Gold Testers
See Also: Gold Test
-
Product
Insulation Testers
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
Insulation testers test for capacitance and current leakage in system cables, generators and motors, high voltage equipment and switchgears.
-
Product
LAN Cable Tester
21-6568-00
-
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus.
-
Product
Electronic Ballast Tester
WT4000
-
• Measure parameter: 1) Input: Vrms, Lrms, W, PF, Hz, Phasic angle, total harmonic and 0-39 component of harmonic. 2) Output: Lamp voltage, Lamp current, Filament current, Guided cathodic current, Lamp power, crest factor and oscillatory frequency, single high frequency analysis. • Startup: Startup lamp voltage, lamp current, filament current, guided cathodic current curve and parameter, preheating time; • Simultaneously display on 8 windows for input and output parameters, convenient for comparison and analysis; • Test preheat energy, filament preheat time. And the parameters changes from 0 to 5s of filament voltage, filament current and filament power; • Up to 1MHz lrms test content to every EB; • Analysis symmetry of high Frequency curve of lout; • 12-bit high-speed A/D, sampling rate up to 10MHz, can easily analyse signal curve of output; • Finish an input and output testing at the same time within 1 minute; • Portable, can test, display, print without computer. Test report include data and curve, comply with international standard; • Communication port for PC, run under Windows98 or Windows2000, English Version available.
-
Product
Insulation Resistance Testers < 1 kV
-
With over twenty 1-kV models to choose from, selecting the proper Megger insulation tester can appear a bewildering task at first. Actually all the process requires is a little organization. All Megger insulation testers perform essentially the same test in fundamentally the same manner - accurately and reliably. Refinements and added features, however, separate one model from another in application and operator appeal.
-
Product
Earbud Function Button Tester
BK2121
-
The BaKo Type BK2121 was developed in response to Apple’s need to maintain quality control in earbuds which contain function controls and an internal microphone, designed to be used with newer IPods. It is a compact, easy to setup, easy to use machine with a short test time that you can use to functionally validate each earbud unit as it comes off the product line.
-
Product
Electrical Safety Tester
JUPITER
-
Multinfunction Multimeter for electrical installation safety testing.
-
Product
Radio Communication Tester
CMP180
-
The R&S®CMP180 radio communication tester is a future-proof, non-signaling testing solution for wireless devices in research and development, validation and production. Together with advanced frequency, bandwidth and RF capabilities, it enables testing of new wireless technologies such as Wi-Fi 6E, Wi-Fi 7, 5G NR FR1 and many more. Additionally, the doubled number of analyzers (2xVSA), generators (2xVSG) and RF ports (2x8) enable simultaneous measurements of technologies and devices in a VSA/VSG single-box tester.
-
Product
Digital RCD Testers
-
Used to detect whether the RCD in the circuit can be triggered normally.
-
Product
Non-Contact Voltage Tester With Wire Stripper
5227
-
Peaceful Thriving Enterprise Co Ltd
This product combines most required tools for an electrician to do the wiring job within the building, which includes screwdriver, non-contact voltage detector, illumination and wire stripper for most type wires.
-
Product
Water Vapor Absorption Tester
DRK854A
-
Shandong Drick Instruments Co., Ltd.
Used to test the water vapor absorption performance of the sample.
-
Product
Bit Error Rate Testers
-
The FarSync BERT Tester provides a comprehensive, simple to use, line testing utility for asynchronous and synchronous lines. Standard BER test patterns are used with real time error counters, user controlled error injection, full line test statistics and APIs.
-
Product
4.25Gbps Electrical & Optical Bit-Error-Rate Tester
OPB4250
-
The OPTELLENT OptoBERT™ OPB4250 is a cost-effective easy-to-use bit-error-rate tester (BERT) for testing Fibre Channel (FC) devices, components, modules and systems in R&D and manufacturing environments as well as field installations of Storage Area Networks (SANs). OPB4250 supports 4GFC, 2GFC and 1GFC. The OPB4250 tester is also ideal for Gigabit Ethernet and Infiniband (2.5G) testing. It incorporates a pattern generator, clock recovery circuits, and a bit-error-ratio analyzer in one compact module that provides optical and electrical interfaces at up to 4.25Gb/s. An intuitive graphical user interface (GUI) enables easy point-and-click operation. The GUI displays error counts, BER, and related statistics.
-
Product
Multi-purpose Textile Flammability Tester
-
TESTEX Testing Equipment Systems Ltd.
Multi-purpose Textile Flammability Tester, to determine the flammability resistance of textile fabrics and for the flammability test of toys and toy material. Multi-purpose Textile Flammability Tester complies with ISO 6940 (1995&2004) / 6941 (1995&2003), ISO 15025, EN71-2, etc. Please contact us for more information about flammability test method.
