Pseudo-Random Binary Sequence
is the generated bit stream pattern used to identify bit error rate.
See Also: PRBS
-
Product
BERT Measurement Solutions
-
Bit error rate testers (BERTs) are usually the initial step for communications testing. These instruments generate digital test patterns, typically pseudorandom binary sequences (PRBSs), that drive devices under test (DUTs). Following the transmission of the signal through the link, the receiver in the BERT captures the signal. This setup can be used for multiple testing purposes, such as to evaluate the performance of a transmitter, a receiver, or an optical link.
-
Product
AC-Powered, Phase Sequence Monitor
PAA/PLA
Phase Sequence Monitor
NAI's PAA and PLA are AC-Powered, Phase Sequence Monitors that protect three-phase loads from damage due to phase reversals or phase absence. These sequence monitors are ideally suited for rugged defense and industrial applications.
-
Product
Serial AC Power Sequencer
90-200-001
AC Power Sequencer
Each power outlet can be programmed to switched on in sequence with a specific timing delay. The delay can be staggered to ensure that order dependent systems - like PXI - can be switched on and off in an orderly way with just one operation. A staggered start up also limits the inrush current associated with the powering up of equipment, including earth current inrush, placing less stress on cabling and leakage breakers. Power on or off instructions can be initiated from either the front panel switch or via the serial interface.
-
Product
DC-Powered, Phase Sequence Monitor
PAD/PLD
Phase Sequence Monitor
NAI's PAD and PLD are DC-Powered, Phase Sequence Monitors that protect three-phase loads from damage due to phase reversals or phase absence. These sequence monitors are ideally suited for rugged defense and industrial applications.
-
Product
DC-20GHz Programmable Binary Prescaler
UXC20P
-
The UXC20P is a low noise programmable prescaler featuring either divide-by-2, divide-by-4, or divide-by-8 division ratios. The device features differential inputs and outputs, adjustable output swing, and high input sensitivity. The control inputs are CMOS and LVTTL compatible. The UXC20P is packaged in a 24-pin 4x4mm leadless surface mount package.
-
Product
H2, Binary, Toxic & Flammable Gases
-
Our range of thermal conductivity-based gas analyzers measure and monitor hydrogen and other binary gas streams. The XTC601-EX from Michell Instruments is ideal for measurements in safety critical process applications and meets the requirements of IEC61508 SIL2.
-
Product
Sequence Application Manager
AMFAX SAM
-
We have been building test systems for many years, as a result we find that many of the requirements our customers are looking for are very similar. This may be how a user logs in to the test system or the generation of test reports for example.
-
Product
Capacitors - Binary Chip
-
Macom Technology Solutions Holdings Inc.
MACOM’s BOO and BSP Series Capacitors are designed to facilitate bread-boarding or to use where a trimming capability is required. These devices feature the same dielectric layer and bonding surfaces as our 9000 and 9100 Series chip capacitors. By connecting the pads in parallel, the capacitance values are additive, so many combinations are possible.
-
Product
Sequence Control Valve
Code 200
-
Parker Conflow’s Code 200 is a sequence control valve which switches on electrical equipment by detecting the movement of a conveyor belt in dust suppression applications.
-
Product
H2 and Binary Gas Analyzers
-
PST offer a range of hydrogen (H2) and binary gas analyzers utilising the thermal conductivity property of gases to determine the concentration of a Target Gas (hydrogen for example) within a known Background Gas such as oxygen, nitrogen or argon.
-
Product
Binary to BCD Converter
BAC200
-
Computer Conversions Corporation
The BAC series of Binary to BCD converters will convert binary angle data to 5 digit BCD data scaled in degrees and decimal fractions of degrees. Units with display and/or data outputs are available. Custom scaling of the output to represent actual physical units of measure can be provided easily (i.e.: feet, lbs., meters, mills, etc.)
-
Product
Phase Sequence Indicator
PHS 863
-
Two Functions in one unit including open phase and phase sequence. Large Size alligator clips can easily clip on switch-board terminal. Highly Reliable : Identifies 3 phase sequence and open phase check. Functional design : This model is ideal for installing conveyor lines, pump systems and interconnected drivers. Safety approval : CE marks EN 6101-1 CAT. III. EN 61010-2-031
-
Product
Rad Hard Power Sequencing
-
Renesas' radiation hardened quad power supply sequencers are designed to drive point-of load (POL) regulators that power high performance FPGAs and complex, multi-rail power systems.
-
Product
Task Sequencing and Automated Process Control
T-Zero
-
Command and Control Technologies Inc.
T-Zero is a unique process control program that facilitates automated design and execution of command, control, test, and monitoring activities. It features visualization of the operations process itself coupled with automated coordination of group activities. The software provides a visual, role-based interactive timeline built on the real-time data processing power of the Command and Control Toolkit™ (CCTK). T-Zero is the perfect automation solution for labor -intensive procedural activities: improving process organization, repeatability, and freeing operations staff from tedious task details to focus on strategic operational objectives.
