Solid State Relays
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 2.5 GHz, 75 Ω, 1.6/5.6, Remote Mount, Failsafe
42-780B-753-E
-
The 40-780B-753-E (PXI) and 42-780B-753-E (PXIe) are triple failsafe SPDT 2.5 GHz 75 Ω unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 18 GHz, 50 Ω, SMA, External Termination, Failsafe
42-781A-121
-
The 40-781A-121 (PXI) and 42-781A-121 (PXIe) are single failsafe SPDT 18 GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI Mixed Configuration Relay Module - 3 Cells Populated
40-138-AA-BB-CC-DD (3 CELL)
-
The 40-138 2A Relay Module with 3 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
PXI Dual Microwave SPDT Relay 18GHz 50 SMA - Internal Termination
40-781-022
-
This dual microwave SPDT relay module is part of the 40-781 range that consists of one or two changeover switches capable of switching frequencies to 18GHz in 50 Ohm. Versions are available with either internal or external terminations and connections are made via front panel mounted high quality SMA RF coaxial connectors.
-
Product
PXI/PXIe Power Relay Module, 2xSP4T, 20 Amp
42-166-202
-
The 40/42-166-202 is a PXI/PXIe high density power relay module with 2xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations.
-
Product
Solid State RF and Microwave Switches
-
The Solid State RF and Microwave Switches have the following advantages over mechanical switches; long operating life, fast switching time, low power consumption and small size. Mechanical RF and Microwave Switches usually have lower insertion loss, higher isolation and higher RF power handling capability. However, because of the advantages mentioned above, Solid State RF and Microwave Switches are to prefer if very low insertion loss and/or very high isolation is not needed.
-
Product
PXI 8 Slot BRIC Solid State 96x8 1-Pole (3 sub-cards)
40-563A-121-96X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Power Relay Module, 10xSPST, 16 A
40-161A-003
-
The 40/42-161A-003 is a PXI/PXIe 10xSPST power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 2.5 GHz, 75 Ω, 1.6/5.6, Remote Mount, Failsafe
42-780B-752-E
-
The 40-780B-752-E (PXI) and 42-780B-752-E (PXIe) are dual failsafe SPDT 2.5 GHz 75 Ω unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, External Termination, Failsafe, Remote Mount
40-781A-321-E
-
The 40-781A-321-E (PXI) and 42-781A-321-E (PXIe) are single failsafe SPDT 26.5 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI 8 Slot BRIC Solid State 128x8 1-Pole (4 sub-cards)
40-563A-121-128X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXIe Power Relay Module, 12xSPST, 16 A, With Interlock
42-161A-002-HI
-
The 40/42-161A-002-HI is a PXI/PXIe 12xSPST power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
2x8 USB Solid State Switch Matrix, 300 KHz To 6.5 GHz
P9165A
-
P9165A 2x8 USB solid state switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 18 GHz, 50 Ω, SMA, Internal Termination, Failsafe, Remote Mount
42-781A-021-E
-
The 40-781A-021-E (PXI) and 42-781A-021-E (PXIe) are single failsafe SPDT 18 GHz microwave relay modules with internal terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI 4 Slot BRIC Solid State 64x8 1-Pole (2 sub-cards)
40-563A-021-64X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Product
PCI 32xSPST 2Amp Relay Card
50-132-002
-
The 50-132-002 32xSPDT relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
Product
CPCI-Relay32
CPCI-Relay-32
-
CPCI Bus Interface 3.3 / 5 Volt PLX 9056 66MHz 32-bit, PCI r2.2compliant
-
Product
Reed PXI 16 x SPST Reed Relay 2.5 Amp
40-136-011
-
Pickering Interfaces 40-136 Power Reed Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. The 40-136 is suitable for voltages to 200V and current to 2.5A. Available in Normally Open (SPST & DPST) configurations. Connections are made via a front panel mounted 50 or 78-pin D-Type connector.
-
Product
Solid State NMR
-
Magnets for NMR experiments are required to have a high homogeneity, which can be maintained over a wide range of field. Experiments are performed at fixed frequency and the spectrum is obtained by sweeping the magnetic field. This requires the field to be stable in spatial homogeneity and change steadily and repeatedly over time.
-
Product
PXI/PXIe Solid State Attenuator, Hex, 6GHz, 50Ω, SMA
43-182B-006
-
The 41-182B-006 (PXI) and 43-182B-006 (PXIe) are programmable RF attenuator modules with 6 channels in 2 slots capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuator uses solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
PXI Versatile Multiplexer, Solid State, 350mA, 60V
40-681A-001
-
The 40-681A-001 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 350mA current and 60V voltage handling. The 40-681A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
-
Product
Solid State PIN Diode Transfer Switch, 100 MHz to 18 GHz
P9400C
-
The Keysight P9400C solid state PIN diode transfer switch offers outstanding performance in terms of port-to-port isolation, switching speed and low insertion loss over a broad operating frequency range of 100 MHz to 18 GHz. The P9400C is particularly well suited for ultra-fast RF and microwave switching applications in instrumentation, communications, radar, switch matrices and various other test systems where high isolation, speed and lifetime of a switch is critical.
-
Product
PXI/PXIe Power Relay Module, 24xSPDT, 5 Amp, 50-Pin SGMC Connectors
40-158-002
-
The 40/42-158-002 is a PXI/PXIe high density power relay module with 24xSPDT switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
PXI Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, Failsafe
40-780B-531
-
The 40-780B-531 (PXI) and 42-780B-531 (PXIe) are single failsafe SPDT 26.5 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI/PXIe Solid State Attenuator, Triple, 6GHz, 50Ω, SMA
43-182B-003
-
The 41-182B-003 (PXI) and 43-182B-003 (PXIe) are programmable RF attenuator modules with 3 channels in one slot capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuators use solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
Multiplexer/Solid State Recorder
TTC MSSR-2010
-
Curtiss-Wright Defense Solutions
The TTC MSSR Chapter 10 multiplexer with solid state recorder is used in demanding applications such as airborne instrumentation recording. Two versions are available; the MSSR-110C, a stackable version that works with TTC’s MCDAU and MEDAU encoders, and the MSSR-2010-SA, a stand-alone version that includes the power supply.
-
Product
PXI/PXIe Microwave Relay, Quad SPDT, 26.5GHz, 50Ω, SMA
40-780B-534
-
The 40-780B-534 (PXI) and 42-780B-534 (PXIe) are quad SPDT 26.5GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions .Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI 2 Amp Multiplexer, 8-Bank, 8-Channel 2-Pole
40-659A-102
-
Model 40-659A is an 8 Bank 8 Channel Multiplexer module with 2-pole switching, It uses high quality electromechanical relays and is suitable for switching signals up to 2Amp, 300VDC/250VAC. The 40-659 module is suitable for multiplexer applications where two signals are required to be switched simultaneously, for example send and return signals in a telecoms system. It is also suitable for applications where reed relay based multiplexers do not have sufficient power handling capability such as switching medium power AC or DC loads or for slaving external relays, contactors and solenoids.
-
Product
PXI-2599, 26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module
778572-99
-
26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module - The PXI‑2599 is a general-purpose single‑pole double‑throw (SPDT) switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2599 is also well-suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
