Shielded Box
a space surrounded by an electromagnetic radiation barrier
See Also: Boxes, Faraday Cages, Decade Box, Anechoic Boxes, Black Box, Breakout Boxes, Hot Box, White Box, RF Box, Programmable Resistance Box
-
product
TEST BOX
6280 TB
Standard Electric Works Co., Ltd
● Wide range of operating voltage from AC 210V/50Hz to 250V/50Hz.● For checking AC voltage.● For checking a RCD tester's test current & time in mA(ms).● For checking a loop tester.● For wiring check (Phase, Neutral, Earth).● For checking continuity.● For checking insulation (The maximum is 1.2kV).● For checking UK16th edition.● Safety standard: EN 61010-1 / EN 61326-1
-
product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-ST
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
product
Resistor Calibration Boxes
RCB-3
Standard Electric Works Co., Ltd
● The RCB-3 is used to verify and proof any High Voltage Insulation Testers. It can be utilized to calibrate all High Voltage Insulation Testers very accurately Analogs or Digitals.● Some institutions and large industries requested their own calibrator too, therefore, SEW started manufacturing the RCB for special customers.
-
product
802.11a,b,g RF Shielded Test Enclosure
JRE 0709-A
Containing all the capability of the larger JRE enclosures, the compact 0709-A is ideal for small wireless devices such as; 802.11a,b,g WLAN access points, VoIP devices and other small RF devices. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
product
Medical Box PC With IEC 60601-Compliant NVIDIA IGX Platform
MLB-IGX
- GPU: 2,048-core NVIDIA Ampere architecture with 64 Tensor Cores- CPU: 12-core Arm® Cortex®-A78AE v8.2- Up to 1,705 trillion operations per second of AI performance- NVIDIA® ConnectX®-7 smart network interface card (SmartNIC)- Ten years of NVIDIA® hardware and software support
-
product
Android Box
DVB-S/S2+PVR +Wi-Fi +MULTI CAS + LAN (CC CAMD, NEW CAMD, Twin) ALi3601 Processor, The product supports full HD function, enables high definition and standard definition on DVB- S/S2, and support both MEPG-2 and MPEG4/H.264
-
product
OTDR Launch Cable Box
TM1000
Designed to aid in the testing of fiber optic cable when using an OTDR. The OTDR LaunchFiber box is used with Optical Time Domain Reflectometers (OTDR's) to help minimize the effects of the OTDR's launch pulse onmeasurement uncertainty.
-
product
OBD II Data Link Connector Breakout Box & Diagnostics Software
Mr. BOB DLC
Automotive Diagnostics and Publishing
Mr. BOB DLC OBD II Data Link Connector Breakout Box & Diagnostics Software for Network Waveform Viewing. This OBD2 breakout box with 8 Graphing Meter Scope like channels, is designed for the OBD2 DLC data link connector. Includes OBD II protocols such as PWM, ISO, KWP2000, 9151, J1850, VPW and CAN.
-
product
Small Test Boxes
In today’s environment a small specific test box may be needed to test a component, perform R&D or simply tweak your product. Cuming Lehman Chambers has the ability to custom design and construct a precise test box to meet your specific needs.
-
product
802.11a,b,g Dual RF Shielded Test Enclosure
JRE 0814-2R-A
Containing all the capability of the larger JRE enclosures, the rack mounted 0814-2R-A is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices. Two independent 0814 series enclosures are mounted in one 19 inch rack. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
product
Arduino CAN Shield
IFB-10003-AWP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
DISCRETE TMTC INTERFACE BOX
The Discrete TM/TC Box is a 6U custom 19’’ rack equipment that could be filled with 6U, 4HP plug-ins covering the main ECSS compliant discrete I /Fs. The I/O signals of this box are all arranged in the rear side of the box, keeping clear the front side: in this way no accidental operation could be performed on the box.
-
product
SH68-68-EPM Shielded Cable, 68 D-Type to 68 D-Type, 0.25m
199006-0R25
68-Pin Female to 68-Pin Female, Twisted Pair, Shielded Multifunction Cable - The SH68F-68F-EPM Cable, sometimes referred to as SH68-68-EPM, connects NI DAQ 68-pin devices to 68-pin accessories. The SH68F-68F-EPM Cable has D-type connectors and is offered in different lengths.
