Tone Generators
A device, which puts out test tones at various frequencies to align a tape machine or for other testing purposes. (www.testing1212.co.uk)
-
Product
Tone Generators
-
Traditional Tone Generators were designed for one primary mission; to identify the termination point of a cable. Unfortunately, these were designed for telephony, not network maintenance.
-
Product
Quadrature Signal Generator
TE5100-PCI
-
The TE5100 is a 100MHz Direct Digital Synthesized Signal Generator available in a 3U, CompactPCI or straight PCI format. The TE5100 generates Sine and ACMOS/TTL output signals simultaneously up to 100MHz in 1 µHz steps. Sweep, FSK, Chirp and Single Tone are generated on board. The virtual panel allows control up to 100MHz of all parameters. The TE5100 is equipped with a ±1ppm on-board TCXO clock and can accept an external clock source.
-
Product
Cable Fault Locator
TX2001
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
Cable Tester/Tracer/Toner, 3-In-1 Professional, Pocket
TCT-700
-
A mult-function test set for RJ-45 LAN cable, BNC and "F" coaxial cable, tone generator, continuity and 6P2C/4P2C jacks. Ideal for electricians, service technicians. telecommunications, networking or general home use.
-
Product
Cable Tester
-
The MapMaster™ mini detects faults and locations of RJ45 network cables. Good terminations, causes of faults and locations of cables are displayed on an LCD display. A set of five mapping remotes is included for locating cables terminated in wall jacks or patch panels. A built-in tone generator with 4 different tone combinations can be used with a tone probe to detect where a cable is routed and the location of the end of the cable.
-
Product
LAN Cable Tester
PA-01D
-
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
Product
Tone Generator with Cable Tracer
1RA470
-
Cable tracer is designed to trace wires without damaging the instalations. It has wolume control to increase sensitivity. Power supply is standard 9V battery.
-
Product
Cable Tracers
180 CB
-
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
Product
Tone Generator
A15TG
-
The Shure A15TG Tone Generator is a battery-powered 700 Hz signal source used to troubleshoot audio systems by checking microphone lines for correct patching and detecting unusual noise that is present. The output level of the A15TG is approximately 42 dBV.
-
Product
Professional Cable Tester/Tracer with Tone Generator
TC-NT2
-
The TC-NT2 is a convenient and comprehensive cable tester for network professionals. Its powerful and user-friendly features enable network installers to accurately check pin configurations of various voice and data communication cables. The TC-NT2 includes a master unit that transmits test signals to its corre-sponding remote terminator to verify cable reliability
-
Product
Variable Tone Generator
-
> 60 Hz to 18 kHz approx> 1.3 VAC P/P> Frequency & Level Pots> Sine or Square Wave> 4.5 x 2.5 x 1.1 inches> 9 volt battery operation
-
Product
VDV MapMaster 3.0 Cable Tester
#T130
-
The VDV MapMaster 3.0 combines continuity testing, mapping, generating tones and length measurement functions into a single easy-to-use unit for installation, troubleshooting, and maintenance for telco, network, or coax cable.
-
Product
LanSeeker Cable Tester
#TP500C
-
The LanSeeker is a fast, rugged cable tester and tone generator in one unit. It displays cable test results using LED indicators on the main and remote unit. An easy-to-use professional grade tool, the LanSeeker is a must have for residential and commercial cable installers. When the unit senses a connection between the main and […]
-
Product
Cable Fault Locator
TX2003
-
6 km (19,000ft) 0.5mtr dead Zone Selectable Cable Impedance Warble Tone Generator Rapid Fault Location Large 128x64 LCD with Backlight Scratch Resistant Display Environmental Protection IP54 CE Approved 3yrs Manufacturers Warranty 60 Hours Battery Life
-
Product
Test Leads
-
Test leads for digital multi-meters (DMM), tone generators, butt sets, oscilloscopes, and other test equipment that uses specialized connectors like Bed of Nails alligator clips, RJ11, sheathed banana plugs, etc. Our cables are similar and replaces genuine manufacturer cables from Fluke, Harris, Tektronix, HP, JDSU etc.
-
Product
Network, Port ID And Cable Tester
One for All PH-400
-
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.
-
Product
LAN CABLE TESTER W/ Tone Generator
PA-01T
-
The LAN Cable Tester with Tone Generator is a perfect companion for any network professional. The tester can enhance one’s ability to quickly locate and verify the status of commonly used voice and data cables.
-
Product
Tone & Probe Kits
-
Triplett Test Equipment & Tools
ProTone Wire Locator Kit features a powerful tone generator and a filtered, ultra-bright lighted probe. The CTX590 functions as a high quality wire locating tool that uses an inductive probe to sense a tone placed on the wires by its associated tone generator. The tone generator provides RJ11, RJ45 and insulated alligator clip connections. The Red/Green LED on the probe indicates continuity, voltage, and polarity. The probe also includes an ultra bright LED tip, fluorescent light noise filter and sensitivity control. The CTX590 can be used for tracking down short circuits, telephone central office connections, and other wire locating applications. Includes (2) 9V batteries and case.
