ECU Simulation
a virtual Electronic Control Unit (Engine Control Unit) used to validate related dynamic systems.
See Also: ECU, ECU Testing
-
Product
Synchro Simulator
SPA-CASE
Simulator
Computer Conversions Corporation
The Synchro Simulator has two modes of operation: Static and Dynamic. The mode of operation is selected by the position of the mode switch. In the static mode, the thumbwheel switches select the output angle. In the dynamic mode, the speed and direction switches determine the rate and direction of synchro outputs. Self test circuitry continuously monitors and displays the output.
-
Product
PXI Battery Simulator 2.8 Amps
41-753-001
Simulator
The 41-753 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals that can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
PCI Strain Gauge Simulator Card, 6-Channel, 350 Ohm
50-265-016
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PXI RTD Simulator Module 18-Channel PT1000
40-262-002
Simulator
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
Single Stream STANAG3910/EFEX Test And Simulation Module for PCI
APXX3910
Simulator
STANAG3910/EFEX Test and Simulation module for PCI with 1 dual redundant HS/LS channel and onboardFibre Optic Front End (FOFE). Easily select between EFAbus and EFEX modes for Tranche II Eurofighter. The APXX3910 is a functional replacementfor model APX3910.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 16 Channel
41-761-003
Simulator
The 41-761-003 is a low voltage 16-channel output module ideal for simulating theoperation of a thermocouple, also available with 32, 24 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 1 kV Isolation
41-752A-112
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 750 V Isolation
43-752A-003
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, Simplified Current Sink, 750 V Isolation
41-752A-901
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI RTD Simulator Module, 8 Channel, PT500
40-263-402
Simulator
The 40-263-402 is an 8-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, Simplified Current Sink, 750 V Isolation
41-752A-902
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
P104 Synchro/Resolver Simulation Board
73DS2
Simulator
NAI’s 73DS2 is a PC104-compatible Synchro/Resolver Simulation Board with three isolated channels. These channels can incorporate up to three Digital-to-Synchro/Resolver Converters with 1.2 VA drive capability in a stack-through module. With galvanic isolation, one of the outputs can be grounded without affecting performance.
-
Product
PXI Millivolt Thermocouple Simulator Module - 32 Channel
41-760-001
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
PXI Millivolt Thermocouple Simulator Module - 8 Channel
41-760-004
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 26 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
Grid Simulators
Simulator
A grid simulator can be used to simulate the characteristics of low-voltage mains. For this purpose, all voltages and frequencies of the supply networks occurring worldwide can be simulated. Critical states such as short-term voltage dips or voltage peaks (surge/burst) can also be generated.The integrated sequencer function enables the generation of different network parameters, e.g. distorted waveforms and intermediate oscillations. Therefore, grid simulators are well suited for testing conformity to standards and especially for determining the behaviour of electrical equipment in borderline situations. Many European and other international standards are pre-programmed for testing.
-
Product
PXI/PXIe LVDT/RVDT Simulator Module, 4-Banks
41-670-101-AABBCC
Simulator
The 41/43-670-101 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has four banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
Product
PXI/PXIe LVDT/RVDT Simulator Module, 2-Banks
41-670-103-AABBCC
Simulator
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 2 channels of 5 or 6-wire or 4 channels of 4-wire.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
43-752A-913
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI RTD Simulator Module, 24 Channel, PT1000
40-263-003
Simulator
The 40-263-003 is a 24-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 3k
50-265-102
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PXI/PXIe Resolver Simulator Module, 2-Banks
43-670-203-AABBCC
Simulator
The 41/43-670-203 is ideal for the simulation of Resolvers. It has two banks, each capable of simulating the output of a single 5 or 6-wire resolver.
-
Product
PXI/PXIe Resolver Simulator Module, 4-Banks
41-670-201-AABBCC
Simulator
The 41/43-670-201 is ideal for the simulation of Resolvers. It has four banks, each capable of simulating the output of a single 5 or 6-wire resolver.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 2k
50-265-304
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PCI Strain Gauge Simulator Card, 6-Channel, 1k
50-265-206
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PXI Battery Simulator Module
41-750-001
Simulator
The 41-750 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals than can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 32 Channel
41-761-001
Simulator
The 41-761-001 is a low voltage 32-channel output module ideal for simulating theoperation of a thermocouple, also available with 24, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module
41-670-XYZ-AABBCC
Simulator
The 41/43-670 range is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. Available with up to four banks, each bank is capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
Product
PXI Battery Simulator Module, 4-Channel, 5 Amp
41-754-011
Battery Simulator
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
PXI Millivolt Thermocouple Simulator Module - 24 Channel
41-760-002
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel
41-752A-001
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