-
product
SH68-68R1-EP, Shielded Cable, Right Angle Connector, 1 m
187051-01
68-Pin Female SCSI to 68-Pin Right-Angle Female SCSI, Twisted Pair, Shielded, 1 m Multifunction Cable - The SH68F-68R1F-EP Cable, sometimes referred to as SH68-68R1-EP, connects NI DAQ 68-pin devices to 68-pin accessories. The right-angle connector is useful for small spaces where clearance is limited.
-
product
Breakout Box
T1000-37
T1000-37 breakout box is our most versatile model, using dual 37 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 74 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
product
2 Ft. Shielded Cable For All 5xxx/35xx (68 Pin)
GT95021
2' shielded cable for 5xxx/35xx products (68 Pin)
-
product
6 Ft Shielded Cable For All 5xxx/35xx (68 Pin)
GT95031
6 ft Shielded Cable for all 5xxx/35xx (68 Pin)
-
product
Gold Box Power Supplies (AC-DC)
A broad selection of power supplies offering unusually high performance - many models have regulation of ±0.005%. Electronic current limiting and provision for remote voltage sensing are standard features; overvoltage protection is available as a built-in option. Rugged extruded aluminum cases include threaded mounting holes on bottom, back, and side, permitting mounting in any position.
-
product
ONE BOX
Both the Z and X handheld analyzers run on the same software platform, operating system, have the same user interface, same battery, and same charger making training and operation a breeze. Get them both when you purchase the ONEBOX package.
-
product
Shielded and Unshielded Cable
Teledyne Marine Cable Solutions
Shielding Types• Braided I Served I Spiral• Foil & Hybrid• Vapor Barriers• Copper & Alloys• Conductive & Static Dissipative Tapes• Conductive Fabrics• Tensile Members• RFI & EMI Tapes & Braids (Serveor Interwoven)• Utilizing Flat & Round Copper• Stainless Steel• Bronze• Aramid Fibers & Textile, amongothersConstruction• Multi-conductor, shielded pairs, pairs with steel tubed fiber or copper conductors with fiber optics, coaxial conductors & aramid strength fibers
-
product
Switch Box for Fully Automatic Testing
CP SB1
The switchbox CP SB1 reduces wiring work at power transformers. Thereby, the time needed for testing can be reduced and, at the same time, safety can be significantly increased.
-
product
Shielded Container with GR1 CZT-Based Gamma Radiation Detector
Quant GR1
Quant GR1 is a gamma detector solution for mobile laboratory radionuclide analysis. It is designed for measuring the activity of radionuclides in filters, filter papers, beakers of samples. It comes with an optimised and integrated lead/copper shield that enables operation in both standard and raised backgrounds.
-
product
Shield
Arduino Motor Shield Rev3
The Arduino Motor Shield is based on the L298 (datasheet), which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features. The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board.
-
product
DB37M-DB37F-EP, 37-Pin Shielded Cable - 4 AI, 4 AO, 10 DIO
193737-01
DB37M-DB37F-EP, 37-Pin Shielded Cable - 4 AI, 4 AO, 10 DIO
-
product
X13 GPIB Cable, MicroD25 to Shielded cable/Standard connector, 0.2M
183285-0R2
24-Pin Male/Female GPIB to 25-Pin Male Micro D-SUB GPIB Cable - The 24M-24F-MicroDB25M X13 GPIB Cable, sometimes referred to as the X13 cable, connects your system to GPIB devices or interfaces for instrument control. This standard shielded cable can connect PXI Controllers to instrument control devices and is offered in different lengths.
-
product
POWER INTERFACE BOX
The POWER Box is in charge to provide power supply lines towards the UUT simulating the power distribution unit. The box has been designed to host, in any mixed configuration, two kind of plug in modules:
-
product
Manual Switch Boxes
RTI's manual switch box is a portable and versatile test solution for quick IC electrical verification tests. RTI's 96-pin manual switch boxes integrate with a variety of test configurations that are customized to your test and device needs. It requires no software and connects directly to an external power supply for bias test, and performs quick comparison tests using an A/B relay box.
-
product
X2 GPIB Cable,Double-Shielded,Shielded Plug/Receptacles,1 m
763061-01
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
product
SH96F-96M-5, Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 1 Meter
786341-01
Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 1 Meter
