medium resolution medium speed applications.
-
Product
Systems Integration (SIL) Lab Data Acquisition
-
Bloomy’s SIL data system allows testing and simulation of every system component on the aircraft. The functionality of these complex integrated systems are fully tested, debugged, and verified safely in the lab prior to flight testing. This reduces cost and schedule for new aircraft. Bloomy has applied its expertise to multiple SILs.
-
Product
Mezzanine System
5093
-
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
Product
Single Sensor Enhanced Vision Systems
-
Rely on the industry leading Max-Viz enhanced vision systems (EVS) from Astronics to enhance your safety and situational awareness while flying.
-
Product
Lighting Systems for Aviation
-
Flying on every major platform, Astronics offers decades of proven experience in delivering standard and custom lighting solutions that illuminate the world’s aircraft. From commercial to business to military, chances are we offer experience with your type of fixed-wing or rotorcraft program.
-
Product
Omni-Directional Radiation Pattern, Compatible For WiFi 5/6/6E/7
AIW-511
-
Dipole antenna with omni-directional radiation patternSupport 6GHz bandCompatible for WiFi5/6/6E/7RP-SMA male connectorOperating Temperature: 0 ~ 70℃
-
Product
Airframe Electrical Power Systems
-
Rely on Astronics CorePower® airframe electrical power systems, where solid-state technologies deliver highly efficient, clean power that improves aircraft operation through weight and system wiring savings.
-
Product
Inflight Entertainment System Hardware
-
Innovative IFEC solutions that enable connectivity, entertainment, and control.
-
Product
Emergency Systems
-
Safety and survival products which aid in on-board emergencies, aircraft evacuation, and search and rescue operations.
-
Product
Checkpoint Security System
ConneCT
-
The ConneCTTM Checkpoint Security System is an advanced aviation security explosive detection system (EDS) engineered to deliver superior threat detection, dramatically improved passenger throughput, and low total cost of ownership.
-
Product
Mezzanine System
3560
-
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
Product
VME Data Acquistion System
ADM-31
-
The VME-based ADM31 data acquistion system supports up to 48 differential or up to 96 single-ended analog inputs. The ADM31 control card is an intelligent A/D subsystem master or slave device that controls the analog A/D cards. Up to two A/D cards can be configured with the control card to complete the A/D system.
-
Product
FMV Compression System
daq8580
-
The Daq8580 is designed to address the challenges of processing, transporting and storing full motion video through video encoding, and can interface with a wide variety of analog and digital I/O and process standard video formats up to 1080p30 as well as computer resolutions up to 1600x1200.
-
Product
Mezzanine System
5033
-
ECM P/N 5033 provides eight channels of RS485 / RS422 I/O. The 110 ohm termination for each channel is enabled or disabled in software. Disabling termination saves power by eliminating unneeded or redundant termination. Speeds of up to 20 Mega bits per second are possible, but this design also features a 250K bits per second slower edge rate mode. The 250K bit mode is valuable when EMI is more of a concern and throughput is not important. All channels power up as inputs with the outputs disabled.
-
Product
Computing VITA System
CRS 48.5
-
The CRS 48.5 is a complete, integrated, pre-tested, ready-to-run HPEC rugged subsystem enabling faster development/deployment at lower cost and risk using the most advanced VITA 48.5 compliant air-flowthrough cooling to allow the integration of up to eight quad core Intel® Core™ i7 processing nodes.
-
Product
In-Process Wafer Inspection System
7945
-
Chroma 7945 wafer chip inspection system is an automated inspection system for pre and post diced patterned wafers. Change kits enable switching between various applications by allowing different carriers including metal frame or grip ring.
-
Product
Mezzanine System
5041
-
ECM P/N 5041 provides eight channels of RS485 / RS422 I/O with fixed 120 ohm termination for each channel. Speeds are up to 30M bits per second. All channels power up as inputs. Also transceiver inputs are always enabled for loop back diagnostic use when the outputs are enabled. Software can enable outputs on a channel by channel basis.
