Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
Product
Free Modbus Device Tester Software
-
Global Multimedia Private Ltd.
This software was developed to test Information Displays made by Global Multimedia for modbus protocol compliance. It can be used to test your firmware on a serial device for Modbus RTU conformance.
-
Product
16-Port Serial Controller
PMC523
Controller
The PMC523 provides a flexible solution for technology insertion by integrating multiple serial I/O channels onto a single board computer (SBC) with a PCI Mezzanine Card (PMC) site. This gives customers affordable protection from obsolescence and a smart evolutionary path to enhanced software ultimately improves performance and increases efficiency.
-
Product
Digital Source Capture Unit
DIO2
Capture Unit
The DIO-II module is a multimode digital source and capture unit. In Low Speed Mode it provides a 20-bit parallel or 24-bit serial I/O capability running at speeds up to 50 MHz. In High Speed Mode, the DIO-II provides a 16-bit parallel I/O capability up to 200 MHz. In both Modes, the Clock is generated by a low jitter PLL source that is capable of generating clocks from 320 kHz up to 1 GHz.
-
Product
Oscilloscope - 500 MHz, 2 Analog Channels
DSOX4052A
Oscilloscope
500 MHz2 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
Power Supplier QP303E 2x30V/3A
-
*on / off switch output section*two independent adjustable DC output*independent outputs serial and parallel*constant voltage and current*Low ripple and noise*four digit LED displays three*for 16 hours at full load*automatically search out
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
790661-01
Embedded Controller
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
HDMI SCDC/EDID Controller
AJSC-1
-
The Allion AJSC-1 is a SCDC/EDID Controller that was designed for the latest HDMI 2.1/1.4 source/sink compliance electrical testing. It is used for HDMI source/sink device testing with the aim of controlling and emulating HDMI 2.1/1.4 EDID, SCDC signals. As the AJSC-1 is compatible with test equipment from Tektronix and Keysight, it is truly an adaptable and multi-functional test device.This test fixture can be managed through a serial interface using a terminal emulator software such as Tera Term. Windows-based GUI software is also available.
-
Product
Digital I/O
-
Curtiss-Wright Defense Solutions
Curtiss-Wright Digitial I/O cards include interfaces to LVDS, Camera Link, Serial intrefaces, CANbus and customizable I/O. With over 20 years experience in the design and production of top quality COTS signal acquisition hardware, we deilver PMC, XMC and PC/104 modules that can cope with the toughest operating environments.
-
Product
C/D-PHY CSI-2/DSI Analyzer
Envision X84
Analyzer
is the first combination C-PHY/D-PHY analyzer in single platform. The Envision X84 supports C-PHY/D-PHY and Cameral Serial Interface (CSI-2) and Display Serial Interface (DSI/DSI-2) on a single hardware platform. Envision X84 supports C-PHY version 1.1 and D-PHY 2.1 as well as CSI-2 version 2.1 and DSI version 1.3 and DSI-2 version 1.1. The Envision X84 offers Silicon ad device designers, integrators and validation engineers a complete, robust yet flexible tool to ensure the correct and efficient operation of Camera and Display over C-PHY and D-PHY implementations.
-
Product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 3U VPX
Model 52751
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the FPGA for custom I/O- Optional 400 MHz 14-bit A/Ds- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
1 GHz A/D and D/A with Virtex-7 FPGA - XMC
Model 71730
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One 1 GHz 12-bit A/D- One 1 GHz 16-bit D/A- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual uSync clock/sync for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
GPIB Smart Serial Interface
Model 4866
-
* Adds an IEEE-488.2 compatible GPIB Interface to any serial device.* Provides all IEEE-488.2 functions and a Status Reporting Structure for the serial device.* Uses SCPI commands to set the serial configuration, GPIB address and user's IDN message.* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals.* Operates with asynchronous serial devices, with standard serial devices and with 'smart' serial devices such as embedded computers or microprocessors.* 1 U high rack mount kit mounts one or two 4866s* Includes US 115 VAC Power Adapter, Manual and Support CD.