-
Product
Phase Sequence Indicators (Contact Type)
855 PR
-
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Lamps let you determine at-a-glance if phase is open.● Large size alligator clips for easy clipping onto switch-boards terminals.● Checks a wide range of 3-phase power sources.● Special test leads length are available on request.● Push button switch is designed to minimize damage due to negligence.
-
Product
Sequence / Rotation Indicators
-
Phase Sequence and Motor Rotation meter detects live phase and sequence orientation of three phase power sources and industrial equipment conductors to ensure proper installation. Motor rotation function identifies rotational direction of industrial equipment such as motors, compressors and generators. Non-Contact Motor Rotation feature determines rotation of running single-phase and three-phase motors without the use of leads.
-
Product
Phase Sequence Indicators (Contact Type)
ST-850
-
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Lamps let you determine at-a-glance if phase is open.● Large size alligator clips for easy clipping onto switch-boards terminals.● Checks a wide range of 3-phase power sources.● Special test leads length are available on request.● Push button switch is designed to minimize damage due to negligence.
-
Product
Binary to BCD Converter
BAC300
-
Computer Conversions Corporation
The BAC series of Binary to BCD converters will convert binary angle data to 5 digit BCD data scaled in degrees and decimal fractions of degrees. Units with display and/or data outputs are available. Custom scaling of the output to represent actual physical units of measure can be provided easily (i.e.: feet, lbs., meters, mills, etc.) They will also accept encoder outputs and display them at extremely low cost when compared to previous solutions.
-
Product
Analog Sequencers
-
Analog sequencers from Analog Devices integrate accurate comparators with the control functionality of power-on and power-down sequencing for voltage regulator banks. The comparators monitor the regulator voltage outputs and trigger the turn on of next rail in the system after a preconfigured time delay. Some members of this portfolio can be cascaded together, which provides scalable solutions to expand functionality across multiple devices. Our analog sequencers provide an easy to use solution for power sequencing challenges in cellular infrastructure, telecommunication, data communication, and data center applications.
-
Product
Binary BCD Converters
-
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
Product
Non-Contact Type Phase Sequence Indicator
890 PR
-
Standard Electric Works Co., Ltd
● The 890 PR is a Non-Contact phase detector with flashing LEDs and a beeping buzzer to show the detection of AC 3-phase sequence.● Two functions in one unit : open phase and phase sequence detection.● Convenient brightness switch to make the indication visible in dim areas or sunlight.● Back cover magnets which attach the instrument to the AC distribution panel offer easy measurement. ● 3-Phase AC 75 to 1000V is fitted for detection.● Conductor size: 1~35mm● Detect frequency range is from 45 to 65Hz.
-
Product
Phase Sequence Indicators (Contact Type)
863 PR
-
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Neon light indicators.● Large size alligator clips for easy clipping onto switch- boards terminals.● Allows you to check a wide range of 3-phase power sources.● Special test leads length are available on request.
-
Product
Non-Contact Type Phase Sequence Indicator
895 PR
-
Standard Electric Works Co., Ltd
Protection class: IP40. Non-contact detector clips. No metal contact points to advocate greater safety. Two functions in one unit : open phase and phase sequence detection. Designed for checking a wider range of 3-phase power sources. LED display lights with buzzer indicator. Brightness button feature for better visibility in dimly lit areas or sunlight. Magnetic mounting feature.
-
Product
Phase Sequence Tester
TKF-12
-
The TKF-12 tester is a modern high-quality, simple and safe device. However it is recommended to get acquainted with he present manual in order to avoid measuring errors and prevent possible problems related to operation of the meter.
-
Product
Sequence Creation Software for Power Supplies and Electronic Loads
Wavy Series
-
WAVY is sequence creation software that supports the power supplies and electronic loads from KIKUSUI Electronics Corp.
-
Product
Pickering Sequence Manager
-
Pickering Interfaces is delighted to announce the launch of sequencing service offering with all LXI platforms*. This functionality will allow a user to set predefined switch/simulation operations on the 1000+ Pickering PXI switch and instrument cards.
-
Product
Phase Sequence Indicators (Contact Type)
4156 PR
-
Standard Electric Works Co., Ltd
● The 4156 PR is used to identify the leads of a diconnected motor so that when the motor is in true phase sequence, it will run in the desired direction.
-
Product
Point on Wave Synchronous Test Sequencer
-
The Portable Point on Wave Synchronous Test Sequencer is India’s only system that helps in time synchronizing the control signals during short circuit tests performed on medium and high voltage switchgear and control gear.
-
Product
VME Sequencer
SIS3100
-
The SIS3100 was developed as the VME side of our PCI to VME interface. The module is however perfectly suited for other custom applications like a histogramming multiscaler for LIDAR or a generic DSP controlled VME histogrammer .
-