-
Product
Online Audio Frequency Signal Generator
WavTones
-
We are proud to offer not only the best audio frequency signal generator on the net, but also a high-end sound generator, which compares favorably to the more expensive software and hardware tone generators!
-
Product
Tone Amplifier And Tone Generator Set
AM5/TG5xs
-
The New Tone & Amp Set are state of the Art Testers offering touch button technology, visual qTrace (quick trace) as well as audio tracer tone technology providing accurate wire location, high output volume and sensitivity, tone tracker functionality, Visual/Audible indication of Digital Traffic, filtered amplification with multiple volume levels and two normal tones and four tonetracker tones with constant and variable interrupt rates, short detection and indication, capacitive output connection, Quick change battery and low battery indication in New custom designed High impact resistance enclosures, fully sealed to IP67.
-
Product
LANTRACKER
PH-100/120
-
The Lantracker is a network tester, pin-by-pin cable tester, and tone generator all in one. As a network tester, it detects whether a network is active or inactive and displays network speed (10/100/1000 Mbps) in either case. It also flashes the network hub or NIC’s port light corresponding to the cable it is connected to, to show the cable’s port number. As a cable tester, it performs loop-back or remote tests of network, data, voice, and coaxial cables, displaying the results on a pin-by-pin LED display which moves from pin to pin automatically or manually. The Lantracker can be used to test cable or shield integrity, testing network function and speed, and tracing cable using its tone generator function (tone probe not included). Includes an adaptor for testing coaxial-F cable. Uses 1 9V battery.
-
Product
Cable Tester, HDMI Cable, Digital, LAN Tracer, Talk Mode, Tone Generator
TCT-320
-
Designed to check and troubleshoot pin connections of HDMI cables. Tests the continuity of each pin of HDMI cable prior to installation to save time on install.
-
Product
Cable Tracers
181 CB
-
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
Product
ELT STALKER Vector-finder
VF-121
-
The Vector-Finder Types VF-121 and VF 121A are unique in the Vector-finder series of direction finding antennas. They incorporate a proven design, electro statically shielded loop sensing element with modern solid state low noise analog and digital technology to allow detection and location of aircraft band signals. Both the VF-121 and the VF 121A incorporate a unique digital modulator which allows the user to more easily home-in on unmodulated carriers. Such cases occur at airports when transmitter may be accidentally keyed on during aircraft overnight layovers. The VF-121 is specifically designed to be used on airport premises where signal strengths are high. To compensate for very strong signals, an integral attenuator is also incorporated to allow the user to operate the unit close-in to aircraft. The VF-121A differs in that a high gain, low-noise preamplifier is utilized with the sensing element in order to hunt signals that may be weak or at a distance. The unit is ideally suited for the location of ELT transmitters in the field. Both units are tunable over the 118 MHz to 130 MHz aircraft frequencies and interface directly to the user’s aircraft band receiver or transceiver via the antenna jack. With the antenna system connected to the receiver, the user will hear the desired signal. If the signal is unmodulated, the digital modulator will generate a tone on the carrier. When the handheld unit is rotated about, an audible null on the received signal or the generated tone will be heard. This null aligns with the axis of the equipment case and represents the direction of the received signal. This direction may be read from the black dial compass mounted on the top of the enclosure. As the response is bi-directional, triangulation may be used to determine the true bearing when the true direction is not known.
-
Product
Tone Generator
-
Control and test 2-way radio systems, repeaters, ANI, Paging and more. Activate 2-tone or 5/6-tone pagers. Operate or test EIA tone-remote systems. Record generated signals to a WAV file Accomplish MORE, by carrying LESS hardware in the field. Monitor inputs and outputs with our FREE built-in audio scope and spectrum analyzer. No external hardware required. Output may be fed directly into radio, twisted pair, or service monitor.*
-
Product
Continuity Testers
-
Triplett Test Equipment & Tools
Tester performs a TIA568 test on CAT5/6 network cable (RJ45) with instant PASS/FAIL results — opens/shorts, reversals, split pairs, and continuity. It is ruggedized and cushioned for toolbox use with a hidden drawer for remote storage. Includes a built-in tone generator for tracing and troubleshooting.
-
Product
Audio Test Tone Generator
Tone Plug
-
The TONE PLUG offers five user selectable sine wave test tones at frequencies of 100, 250, 400, 1K and 10KHz. An additional 5 special function test signals are also provided.
-
Product
Cable Fault Locator
TX2002
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3500m (11,500ft) 50, 75 & 100 ohm Selectable Cable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
LAN Check With Tone Generator
PH-01
-
The LANCHECK consists of two modular units, a tester and a remote terminator. The modular design enables the tester to be used for local loop-back testing of patch cable or remote testing of pre-installed premise wiring. The LANCHECK makes it easy to recognize opens and shorts within a cable as well as identify reversed and miswired cables. It can verify a cable up to 2,000 feet in length. Furthermore, it comes with shielded connectors, which enables the testing of shielded twisted pair (STP) cables. It also features convenient Auto Scanning and precision Manual Scanning modes.
-
Product
Tone Test Set
240 Weathertite
-
The AINES Model 240 Tone Test Set is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
