Surface Profiling
See Also: Surface Profile, Surface Profilers
-
Product
Wafer Edge Profile Measurement
WATOM
-
WATOM can carry out fully automatic, non-contact measurements of the edge profiles and diameter in accordance with SEMICON standards. A special feature is the system's ability to make measurements of the mark cut into the edge of the wafer to indicate the crystal orientation. Because of its high measurement accuracy of less than 1.5 µm, leading wafer manufacturers across the world use WATOM for shop-floor geometrical quality control.
-
Product
Surface Defect Inspection System
-
Wafer for inspection of surface condition of specular flat substrate, glass substrate, others φ 100 ~ φ 300 compatible
-
Product
Continuous Surface Current Mapping & Wave Monitoring System
SeaSonde
-
The SeaSonde HF radar system by CODAR Ocean Sensors is your solution for making continuous, wide-area ocean observations. The SeaSonde will provide you with years of real-time data over large coverage areas, with ranges up to 200 km — This is not possible with any other technology!
-
Product
Digital Automated Interferometer and Microscope for Surface Inspection
DAISI-V3
-
The ultimate production interferometer for measuring end-face geometry on single-fiber connectors, equipped with a revolutionary «no-exterior-moving-parts» mechanical design.
-
Product
0.50° Accuracy Full Attitude Surface Dynamic Motion Sensor
DMS-550
-
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.
-
Product
Optical Profiler
DRK8090
-
Shandong Drick Instruments Co., Ltd.
This instrument uses noncontact, optical phase shift interferometry method does not damage the surface when measuring graphics can be quickly measured by a variety of three dimensional surface morphology, and analyzed to calculate the measurement results. Suitable for measuring a variety of blocks, the surface roughness of optical components; scale, dial the groove depth; magnetic (optical) disk, the head surface texture measurements; structural morphology of coating thickness and coating trough structure at the boundary of the grating; silicon surface roughness measurement and the graph structure and so on.
-
Product
Non-contact Surface Texture And Contour Measuring Instruments
-
From sub-nano level surface roughness to milli level profile with 3D.Tokyo Seimitsu provides non-contact type surface roughness and contour measuring instruments with the confidence born out of many years cultivating know-how of surface roughness measurements.
-
Product
Fixed Writing Surface for 24" RA Cabinet
WSA-124
-
This fixed shelf / writing surface for a double-bay RA cabinet spans the full width of the cabinet and extends 18” in front.
-
Product
FlowQuest Acoustic Current Profilers
-
FlowQuest is a line of Acoustic Current Profilers manufactured by LinkQuest Inc., a company renown for its innovation, capability and product quality. The FlowQuest current profilers are ideal for measuring currents and flows in oceans, harbors, lakes and rivers. With its capability for significantly longer range, standard deepwater depth rating and seamless integration with third-party sensors and LinkQuest acoustic modems, the FlowQuest system is not just a current profiler. It also serves as a focal point for your underwater deployments.
-
Product
19" Drawer with Writing Surface, Unshielded, 3.5"H x 24"D
DR-031924-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Refractive Index Profiler
S14
-
The S14 Refractive Index Profiler complements optical fiber preform analysis measurements by providing highly accurate and precise characterization of the refractive index profile of drawn single-mode, multimode, and specialty fibers using the RNF (Refracted Near Field) technique. The S14 index profile data produces fiber geometry information directly. Manufacturers can also use S14 data for the prediction of fiber transmission parameters such as mode field diameter, cut-off wavelength, and chromatic dispersion.
-
Product
24" Drawer with Writing Surface, Unshielded, 7"H x 30"D
DR-072430-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Non-contact 3D Optical Profilers
-
LuphoScan platforms are interferometric, scanning metrology systems. They are designed to perform ultra precision non-contact 3D form measurements mainly of rotationally symmetric surfaces such as aspheric lenses.
-
Product
Compact Low Profile Load Cell
1000 Series
-
Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.