-
Product
FlashPDF Program Manager
-
The FlashLink Program Manager software is a user-friendly and feature- packed program available for FlashLink Reusable data loggers. It can be downloaded from the DeltaTrak website, must be purchased and requires a serial number to complete installation. The Set-Up Wizard and Import function become active only when the FlashPDF Program Manager Software interfaces with FlashLink® Reusable data loggers. In the Set-Up Wizard, data tags can be formatted, alarms set, data logging options customized, and summary of configuration settings can be saved in the configuration folder. The configuration can also be imported and uploaded to a different reusable data logger. The easy-to-use software shows the recorded data in numeric or graph formats, with customizable fields, statistical data and alarm functions
-
Product
SATA (Serial ATA)
-
Serial ATA (SATA) is a data transfer technology designed to move data to and from storage devices such as disk drives, ATAPI drives, host bus adapters (HBA), and port multipliers. SATA is a serialized enhancement and replacement to parallel IDE. Since SATA ratification in 2003 and its move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with its industry leading protocol analysis and traffic generation capabilities.
-
Product
PMC-BiSerial II-NG1
-
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
-
Product
LV Iron Core Smoothing Reactors
-
Smoothing Reactors are serially connected reactors inserted in DC systems to reduce harmonic currents and transient over currents and/or current ripples in DC systems. They are necessary in order to smooth the direct current wave shape to reduce losses and improve system performance.
-
Product
10-Pin RJ50 Male to 25-Pin DB-25 Male Serial Cable
182846-02
Serial Cable
Serial conversion cable for 4-port serial board to a DB-25 male connector.
-
Product
3U CPCI I/O & Comm Board W/Gig-E Switch
75D4-H2
Multifunction I/O
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
Product
Oscilloscope
DSOX3034A
Oscilloscope
350 MHz4 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
PXIe-8431/16, 16-Port, RS485/RS422 PXI Serial Interface Module
781473-02
Serial Interface
The PXIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCIe-8432, PCI Express, 2-Port, Isolated, RS232 Serial Interface Device
781744-01
Serial Interface
The PCIe‑8432/2 is a high-performance interface for high-speed, port-to-port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial … interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
ARINC 818 Switch IP Core
-
ARINC 818-2 is a point-to-point, serial protocol, high bandwidth, low latency protocol for the transmission of uncompressed video, audio, and data during blanking period, widely used in AVIONICS application. Since a vast portion of the newer applications of the ARINC 818-2 have several displays with many channels of ARINC 818-2, switching has turned out to be more imperative. ARINC 818-2 switch can support up to 12 channels. Multiple switching modes such as broadcast, unicast, multicast, and mixed are also supported.
-
Product
ELOS CompactPCI Serial
ELOS-CPCIS
-
ELOS is an embedded rugged CompactPCI Serial system platform for a wide range of applications. The cost-efficient concept is based on modular building blocks that make this product extremely flexible.
-
Product
6-Ch 200 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Kintex UltraScale - 6UVPX
Model 58821
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Six 200 MHz 16-bit A/Ds- Six multiband DDCs (digital downconverters)- Two DUC (digital upconverter)- Four 800 MHz 16-bit D/As- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Switching Unit
ZET 454
-
The ZET 454 switching unit is intended for serial switching of 72 circuits of ZET 452 control devices to one of the sixteen sockets. The ZET 452 electric circuits control device is connected to a socket on the ZET 454 switching unit front panel. On the front panel of ZET 454 there also are sockets for tested device circuits connection, which is performed using the adapter harnesses.
-
Product
Serial To Ethernet Converter & Device Server
SERIP-100
-
SERIP-100 is proconX' low-cost Industrial device server offering one or two software selectable RS-232/422/485 serial ports and a 10 Mbit Ethernet port.
-
Product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
Serial Communication Cards
-
Advantech serial communication cards include RS232, CAN bus, and COM cards.
-
Product
Low Cost Emulator
EB-XAS3
-
* Emulates P51XAS3x Microcontrollers * Real-Time Operation up to 30MHz * 3.3V or 5V Voltage Operation * Source-Level Debugger for C and Assembler * MS-Windows Debugger Software * Reduced Set of C-Compiler and Assembler * Support for ROMless and ROMed Microcontrollers * 64K of Code Memory * Performance Analyzer * Real-Time and Conditional Breakpoints * 68-pin PLCC Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115 Kbaud
-
Product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - XMC
Model 71671
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Extended interpolation range from 2x to 1,048,576x- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual uSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface, up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
