Extender Boards
move out from slot circuit card giving access thereof.
See Also: Extenders, Extender Cards, Test Boards, Bus
-
Product
IF Digital Processing Board for Demodulation and Combining
LS-35-R
-
The Lumistar LS-35-R is part of the Lumistar family of digital processing boards used for programmable telemetry systems. The LS-35-R consists of a digital processing main board with two high capacity Xilinx Virtex-5 arrays. The LS-35-R provides a two-channel IF Receiver with Pre/Post detect combining, multimode demodulators with data rates up to 40 Mbps, bit synchronizer outputs, Viterbi decoding, spectral and constellation display, BER reader display and 70 MHz IF modulator with calibratednoise feature. The all-digital design assures a consistent product with high reliability and long-term stability.
-
Product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
Carrier Board
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
Product
Termination Board
MSTB 010
-
Termination Board allows quick and secure connection of discrete wires to a DAP 820 or DAP 840. MSTB 010 combines analog and digital termination on the same board, and is the only termination board that can be used by the boards listed at the end of this page.
-
Product
PCI Evaluation Board
BCM91250E
-
The BCM91250E is a full-length PCI evaluation board with the SiByte® BCM1250 dual-processor System on a Chip. The board is designed for software development and for developing PCI applications that require high-performance processors.
-
Product
Sensor Boards
SensorXplorer™
-
Each sensor board can be used together with the SensorXplorer board.The SensorXplorer boards acts as a USB to I2C interface between Vishay's freely available software modules and the sensor boards. The sensor boards also have test pins for the I2C interface, allowing you to connect them to your own platform.
-
Product
4K Autofocus USB3.1 Gen1 Camera Board (Color)
See3CAM_130
-
See3CAM_130 is an UVC-compliant AR1335 sensor based 13MP autofocus USB camera with iHDR support. It supports 4K Ultra HD (3840x2160) at 30fps over USB3.1 Gen1 in compressed MJPEG format. This See3CAM_130 can also stream Full HD (1920x1080) at 60fps and HD (1280x720) at 60fps in both uncompressed and compressed MJPEG formats. This autofocus USB camera board is also backward compatible with USB 2.0, although in USB 2.0, this camera supports fewer resolutions at lower frame rates.
-
Product
SparkFun SAMD21 Development Board
Qwiic Micro
-
Looking for a super small microcontroller to use with the Qwiic eco-system? The SparkFun Qwiic Micro is molded to fit our standard 1"x1" Qwiic standard size which makes it one of our smallest micro-controller offerings to date. At it's core is the powerful and versatile ATSAMD21E18, which is an ARM Cortex M0+, 32-bit microcontroller, with 256KB of flash memory that can run at up to 48MHz! It has 12 digital pins which include 5 analog pins, SPI, I²C, and an additional UART data bus as well as a Qwiic connector for easy integration into the Qwiic ecosystem and I²C prototyping.
-
Product
PCI Evaluation Board
BCM91125E
-
The BCM91125E is a full-length PCI evaluation board with the SiByte® BCM1125H MIPS processor System on a Chip (SoC). The board is designed for software development and developing PCI applications, which require high-performance processors. The BCM91125E can be plugged into a PCI slot in any PC, workstation or server, or can be used as a stand-alone device.
-
Product
GPIB T8 Cable, 2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender
183164-500
GPIB Cable
2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender - The GPIB T8 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T8 Cable with a pair of GPIB extenders to increase the cable length of your system up to 2 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T8 Cable is offered in different lengths.
-
Product
Performance Board For LSI Tester
-
Place inner layer GND plane all over. Impedance control of signal line and crosstalk prevention, etc. contribute to improvement of characteristics in various ways.
-
Product
Interface Module for the Multimode, Multiprotocol Excalibur 400 Family of Carrier Boards
M4K1553Px(S)
Interface Module
The M4K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M4K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M4K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M4K1553PxS single function (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.
-
Product
Development Board
SOM-DH7000
Carrier Board
Development Board for COM-HPC® Extension Modules. COM-HPC® Extension Size E, RunBMCv1.5 260pin socket interface (A2). 1 PCIe x1 reserved for BMC add-in card (A1) Rich extension: 4 x PCIe x16, 1 PCIe x8, 1 PCIe x4, 2 PCIex1 (Gen 5).
-
Product
PCIe I/O & Comm Board
79C3
Multifunction I/O
NAI’s 79C3 is a PCIe Multifunction I/O and Communication Board with three independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
16-bit, 200KHz, 4SE/2DIFF Isolated Analog Input Board
APCI-3016-4
-
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
-
Product
16-CH Discrete Input 16-CH Discrete Output Daughter Board Module
HSL-DI16DO16-DB-NN
Strain/Bridge Input Module
- Slave ID consumption: 1 16-CH NPN sinking type sensor inputs or dry contact and 16-CH - NPN sinking type outputs- Photo couple isolation voltage: 2500Vrms- Input impedance: 4.7KΩ- Input current: ??10mA(Max), ??12.5mA(Peak)- Input voltage: ??40V (Max)- Output switching capacity:300mA/ch at 24VDC- Terminal Base:HSL-TB64 or HSL-TB32-DIN- LED indicator: Power, Link and I/O status
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for two M.2 or NGSFF (NF1) PCIe SSD Modules
SKU-086-32e
-
This Squid PCIe Carrier board can support up to two M.2 or NGSFF (NF1) PCIe SSD (solid state drive) modules, with M-key. Supported module dimensions are 2230, 2242, 2260,2280 or 22110 in length, and a width of up to 32 mm. SSD modules of any capacity may be used, from any vendor, and in any combination.
