Filter Results By:
Products
Applications
Manufacturers
-
product
Portable Bar Code Verifier
Laser Inspector 1000
The L1000 analyzes the essential traditional verification parameters including average bar deviation, quiet zones, encodation check, mod check and ratio where applicable. It also provides the ISO/ANSI method Decodability calculation and percent of decode information. Designed for maximum ease of use, even traditionally hard to verify bar codes such as high density codes with 5 mil (.13mm) X dimensions and codes on irregular, wet, shiny, laminated or moving surfaces are accurately analyzed.
-
product
Conformance Calibration Standard Test Card for ISO/IEC Data Matrix and GS1 DataMatrix Symbol Verifiers
AI-CCS-DM-G Rev A
This precision 2D barcode Conformance Calibration Standard Test Card is the first 2D test card to provide ALL 12 of the Primary Reference Symbols specified by ISO 15426-2 for barcode verifiers. They are sized from 0.5mm to 0.2mm so that all the symbol sizes specified in Annex A.3.1 can be tested. Symbols 1-4 are GS1 DataMatrix symbols, while symbols 5-12 are ISO/IEC Data Matrix symbols consistent with the ISO/IEC 16022 standard. The card also includes four calibrated reflectance patches.
-
product
Analog Output Module
ND-6021
- Voltage Output: 0 to 10 V- Current Output: 0 to 20 mA, 4 to 20 mA- Output Isolation: 5000 VRMS- Resolution: 12-bit resolution- Accuracy: ± 0.1% of FSR (current); ± 0.2% of FSR (voltage)
-
product
8AI Modbus RS-485 Remote I/O
ND-6117
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
product
Low-Cost 16-Bit Multi-Function DAQ Card with 2-CH Encoder Input
PCI-9221
The ADLINK PCI-9221 is a 16-bit high-resolution and low-cost multi-function DAQ card, with 16-CH singleended or 8-CH differential input capable of up to 250 kS/s sampling rate. In addition, the PCI-9221 comes with a 2-CH 16-bit static analog output and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, general-purpose timer/counter, encoder input, and PWM output. The flexible function I/O makes the PCI-9221 the best single-board solution for combined data acquisition and simple motion control functionalities. Ideal for manufacturing, laboratory research, and factory automation, the PCI-9221 comes with all the functions you need at an affordable price.
-
product
USB to RS-422/RS-485 Converter
ND-6530
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
PXIe SSD Storage Unit
DM-4M.2-3U
The Big River™ DM-4M.2-3U PXI Express storage unit provides up to 3.8TB* of M.2 SSD storage capacity. With a PCIe x8 Gen3 host interface, the DM-4M.2 delivers high-speed data rates for sequential writes of 3.25GB/s** and sequential reads of 3.41GB/s** to PXI Express based systems. The single slot design of the DM-4M.2 increases the availability of valuable chassis space, allows for maximum storage flexibility. The DM-4M.2 complies with PCIe Gen3 protocol standards. The product is commonly used in the industrial control, test and measurement fields. The DM-4M.2 operates under Windows, Linux, Unix, Solaris and VxWorks.
-
product
Data Acquisition System
Pixie-16
The Pixie-16 is a data acquisition system for nuclear physics and other applications requiring coincident radiation detection with large number of channels.
-
product
16/32 -CH 16-Bit 250/500 KS/s Multi-Function DAQ Cards with Encoder Input
PCI-9222/9223
The ADLINK PCI-9222/PCI-9223 is a 16-bit, 16/32-CH, 250/500 KS/s high performance DAQ card with 8 different input ranges. It also features 2-CH 16-bit analog outputs capable of a 1 MS/s update rate, 2-CH encoder inputs, and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, high-speed DIO, general-purpose timer/counter, pulse generation, and PWM output. Analog input, analog output, and function I/O at full speed simultaneously, and multiple cards can be synchronized through the SSI (System Synchronization Interface) bus if users need more channels than a single board can provide. Ideal for mixed-signal tests, laboratory research, and factory automation, PCI-9222/PCI-9223 is the best single-board solution on the market providing the best integration capability of multiple tasks with high performance and an affordable price.
