EV
automobile singly powered by electrical energy.
See Also: Electric Vehicle, Hybrid Electric Vehicle, EV Charging Station
-
Product
Battery Cycle Test Systems
-
Chroma Systems Solutions, Inc.
High precision, integrated battery charge / discharge cycle test systems designed for lithium ion and other chemistries and applications including EV batteries and energy storage systems. Chroma’s battery test equipment provides advanced features including regenerative discharge systems that recycles energy from the battery back into the channels in the system or to the grid. Systems are configurable and flexible with multiple channel capabilities that can be upgraded as testing requirements change.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
41-752A-111
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Regenerative AC Emulator, 600 VAC, 63 A, 45 KVA, 3‑Phase
SL1202A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Mission-Critical Chart Recorder
EV-5000
-
The EV-5000 is ideal for mission-critical data acquisition applications where digital storage and paper printouts are required. Engineered to be a direct replacement for the field-proven Everest® series of chart recorders from Astro-Med, the EV-5000 eliminates the need for costly retrofits and provides the same high-quality charts, easy data review and permanent records. Print recorded data on standard 16.3” (414 mm) Z-fold chart paper.
-
Product
VHF/UHF Nav/Drone Analyzer
EVSD1000
Analyzer
The R&S®EVSD1000 VHF/UHF nav/drone analyzer is a signal level and modulation analyzer for use aboard medium sized drones. It measures ILS, GBAS and VOR ground stations during startup, maintenance and servicing and analyzes air traffic control communications (ATC COM) signals. The mechanical and electrical design is optimized for drone based measurements of terrestrial navigation systems.
-
Product
Wireless Data Logger
EVA100
-
The new highly integrated measurement system "EVA100" is supporting Power Supplies, SMU( 4 quadrant DC Signal Measurement Units ), Pattern Generators, Arbitrary Waveform Generators, Digitizers and Oscilloscopes necessary for complete analog / mixed-signal / sensor / digital IC devices and Modules including Electronic Control Unit (ECU) for automotive evaluation and measurement.This new measurement system allows engineers quickly to build their own measurement environment without combining several standalone instruments.
-
Product
multiprocessor
EVP6472
-
Sundance Multiprocessor Technology Ltd.
The EVP6472 is the industry’s first off-the-shelf multiprocessor, multicore solution that features dual Texas Instruments (TI) TMS320C6472 Digital Signal Processors (DSPs)
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 750 V Isolation
43-752A-012
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Wind Power Solution
EVO ACCIONA
-
The EVO ACCIONA is custom-made with firmware and fixtures designed specifically for Acciona turbines. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Shaft Alignment
EVO
-
The evolution of laser shaft alignment towards simplicity and confidence continues with the EVO.
-
Product
Scienlab Charging Discovery System (CDS) – High-Power Series
SL1047A
Battery Test Platform
The Scienlab Charging Discovery System – High-Power Series from Keysight enables you to test charging interfaces of electric vehicles (EVs) and EV supply equipment (EVSE) during high-power charging up to 1,500 V DC and ±600 A DC. With the CDS can perform all necessary conformance and interoperability tests according to worldwide charging standards. Our new solution, which features the separate Scienlab Cooling Unit with interchangeable liquid-cooled charging adapters, also enables a high-power upgrade of the SL1040A Scienlab Charging Discovery System - Portable Series.
-
Product
HEV/EV Battery Equipment
-
Our line of HEV / EV Battery Equipment combines sophisticated electronics, advanced technology, and user-friendly operation. The EVc Battery Reconditioner processes all types of nickel metal hydride HEV batteries. Worldwide, the EVc has proven to be a neccesary workhorse for any hybrid auto shop or garage. The EVd Power Tester monitors individual module voltages during high power battery discharge. The EVd also features a "smart" charger that performs complex CCCV charging. We are currently developing technology to process and rebalance the Li-ion batteries for electric vehicles.
-
Product
VHF/UHF Nav/Flight Analyzer
EVSF1000
Analyzer
The R&S®EVSF1000 is a signal level and modulation analyzer for installation in flight inspection aircraft. It performs measurements on ILS, VOR and marker beacon ground stations during startup, maintenance and servicing and analyzes ATC COM signals.
-
Product
Event Based Image Sensors
EVS
-
Event-based Vision Sensors (EVS) help alleviate this issue by only sending data from pixels who have detected a change in intensity. This allows them to minimize the volume of data that is transmitted over the sensor’s data bus while minimizing the processing resources need to analyze the image. On top of this, individual pixel autonomously responds to illuminance changes allowing the sensor to detect small and/or high frequency changes with lower bandwidth requirements.
-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
Miniature Vacuum Controller
VSO-EV
-
VSO-EV is an electronic vacuum pressure control unit designed for laboratory instruments where precision vacuum control is required.
