Filter Results By:
Products
Applications
Manufacturers
Substation
transform and distribute electrical power.
See Also: Power Distribution, Switchgear, High Voltage Transformers
-
product
Automation Operations
Schweitzer Engineering Laboratories, Inc.
Substation automation uses substation and feeder operating functions and applications to optimize the management of capital assets and enhance operation and maintenance efficiencies with minimal human intervention.
-
product
Multifunction Substation Test Set
STS 4000
STS 4000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers, designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
product
Earth Tester
TAURUS PRECIOHM ET
The TAURUS PRECIOHM ET is one of the specially designed products by TAURUS to measure earth resistivity and earth resistance in a power station. These tests are performed based on 4 point (Wenner) and 3 point (fall of potential) methods respectively. All electrical equipment in the substation and power stations are electrically connected to station earth mat with earth electrodes. The earth electrode ensures that in the event over voltage on the system due to system fault or lighting discharges etc., the parts of the equipment which are normally ”dead” as far as voltages are concerned; do not attain dangerously high potentials. An earth electrode will only be effective so long it has a low resistance to the earth and can carry large currents without deteriorating. Thus the resistance of earth electrode should be low to give good protection and it must be continuously measured and monitored in all the substations and power stations.
-
product
Multi-Sensor Thermal Imaging Camera for Condition Monitoring
A310 PT
FLIR A310 pt thermal cameras can be installed almost anywhere to monitor the condition of your critical equipment and other valuable assets. Designed to help safeguard your plant and measure temperature differences, they allow you to see problems before they become costly failures -- preventing downtime and enhancing worker safety. FLIR A310 pt is ideal for various applications that require temperature measurement capabilities including: substation, transformer, waste bunker, and coal pile monitoring.
-
product
Magnetic Field Generator
PFM61000-8A
PFM61000-8A Magnetic Field Generator is high reliability test equipment with stable performance, specially designed for electrical and electronic products for measuring immunity characteristics and requirements of normal frequency magnetic fields. It provides an accurate basis for the tested equipment in the immunity test of normal frequency magnetic field. The generator can imitate the magnetic field environments such as residential, commercial, industrial and mining enterprises, power plants, as well as middle and high substation. It fully meets IEC61000-4-8 and GB / T17626.8 standards.
-
product
Total Substation Maintenance Program
S. D. Myers' Solutions offers Substation Maintenance Services which provide the means to solve your substation and transformer needs. One phone call gives you access to the S. D. Myers' team, our expertise and experience, as well as our network of partnerships, all working toward the goal of extending the relaible and cost-effective life of your substation equipment.
-
product
Earth Meter
EM-4055
The EM-4055 Earth Meter is a digital, microprocessor-controlled instrument that allows to measure the earth resistance and ground resistivity (using Wenner´s method), as well as to detect parasitic voltages present in the ground. This instrument is well suitable to measure earth systems in power substations, industries, distribution networks, etc., according to VDE 0413. It is also suitable for soil resistivity measurements, in order to optimize the earth systems project
-
product
Electrical Measurement Equipment
Portable equipment designed for maintenance and commissioning of substations and power plants. Low resistance micro ohmmeters, digital timers, windings resistance, contact resistance, circuit breaker timing and motion, phase angle and frequency measurements.
-
product
Megohmmeter
GM-20kV / 782
Wuhan Huatian Electric Power Automation Co., Ltd.
It is suitable for testing the characteristics of electrical insulation resistance in substations, power plants, remote power cables or buried cables.
-
product
AC High Voltage Break Down Tester
High Voltage Breakdown Testers also known as Hipot Testers or Insulation Testers are a necessity for any Transformer testing, Substation equipment testing, Cable testing, Panel testing and testing of various insulating materials. Insulation testing is very important to ensure and maintain the safety of electrical equipments and also for the safety of operator.
-
product
Flexible KRT Relay Testing Software Support
ISO9001
KINGSINE Electric Automation Co., Ltd.
Kingsine relay testing system V2 is the newest relay testing system which developed by kingsine Electric Automation Co., LTD. It is the professional software platform customized for power plant, transformer substation , protection realy producer and other related enterprises through our long-term R & D accumulation and practice and intergrated the newest technic and design concept from world-wide.
-
product
Primary Test Equipment
LET-2000-RD
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
product
IEC 61850 Testing
HAOMAI Electric Test Equipment Co., Ltd.
IEC 61850 is an international standard defining communication protocols for intelligent electronic devices at electrical substations. It is a part of the International Electrotechnical Commission's (IEC) Technical Committee 57 reference architecture for electric power systems.
-
product
Mini Automatic Transformer Observation System
mini-ATOS
The mini-ATOS, is a professional multifunctional power transformer and substation diagnostic system. This compact and intelligent instrument can perform many routine and advanced tests such as Winding Resistance (WR), Dynamic Resistance Measurement (DRM), Turns Ratio (TR), Frequency Response of Stray Losses (FRSL), Magnetic Balance, and other diagnostic parameters. With the built-in fully automatic multiplexer, only a one-time connection is required for nearly all functions, which saves a considerable amount of time. The portable, rugged case is perfect for use anywhere onsite or in a laboratory. It is specially designed for fast and easy measurements with the well-known high precision and quality of all Raytech instruments.
-
product
Automatic Relay Test Set
DRTS 34
DRTS 34 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 4 Voltage generators simultaneously available.
