USB Test
-
product
USB⇔RS-422/RS-485
SI-35USB
SI-35USB is an USB converter, which converts USB of PC into RS-422/RS-485.
-
product
USB Controlled High Precision Audio Test Interface
AudioConnect 4×4
AudioConnect 4×4 is a high accuracy 4-in, 4-out audio interface specifically audio test and measurement. It offers digital and analog audio in and out at any user-specified sampling rate up to 200kHz, and a high signal to noise ratio and wide frequency response, making it suitable for the most demanding measurement applications. Controls are simple – a single USB connection and a power indicator – all other typical soundcard controls that are not used for audio test applications have been eliminated to make operation and calibration simple with no room for error. AudioConnect 4×4 is supplied fully calibrated.
-
product
Conformance Test System
TS-RRM
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
product
USB 32-Bit Whacker
PIC32MX795 Development Board
The new version of the UBW32 now uses the PIC32MX795 IC. Based on the work of Brian Schmalz, the UBW32 is a small development board for the new PIC32MX795 32-bit CPU from Microchip. The UBW32 is breadboard friendly and includes all of the external circuitry needed to get the PIC32 up and running. Power can be provided over USB or from an external source. It has three push buttons (Reset, and two user-defined buttons) and five LEDs (Power, USB, and three user defined LEDs). All of the 78(!) of the PIC32's I/O pins are broken out. The board comes pre-loaded with a USB bootloader and special UBW firmware that accepts simple serial commands to control the various I/O functions.
-
product
USB Isolators
USB isolators protect the communication interface between the host, such as a PC, and its peripheral. Utilizing iCoupler® digital isolation technology, Analog Devices offers USB 2.0 compliant SOIC components with data rates up to 12 Mbps that provide EMC protection and safety isolation, reduce design size and time, and lower system cost. Galvanically isolated USB μModule® (micromodule) transceivers integrate the USB interface with an isolated dc-to-dc converter for up to 2.5 W of isolated power and provide ±15 kV ESD. Whether for host, hub, bus splitter, or peripheral device, these transparent USB digital isolators are easy to use—they just work—all while meeting the demanding standards required for medical and industrial applications.
-
product
USB Charger
PeakTech Prüf- und Messtechnik GmbH
This practical table power strip offers two safety sockets with child protection and two USB charging ports with a high maximum charging current. There is a shelf for smartphones and tablet PCs on the front, which, thanks to its slightly angled shape, enables excellent usability of the device. The non-slip rubber nubs on the bottom prevent slipping on the work table, with an integrated blue LED as a power indicator.
-
product
PCI Express 5.0 Test Platform
Teledyne LeCroy’s PCI Express 5.0 Test Platform is part of a suite of tools that facilitates complete protocol testing of PCI Express devices up to and including version 5.0. The latest feature of the Teledyne LeCroy Test Platform is the addition of an integrated interposer, which eliminates the need for an external interposer. This innovation simplifies setup with fewer connection points and outboard devices, making analysis easier and more reliable than ever. In addition to using the Test Platform with the Exerciser, the user can connect two of their own devices and use the Test Platform as a PCIe 5.0 backplane and as an interposer to capture protocol traffic between the systems.
-
product
Off-Line Base Test Platform
6TL19
The 6TL19 is a bare half-rack with castors for creating Off-Line, modular, flexible, and reliable Base test platforms. The overall rack capacity is 11U (580mm depth).
-
product
Imperial Test Executive
ITE
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
product
USB Databus Analysers
SOAR Family
With Desktop PC PCI slots rapidly following ISA into the history of computing, we believe that our USB based solutions are an excellent way of protecting your test gear investment from obsolescence.
-
product
USB Spectrum Analyzer
RSA306B
The RSA306B USB spectrum analyzer might be small but it packs a big punch. It’s loaded with features you’d expect from spectrum analyzers twice the size and twice the price. Perfect for everyday tasks.
-
product
RSE Wireless EMC Spurious Emission
TS8996
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
product
IOL & Power Cycling Test Systems
Our IOL & power cycling systems increase measurement quality and throughput and reduce testing costs on an open platform. The focus is on seamless monitoring and precise determination of all parameters of each DUT. In addition, the systems are equipped for the special requirements of wide-bandgap technology.
-
product
USB 3.0 Interface Module
SuperSpeed "USB 3.0 modules" for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the USB 3.0 link untouched.
-
product
I2C Bus Monitor - USB
Model JI-216
The JI-216 I2C Bus Monitor is a low cost, easy-to-use PC hosted instrument specificallydesigned for troubleshooting and debugging I2C networks. The JI-216''s FPGA basedarchitecture provides for the capture and display of all valid or invalid messages and I2Cbus events. Captured I2C messages are available for display in two modes: real-timestreaming, or triggered. These modes provide optimized data display for either hardwareor software development. The SDA/SCL timing display aids in tracking down and solvinghardware timing problems. JI-216''s broad bandwidth (DC 3.4Mbits/s), wide input signalrange (0 15.0V), and variable signal filtering provides flexibility in monitoring a variety ofI2C bus systems. An intuitive Windows application manages instrument setup andcontrol. Communications and unit power is provided via a USB 2.0 link.