-
Product
Triple Quadrupole Mass Spectrometer
EVOQ™
-
The EVOQ triple quadrupole for liquid chromatography (LC-TQ) was designed for a singular purpose—to reliably quantify thousands of real samples in the fastest sample-to-report time possible. It delivers exceptional sensitivity, precision, accuracy, linearity, and a wide dynamic range for your multiple reaction monitoring (MRM) assays.
-
Product
HEV & EV Power Tester
EVd-40
-
The EVd-40 Power Tester is a pre- and post-reconditioning tool for quality control of aftermarket HEV & EV battery production. The equipment integrates a “smart” charger (Sorensen XG 1700 or Kepco KLN 1500W) with NuVant Systems high power discharge electronics. The "power test" discharges battery packs at high power (10,000 watts), while tracking module voltages. The software monitors up to 40 module voltages at a time, identifying any weak modules. The "smart" charger performs charging constant current (CC), constant voltage (CV) and complex mixed mode constant current – constant voltage (CCCV) charging protocols at voltages up to 600 V. This enables recharge of any type of rechargeable battery.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 1 kV Isolation
43-752A-103
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, 1 kV Isolation
43-752A-102
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
MicroSemi-SiC-Module / Evaluation Board
EV-MS4135PL1Z-U1 Pre-Release
-
High power evaluation board, up to 1200V & 50A @ 200kHz switching frequency featuring the combo ADI ADuM4135 isolated gate driver + LT3999 isolated power supply controller + Microsemi SiC power module in half bridge configuration.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 1 kV Isolation
41-752A-112
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
ECT / ECA Eddy Current Flaw Detector
EVi
-
United Western Technologies Corp
The EVi works directly with the EddyView Family of probes and accessories. UniWest’s unmatched selection of standard and advanced display features set a new standard for flexibility of applications, ease of use, interpretation of data and overall operator accuracy. The key to the EVi’s ground-breaking performance is the display of a visual image of the surface area under inspection alongside the customary and selectable eddy current signal displays (impedance plane, A-scan or strip charts). The EVi provides a high precision, easily readable display of surface conditions enabling improved interpretation of data while giving more accurate discernment of cracks, pits, gouges and fretting.
-
Product
Automated Measurement System
EVG®40NT
-
The EVG40 NT (stand-alone tool) and the AVM (HVM-integrated module) enable measurement of lithography relevant parameters like critical dimension, as well as bond alignment accuracy.Because of the high-measurement accuracy, it is possible to verify compliance to tight process specifications and instantly optimize integrated process parameters.
-
Product
300W to 600W - Single Output
EVS Series
-
*Suitable for battery charging*300W Convection Cooled, 600W fan model*Adjustable Current Settings*Five year warranty
-
Product
IR Inspection System
EVG®20
-
The EVG 20 offers a fast inspection method, especially for fusion bonded wafers. A live imageof the entire wafer via IR transmission supports void detection down to a radius of 0.5 mm. The infrared inspection system is a perfect match for fusion bonding processes either as the stand-alone EVG 20 tool or as a station in EVG''s integrated bonding systems.
-
Product
Chromapoint Large Slope Angle Optical Heads
EVEREST
-
Sciences et Techniques Industrielles de la Lumière
Born from the last STIL innovation, EVEREST chromatic confocal sensor head contains the best of research and development in terms of sensors.EVEREST series offers an extended measurement range with the highest performances.
-
Product
EVS for Experimental and Homebuilt Aircraft
-
Give your aircraft a safety boost with a Max-Viz enhanced vision system (EVS) from Astronics. These systems help you see through smoke, fog, and night to help you avoid runway obstructions, severe weather, and more.
-
Product
RH850 Family (Automotive Only)
RH850/C1x
-
The RH850/C1x microcontrollers have Resolver/Digital (RDC), Enhanced Motor Control (EMU) unit making this product suitable for motor control for Hybrid Electric Vehicles (HEV) and Electric Vehicles (EV).
-
Product
UV-NIL / SmartNIL® Systems
-
EV Group provides a complete product line for UV-based nanoimprint lithography (UV-NIL), including different single-step imprinting systems, large-area imprinters as well as step-and-repeat systems for efficient master fabrication. Besides soft UV-NIL, EVG offers its proprietary SmartNIL technology with multiple-use polymer stamp technology. The efficient and robust SmartNIL process provides high pattern fidelity, highly uniform patterned layers and minimum residual layers, combined with easy scalability in wafer size and production volume. EVG´s SmartNIL redeems the long-term promise of nanoimprinting being a high-performance, low-cost and volume-capable manufacturing technology for mass production of micro- and nanoscale structures.