-
product
Partial Discharge Testing Equipment
AR700
PD Defect Location in High-Voltage Equipment Insulation by Acoustic Sensors To act on deteriorating insulation the source of PD must be known.The insulation defects produce partial discharges, which emits electrical impulses, radiation of electromagnetic waves as well as acoustic signals.The AR700 measures acoustic signals with multiple sensors spread over the transformer. Then the software determines the failure location using the time difference of all incoming signals. Finally, these coordinates are shown in a 3D model of the transformer. AR700 device is used for measuring of acoustic signals on the external surfaces of gas-insulated breakers and substations, power transformers and other tank high-voltage equipment. The acoustic signals are caused by partial discharges in the insulation, which is the sigh of the defects.The advantage of “AR700” device is the quick installation of the acoustic PD sensors on the external surface of high-voltage equipment tank. The sensors have magnetic holder that is why there is no need to de-energize the equipment for the sensors installation. “AR700” device has 4 syn-chronic channels for acoustic signal measurement. This gives the possibility not only to find the defects in the insulation, but also to locate them. The location function of the “AR700”device is unique for acoustic devices.
-
product
Power System Automation
Schweitzer Engineering Laboratories, Inc.
Automate your power system with SEL instrumentation and control devices. Substation automation uses data from IEDs, control and automation capabilities within the substation, and control commands from remote users to control power system devices.
-
product
Split-type Cable Fault Location System
Weshine Electric Manufacturing Co., Ltd
Electricity networks have had to become more flexible, reacting more quickly to the changes and needs of higher performance. This demand for flexibility is especially true where multiple generation sources occur, such as the intermittent power from renewables like solar and wind energy. While modern SMART grid technology can quickly identify faults in sub-station and generating units, cable faults can still occur anywhere on the network.
-
product
200 A HIGH-CURRENT MICRO-OHMMETER
MPK-203x
The MPK-203x high-current micro-ohmmeter is a portable, microprocessor-controlled instrument. Has optimized filters and protections for measurements in electrical substations. Can be used to accurately measure very low contact resistances of high voltage circuit-breakers and switches, busbars, etc., with test currents up to 200A. It employs the 4 terminals-method (U/I measuring principle) to avoid errors caused by test leads and their contact resistances.
-
product
Distributed I/O
Schweitzer Engineering Laboratories, Inc.
Expand the I/O of SEL relays and communications processors, reduce copper in substations by transferring I/O from remote locations over fiber, and provide electrical isolation to avoid ground paths and induced noise and interference.
-
product
Electrical Grounding Analysis
GroundMat
SKM GroundMat is a program for substation ground grid design and analysis. It is designed to help optimize grid design or reinforce existing grids of any shape. It uses a general-purpose finite element algorithm for potential analysis and graphical facilities to validate ground system efficiency
-
product
Primary Current Injection Test Set
T 3000
T 3000 is a primary current injection testing system designed to perform primary tests requested in substations commissioning. It allows to perform different tests and measurements on current transformers, voltage transformers, power transformers, protection relays, energy meters and transducers
-
product
Primary Current Injection Test Set
T 2000
T 2000 is a portable current transformer test set which allows to perform many different measurements such as saturation, ratio and polarity tests and CT winding resistance test. Substation maintenance and commissioning test equipment, T 2000 is extremely appreciated by electrical engineers for its high accuracy and portability.
-
product
Certified Solutions
Advantech has several certified products for the railway automation or power & energy automation, such as IEEE 1613 controllers, EN50155 switches and IEC 61850 substation controllers. All these certified solutions are for the transportation or power & energy industries. The certified products are verified by individual third party organizations to help your system work more reliably in substation automation applications. EN50155 certified solutions, including EN50155 switches, are designed for passenger information system, the IEC 61850-3 and IEEE 1613 certified solutions, such as IEC 61850 substation controller and IEEE 1613 controller, are suitable for substation automation and wind power grid automation, the Det Norske Veritas (DNV) certified solutions which are integrated with ECDIS, are ideal for navigation applications. The certified solutions Advantech offers means engineers can create reliable and safe working environments.
-
product
Data Collection and Analysis System
3002
The Model 3002 SER System is a state of the art data collection and analysis system. It is suitable for application in an electrical utility substation or plant environment to produce Sequence of Event (SER) data in conformance with PRC-002-1 and PRC-018-1.
-
product
DC High Voltage Break Down Tester
High Voltage Breakdown Testers also known as Hipot Testers or Insulation Testers are a necessity for any Transformer testing, Substation equipment testing, Cable testing, Panel testing and testing of various insulating materials. Insulation testing is very important to ensure and maintain the safety of electrical equipments and also for the safety of operator.
-
product
Current Transformer Testers
Vanguard Instruments Company, Inc.
Performs CT excitation, current-ratio, polarity, and phase angle testsMeasures insulation resistance and winding resistance of the CT seconday windingsMeasures the CT's secondary burdenTest record header information including company, substation name, circuit ID, manufacturer, CT serial number, operator name, and test record-commentsBuilt-in 4.5-inch wide thermal printerPlot Multiple Saturation CurvesStores up to 128 CT test plans and 140 test records internallyUSB, Bluetooth, and USB Flash drive interface
-
product
Substation Alarm ManagerAnnunciation and Data Viewer
SAM
Applied Systems Engineering, Inc
Applied Systems Engineering, Inc.''s Substation Alarm Manager (SAM) was developed in order to provide Power Utilities with a simple way to show the current status and data within a substation. SAM Substation Annunciator utilizes our extensive protocol library and allows for a wide variety of substation equipment to be monitored. Data can be acquired either by eavesdropping on an active circuit or directly polling an RTU/IED. Collection data is transmitted to SAM through the OPC protocol. This allows SAM to perform its alarm monitoring function either locally at the substation or at a remote site.
-
product
Substation Automation
Schweitzer Engineering Laboratories, Inc.
Enable high-performance control and monitoring schemes. Protection applications include directional element-based bus protection and replacement of tone-channel equipment for communications-assisted blocking, unblocking, permissive, and transfer trip schemes.
-
product
Primary Test Equipment
LET-4000-RD
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