-
Product
ISO, SWP/HCI, USB Card Tester
Spectro 2
-
# SO/SWP terminal simulator for Smart Card testing# Test Cases for ISO, SWP and HCI# ISO/SWP/HCI/USB trace function for ensuring interoperability between a real Smart Card and a handset
-
Product
Leak and Seal Strength Tester
LSSD-01
-
LSSD-01 Leak and Seal Strength Tester is suitable for the quantitative measurement of sealing strength, heat sealing strength, binding strength, overall sealing performance, pressure resistance strength, cap body connection strength, bursting pressure and shedding strength. It is widely used in the soft package, plastic pilfer-proof caps, flexible pipes, etc.
-
-
Product
Cable Testers
E446
-
Tests 3 pin XLR leads, 2 and 3-pole B-gauge jack leads, RCA (phono) leads, most commonly used fuses, and other continuity paths using test leads supplied. Continuity indication by buzzer.
-
Product
Multifunction Tester
EASYTEST
-
EASYTEST carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
CCTV Monitor Testers
-
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA CCTV Moniter Tester has a built-in high-resolution and wide-size high-definition screen display, automatic video signal detection (AHD / TVI / CVI). The design of the monitor and wristband is ergonomic and convenient to use at any time and place.
-
Product
Other Testers
-
Weshine Electric Manufacturing Co., Ltd
It is one of the important planned performance indexes for oil grade and quality identification. In practical application, theselection of suitable viscosity lubricating oil can ensure the normal and reliable operation of mechanical equipment. Thisinstrument is based on the national standard gb265_ The special testing instrument is designed and manufactured for measuring the kinematic viscosity of liquid petroleum products.
-
Product
Velcro Tape Fatigue Tester
UI-FT35
-
Velcro Tape Fatigue Tester is used to test the velcro tape/ hook and loop fastener to repeated closing fatigue resistance ability. Touch and close fastener repeated closing fatigue test is one of the necessary step for velcro strength test no matter for peel strength or shear.strength
-
Product
Multicore Universal Solderability Tester
MUST System 3
-
The MUST System 3 is the latest technological evolution of the original Multicore Universal Solderability Tester (MUST) that grandfathered all modern solderability test standards. It remains the unquestioned industry benchmark for solderability testing.
-
Product
Primary Current Injection Testers
-
Primary Current Injection Tester is designed for testing protective relay and circuit breakers and also testing the turns ratio of current transformers at high variable currents. A test current is injected into the primary side of a system to determine how the system behaves at particular levels of current. This test makes it possible to determine whether the relay will trip and how long the current needs to flow before the trip is initiated.
-
Product
Battery Impedance Tester
-
TES Electrical Electronic Corp.
Test conditions without shutting down battery.Simultaneously measures battery resistance, Voltage, current, and temperature.Auto-hold and auto-data storage. Comparator Function.Rates conditions as pass, warning, or fail.
-
Product
High Voltage Insulating Tester
-
Suitable for preventive maintenance of gapless arresters.By simply clamping around the ground wire of an arrestor with a clamp CT, it detects leak current and leak current resistance components.
-
Product
AC/DC Leakage Current Tester
228
-
Test for dangerous leakage current with the Simpson Model 228, designed to meet the latest UL, IEC, and ANSI specifications. The 228 detects both AC and DC leakage current and simulates human response at three different levels -- reaction, let-go, and burn hazard. Each Model 228 comes with test leads with alligator clips, manual, and batteries.
-
Product
SD Host Tester / SD / EMMC Analyzer / SD Card Tester
SGDK350A (SD card / eMMC tester)
-
This product is compatible with SD Memory Card Physical Layer Specification Version 3.01. Supports UHS-I interfaces (SDR12,25,50,104,DDR50). There is a SpeedClass measurement mode that measures SpeedClass that supports SDXC, and a simple performance measurement mode that performs sequential / random access to any address. In addition, the SD card access library (for Visual Studio) is open to the public, and any command can be executed on the SD card in any pattern.
-
Product
Flying Probe Tester
Condor MTS 505
-
Primarily the Flying Probe Tester was developed to enable In-Circuit testing (ICT) of prototype PCBs. For testing a new design an existing fixture has to be changed or a new fixture has to be procured. The fixtureless design of the MTS 505 Condor is one of its most attractive properties, where the unnecessary and costly time delays incurred for fixture build or changes can be avoided. It is the ideal platform for testing prototypes.
-
Product
Melt Flow Index Testers
-
Instron® melt flow testers are specifically designed for easy and accurate measuring of Melt Flow Rate (MFR) and Melt Volume Rate (MVR). Our extrusion plastometers range from manual to semi-automated plastic melt flow index testers performing multiple weight tests. All our Melt Flow Index testing equipment meets the latest ASTM and ISO standards.
-
Product
Pin Brinell Tester
-
Newage Testing Instruments, Inc.
The Pin Brinell is a cost effective instrument, which uses a calibrated shear pin to control the amount of load applied. Provides consistent loading regardless of operator. Tests in 100 - 730 equivalent Brinell range.