-
product
Functional Test System
TS-5040
The Keysight TS-5040 Functional Test System is a cost effective, robust and reliable test system that gives you the lowest cost of ownership. In addition, the open architecture Test Exec SL gives you the flexibility to do just about anything you want.
-
product
USB Modules
The USB DAQ series include various USB I/O modules supporting multifunction industrial USB. They are easy to deploy and install.
-
product
USB Explorer (Two Port)
JT 3705
The JT 3705/USB Explorer is a low-cost two port USB powered boundary-scan controller interface specifically suited for low volume testing and in-system programming of (C)PLDs. Explorer supports two fully-compliant boundary-scan test access ports (TAPs) which can be synchronized for test purposes.
-
product
USB Modular Data Acquisition
The Keysight USB data acquisition (DAQ) family gives you the choice and flexibility to create solutions that evolve and expand according to your changing measurement needs. You can acquire, measure, and analyze data from electrical, mechanical, physical, and acoustical phenomena.
-
product
USB Digital Meters
Klein Tools’ USB testers accurately and reliably measure USB port voltage, current, capacity, energy and resistance simultaneously. As they require no batteries, these tools are easy to keep in a tool bag and quickly pull out anytime a USB port needs to be measured.
-
product
USB MPEG Frame Grabber
2251
MPEG1/2/4 and JPEG capture to USB from an analog video source at D1 resolution Compact form factor for embedded designs 30 fps NTSC, 25 fps PAL Synchronous audio capture from a line level (stereo) input Multiple region motion detection Text overlay (OSD) SDK works with multiple units
-
product
USB Controlled Audio Test Interface
AudioConnect
AudioConnect is a 2-in, 2-out audio interface specifically designed for audio test and measurement. It offers digital and analog audio in and out, a a 44.1kHz/48kHz sampling rate, USB control, and a power indicator; all other typical soundcard controls that are not used for audio test applications have been eliminated. This makes operation and calibration simple with no room for error.
-
product
USB Modular Oscilloscopes
U270xA
Roughly the size of a paperback book, these low-cost USB oscilloscopes make it easy to perform essential measurements — waveforms, voltage, current, resistance, and more. Inject standard or arbitrary waveforms into the systems or devices you’re testing with Keysight USB oscilloscopes.
-
product
USB Interface for 1-2 MIL-STD-1553 Channels
NLINE-U1553
The NLINE-U1553 implements the latest USB 3 SuperSpeed technology for 1-2 dual redundant, independent 1553 channels. Full function capability for Bus Controller (BC), multi-RT (mRT), and Bus Monitor (BM). Also, o-scope signal capture on the first channel to troubleshoot bus signals. All built-in a small, rugged cable assembly that allows the customer to easily connect with standard 1553 jack connectors, or make their own custom cable with a Lemo break-away standard. USB 2 backward compatible (but not recommended – USB 3 offers superior throughput performance).
-
product
Wireless Device Functional Test Reference Solution
The Keysight S8890A Wireless Device Functional Test Reference Solution provides an automation environment which is both simple to use, yet comprehensive and powerful. Based on the Test Automation Platform www.keysight.com/find/TAP, S8890A provides optional instrument driver/plug-ins offering simplified logically grouped control steps. These steps can be sequenced, looped and swept to provide powerful individual test cases or comprehensive sequences. Each driver/plug-in is provided with extensive starter sample test cases which can be modified by Keysight or the end user the UE to be tested. Plug-in options:
-
product
USB 2.0 Protocol Analyzer
Mercury T2
The Mercury T2 is the industry's smallest, most affordable hardware-based USB 2.0 protocol analyzer that combines the defacto standard CATC Trace display with powerful analysis features. The pocket-sized Mercury T2 is bus powered and is controlled using any Windows PC. With comprehensive triggering, the Mercury T2 provides much of the same lab quality protocol analysis capabilities offered in Teledyne LeCroy's top-of-the-line USB analyzers.
-
product
PCB Adapter, Receiver, VTAC, to (2) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) and (4) RJ45 Connectors
510170114
Mates with p/n 510171114.Please note: The RJ45 connectors extend beyond the width of the module. Care should be taken when installing in positions adjacent to other PCBs. Please contact VPC, if further assistance is needed.
-
product
USB Oscilloscope
P9242A Keysight Streamline Series
Compact, faceless, USB oscilloscope using Keysight’s InfiiniVision technology. Available at 500 MHz and 5 GSa/s. Offers a small footprint and mobility.
-
product
USB Vector Network Analyzers
Streamline P937XA
The Keysight compact VNA offers the good performance on key specifications such as dynamic range, measurement speed, trace noise and temperature stability. It utilizes the same measurement science with the trusted Keysight VNAs, you can have consistent measurement results. Measurement speed: 24 msec (201 points, full 2-port cal, 100 kHz IFBW). Dynamic range: >; 114 dB at 9 GHz > 110 dB at 20 GHz (10 Hz IFBW).
-
product
USB Picoammeter
9103
Rugged, portable, affordable, and ASCII programmable, RBD's 9103 USB Picoammeter (ピコアンメータ) measures dual-polarity DC current from picoamps to milliamps. It can be biased with an optional built-in fixed +90V DC bias, or your own low-noise DC power supply.