-
Product
VME Form Factor Extender, 3U, 60mm
111FFE3006-01XX
-
The VME form factor extender 3U 60 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
Product
Multi-Protocol Board
EXC-8000cPCI
-
The board supports up to 6 modules, and each module represents an independent test and simulation device. Most modules are based on existing Excalibur products such as the 1553 Px family and the ARINC429 RxTx.
-
Product
cRIO-9038, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller
783850-02
Embedded Controller
1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9038 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. The cRIO-9038 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. Additionally, the cRIO-9038 supports an extended temperate range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
PXIe HSS Optical FPGA Board
PXIe-8324
-
The Conduant PXIe-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface.
-
Product
Self/Fast Boot use on SKY Boards
-
Each of these loads occur internally to each SKYbolt board at the speed of the internal SKYbolt busses; we are not limited to the speed of the VME bus, the host VME interface or the disk. These program loads also occur in parallel so the startup time is independent of the number of SKY boards in the system.
-
Product
Relay Output Board
VME-2232A
Relay Output Module
VME-2232A is a 32-Channel Relay Output Board with Built-in-Test (BIT). Software compatible with the VMIVME-2232 and the VMIVME-2533.
-
Product
SMT & THRU HOLE LOADED BOARD TEST PROBES
SERIES 43
-
MechanicalMINIMUM CENTERS: .075 (1.91)FULL TRAVEL: .250 (6.35)WORKING TRAVEL: .167 (4.24)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 3 amps continuous at working travel, non-inductiveRESISTANCE: At 35 mA test current,30 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper or steel hardened to 55-60RC, both 24Kt gold plated over nickelBARREL: Nickel silver with 24Kt gold plated ID and OD over nickelSPRING: Music wire, 24Kt gold plated over nickel
-
Product
Osprey ISA Q-Bus Adapter board
9476-Q-B
-
Qbus Controller board for Osprey ISA/EISA bus compatible. Occupies PC slot adjacent to item 2 or 3. I/O Adapter logic provides Programmed I/O and DMA access to "real" Qbus compatible controllers (those not otherwise emulated).
-
Product
Extended Test Lead Kit
U1161A
Accessory Kit
The Keysight U1161A extended test lead kits are compatible with the U1230, U1240, U1250, and U1270 Series handheld digital multimeters. The set includes two extension test leads (one red and one black), two test probes, medium-sized alligator clips, and 4 mm banana plugs.
-
Product
PCI Express Receiver Board
AD12-2000-IRIGB
-
The AD12-2000-IRIGB is a high performance wideband 0.3-1.8GHz PCIe-bus receiver on a single PCIe Gen3 board, that can continuously digitize a wide portion of the RF spectrum, with a 3.6GSPS 12-bit A/D that can be synchronized with stability of better than +/- 100 picoseconds with respect to an IRIG-B 1PPS signal and global time codes from a satellite receiver or local site time reference. Designed for demanding military, scientific, industrial, communications, safety and electrical power utility applications, the AD12-2000-IRIGB has 60dB of gain adjust range (manual and AGC with programmable loop bandwidth), a wideband noise figure of 9dB, +11dBm 1dB compression point, and 2dB peak-to-peak ripple over the 300MHz to 1.6GB frequency spectrum.
-
Product
SparkFun MicroMod WiFi Function Board
ESP32
-
The SparkFun MicroMod ESP32 Function Board adds additional wireless options to MicroMod Processor Boards that do not have that capability. This special function board acts as a coprocessor that takes advantage of Espressif's ESP32 WROOM to add WiFi and Bluetooth® to your applications.
-
Product
PMC Dual Channel MIL1553B Board
MS 1722
-
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- 553B controller based design- 2 dual redundant channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
Millimeter-wave Operation With Frequency Extenders For M980xA PXI VNA
S95560B
Vector Network Analyzer
banded vector network analyzer (VNA) using the M980xA PXI VNAs and N5252AW or N5262BW Frequency Extenders.
-
Product
Multi Protocol Boards
-
The EXC-4000 carrier board series was developed to meet the needs of avionic testers for multi-protocol integrated, digital bus testing. Modules may be selected out of a growing list which currently includes MIL-STD-1553/1760, MMSI, H009, ARINC-429, ARINC-708/453, Serial (232/422/485), Discrete and CAN bus. Additionally, an IRIG B decoder implements a global time stamp relative to the IRIG B pulses. The need for higher density, different protocols, and multi-channel on one integrated test card has made the EXC-4000 series very successful.