-
product
Digital I/O Module
ND-6050
- Interface: RS-485- 7 TTL digital inputs- 8 open collector DO- Output up to 30V, 30mA max. load- Programmable input polarity
-
product
16-CH 16-Bit 250 KS/s Simultaneous Sampling DAQ Cards
PXI-2022
ADLINK"s PXI-2022 is a simultaneous-sampling multi-function DAQ card to meet a wide range of application requirements for PXI bus computers. The device can simultaneously sample 16 AI channels with differential input configurations in order to achieve maximum noise elimination.
-
product
8-CH Isolated Digital Input Module
ND-6052
- Channels: 8 DI. 6 fully independent isolated; 2 isolated with common ground- Isolated Voltage: 5000 VRMS- Programmable input polarity
-
product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function DAQ PCI Express Cards
DAQe-2500 Series
ADLINK DAQe-2500 series are high-speed and high-performance analog output multi-function DAQ PCI EXpress cards. The devices are able to update up to 8-CH, 12-bit analog outputs simultaneously at sustaining 1 MS/s. The reference sources and the output polarities are programmable on per channel basis, combining with the multiplying DAC architecture, ADLINK DAQe-2500 series DAQ cards can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees the CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory.
-
product
64-CH 12/16-Bit Up to 3 MS/s Multi-Function DAQ PCI Express Cards
DAQe-2200 Series
ADLINK DAQe-2200 series are highdensity and high-performance multi-function DAQ PCI Express cards. The devices can sample up to 64 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with high-density analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 32 AI channels in order to achieve maximum noise elimination.
-
product
15-CH Isolated Digital Output Module
ND-6056
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
6U High Performance Data Acquisition subsystem
CPCI-AD320
The CPCI-AD320 module provides a 6U high performance data acquisition subsystem. There are 32 thirty-two 100/200 KSPS ADC’s for maximum performance. Or an opt low cost 16 channel version. The Local DSP can be usedto simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection and gain on a per channel basis. The CPCI-AD8320-6U can also accept external scan and trigger signals from a front panel connector.
-
product
LXI 2.4GHz 50ohm 24x8 Matrix
60-771-002
The 60-771 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 8 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
product
PXI 12-Slot BRIC Matrix, 198x8 2-Pole (9 sub-cards)
40-562B-322-198X8
The 40-562B-322-198X8 is a high density BRIC12 matrix module with a size of 198x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI Single 44 x 4 Matrix 1 Pole Screened
40-523-021-S
The 40-523 module is configured as a 44x4 high density matrix with available reedrelay formats of 1-pole, 2-pole and 1-pole screened. The screened version is suitablefor switching signals up to 50MHz. Model 40-524 is a similar matrix, available insingle pole 46x4 format. Typical applications include signal routing in FunctionalATE and data acquisition systems. These PXI matrix cards are constructed using highreliability Ruthenium Electro-Plated Reed Relays, offering >10e8 operations togive maximum switching confidence with long life and stable contact resistance.
-
product
PXI 12-Slot BRIC Matrix, 588x12 1-Pole (14 sub-cards)
40-558-121-588X12
The 40-558-121-588x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
4-Slot BRIC, 128x8, 1 Pole, PXI Matrix (2 Sub-cards)
40-559-401-128x8
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 116x6, 2 Sub-cards
40-596A-102
The 40-596A-102 is a PXI 1-pole 116x6 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-596A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
PXI 12-Slot BRIC Matrix, 576x8 1-Pole (9 sub-cards)
40-558-121-576X8
The 40-558-121-576x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 8 Slot BRIC 75x16 1-Pole (5 sub-cards)
40-561A-121-75X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
8-Slot BRIC, 384x4, 1 pole, PXI Matrix (3 Sub-cards)
40-559-801-384x4
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 8-slot BRIC Matrix, 384x8, 1 pole (6 Sub-cards)
40-558-801-384x8
The 40-558-801-384x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 4-Slot BRIC Matrix, 552x4, 1-Pole (6 sub-cards)
40-560B-021-552X4
The 40-560B-021-552x4 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
product
PXI BRIC4 FIBO Matrix Dual 93x4 2pin brkout
40-592A-013
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
8-Slot BRIC, 320x8, 1 Pole, PXI Matrix (5 Sub-cards)
40-559-801-320x8
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI/PXIe RF Matrix, 16x8, 150 MHz, 50 Ω, SMB, With Y Loop-thru
40-724-011-L
The 40-724-011-L (PXI) and 42-724-011-L (PXIe) are 16x8 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