-
Product
Surface Thermometers
-
Tel-Tru® Manufacturing Company
Tel-Tru Surface Thermometers are designed to measure surface temperatures on a wide variety of surfaces and are available in several configurations.
-
-
Product
3U OpenVPX 6 Slot variant Profile BKP3-CEN06-15.2.2X-3
1OVX306UY6-1X11R
-
Single star, no expansion plane| control plane 3U, 6 Slots.
-
Product
Low Profile PCI Express 2-Port
7202ec
-
The 7202ec low-profile PCI Express serial interface provides two RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7202ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
Product
Digital Surface Resistance Meter
-
NEW Enclosure with Rubber Grip EdgesThinner and narrower design is easier to hold and provides protection from drops.NEW Quick Check ButtonBypasses the 15 second electrification period to allow quick spot checks.NEW Battery Compartment
-
Product
Surface Inspection Gauge for the Shop Floor
4D Inspec Surface Gauge
-
Your product description goes here.
-
Product
Surface Comparators & Magnifier
127
-
Designed for use with the Elcometer 127 illuminated magnifier, each surface comparator has a hole in the centre allowing for clear visual comparisons to be made.
-
Product
Cable Assembly, CAT-5E Ethernet, Thin Profile, 10M
151733-10
-
8-Pin Male Ethernet to 8-Pin Male Ethernet, CAT-5E Ethernet Cable - The 8M-8M Ethernet Cable connects devices to network hubs or switches. The cable has straight-through wiring and is available in different lengths and thin profile options.
-
Product
3D Sensor (Shiny Surfaces)
reflectCONTROL
-
reflectCONTROL is designed specifically to meet the high quality requirements that ensure high quality for shiny surfaces. The system based on deflectometry projects a striped pattern onto the measurement object. Defects on the surface cause deviations from the striped pattern which are recorded by cameras and evaluated by software.
-
Product
Surface Measurement Instrumentts
-
Analyze surfaces texture with nanometer precision is already a technological challenge, but TR Scan Premium is able to perform this task with unprecedented speed! The TR Scan Premium is used in workshops and laboratories worldwide. It is completely designed and manufactured in Switzerland by TRIMOS. The TR Scan is focusing on Digital Holographic Imaging Technology. Accuracy, speed, ease of use and modular construction make it ideal for all types of surface measurements.
-
Product
Narrow Profile Power Supplies
-
Where only a narrow mounting space is available, Acopian Narrow Profile power supplies fit where many others cannot. Choose from Series A (high performance - model numbers begin with the letter A) and Series B (general purpose - model numbers begin with the letter B) models with output ratings up to 150 volts, up to 3.5 amps.
-
Product
Elcometer Rubert & Rugotest Surface Comparator
129
-
The Elcometer 129 Surface Comparators are available in two models to suit your requirements.
-
Product
MiniCTD Profiler
-
The miniCTD has been developed to provide a cost-effective tool for the collection of CTD Profiles, without compromising the quality of the data.
-
Product
Low Profile PCI 24 Channel TTL Digital Interface
8018
-
The 8018 Low Profile PCI digital I/O interface provides 24 channels of buffered drive digital I/O emulating 8255 mode zero. The board can be utilized for PC-based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems.
-
Product
DB37F-DB37M LP, Low Profile I/O Cable, 37-pin Female DSUB to Male DSUB (1m)
154302-01
-
Low Profile I/O Cable, 37-pin Female DSUB to Male DSUB (1m)
-
Product
VisionGauge Digital Optical Comparators / Digital Profile Projectors
500 Series
-
The VisionGauge Digital Optical Comparator is The Fastest, Easiest, Most Accurate Way to Compare a Part to a CAD File. Our VisionGauge Digital Optical Comparators: Produce a very high contrast image with very sharp edge profiles so that there is no problem viewing it in full daylight Are much more accurate, more powerful, much faster, include CAD Auto Pass/Fail and CAD Auto-Align, works directly with CAD data so there no mylars or templates are needed, etc.
