RF Attenuators
Used to reduce input RF & Microwave power by a fixed ratio – expressed in dB. (www.e-meca.com)
-
Product
RF Over IP
-
Quintech Electronics and Communications Inc.
Digital IF / RF Over IP Solutions.
-
Product
PXI-5651, 3.3 GHz RF Signal Generator
779670-01
Signal Generator
3.3 GHz PXI RF Analog Signal Generator—The PXI‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
-
Product
Solid State RF and Microwave Switches
-
The Solid State RF and Microwave Switches have the following advantages over mechanical switches; long operating life, fast switching time, low power consumption and small size. Mechanical RF and Microwave Switches usually have lower insertion loss, higher isolation and higher RF power handling capability. However, because of the advantages mentioned above, Solid State RF and Microwave Switches are to prefer if very low insertion loss and/or very high isolation is not needed.
-
Product
PXIe-5644, 6 GHz, 80 MHz Bandwidth, RF PXI Vector Signal Transceiver
782376-01
Vector Signal Transceiver
6 GHz, 80 MHz Bandwidth, RF PXI Vector Signal Transceiver—The PXIe‑5644 combines a vector signal generator and vector signal analyzer with FPGA-based real-time signal processing and control into a single device, also known as a VST. Because of this software-designed approach, the PXIe‑5644 features the flexibility of a software defined radio architecture with RF instrument class performance.
-
Product
RF Switching PXI Card
GX6062
Switch Module
The GX6062 is a high-density 6U PXI RF switching card that provides 200MHz bandwidth and multiple switching configurations. The GX6062 has 12 groups of 1 x 4 differential, non-terminated RF multiplexers. The 12 groups can be used to create multiple configurations including: 6 x 1:9, 3 x 1:19, 2 x 1:29, 1 x 1:59, and more. The GX6062 switching card plugs directly into any 6U PXI chassis.
-
-
Product
PXI RF Multiplexer, 5x SP4T, 1.3 GHz 75 Ω, Multiway Connector
40-755-205
Multiplexer Module
The 40-755-205 is a 5xSP4T 75 Ω multiplexer and is part of a range of high density RF multiplexers available in 50 Ω and 75 Ω variants with up to 10xSP4T switches in a single PXI module. They are available with two connector options; SMB that provides a frequency range of 1.8 GHz (50 Ω) / 1.3 GHz (75 Ω), or multiway which limits the bandwidth to 1.3 GHz but offers a high density solution occupying one PXI slot.
-
Product
Handheld RF Spectrum Analyzer With 1MHz To 1.3 Or 2.7GHz Bandwidth Options
PSA Series 3
-
1MHz to 1300MHz or 2700MHz frequency rangeResolution bandwidths of 300Hz to 10MHz 1:3:10-105dBm typical noise floor at -40dBm reference levelMeasurement in dBm or dBμV, mV or μWZero span mode with AM and FM audio demodulationTrace modes of normal, peak hold and trace averageLive, View (copy) and Reference traces in contrasting coloursTwin markers with readout of absolute & difference valuesSmart marker movement with selectable peak trackingFrequency counter with 10Hz ResolutionFrequency presets and independent state storageAuto-find automatically sets sweep parameters for the highest signal foundUnlimited storage for waveforms, set-ups and screensUser assignable file names, file stamping from real-time clockUSB interfaces for Flash drives and PC connectionComprehensive status and context sensitive help screensMore than 3 hours continuous operation from a chargeSmaller and lighter than other spectrum analyzers (weight only 0.58 kg)
-
Product
RF Devices that deliver Comprehensive Solutions for Wireless Systems
-
Sumitomo Electric Industries, Ltd.
GaN HEMTs, GaAs FETs , MMICs, and low-noise HEMT solutions offer high performance and uncompromised reliability for radar, base stations, SATCOM, point to point, and space applications.
-
Product
With CATV RF Input EDFA
HA4600/RF
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/RF series is the narrow-band multiplexing EDFA which suitable with CATV application. This EDFA build-in one unit 1550nm direct modulated CATV transmitter used in inter cutting local VAD service. Build-in WDM multiplexing TX optical signal and External input optical signal of the main road then enter EDFA amplification, to server the local users. In order to avoid TX output optical power and the external input optical power does not fit the main road interfere with each other, the output power of the TX through the build-in VOA, from front panel adjust and set. The whole unit is concision, install and debug convenient. Providing high-quality, low-cost solution for all-optical relay 1550nm optical CATV systems, second-grade service area or administration village inter cut local VAD service.
-
Product
PXI/PXIe RF Multiplexer, Single 6-Channel, Terminated, 8GHz, 50Ω, SMA
40-881B-001
Multiplexer Module
The 40-881B-001 (PXI) and 42-881B-001 (PXIe) are single 6 to 1 50Ω RF multiplexers with 8GHz bandwidth and automatic termination of unused signal channels. It is available as a single or dual MUX in one and two slots respectively.
-
Product
PXI Expandable 16x16 RF Matrix 75Ohm Type 43
45-720A-711
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
PXI 16x2 RF Matrix 300MHz 50 SMB
40-728-001
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 50Ω, MCX
40-872A-101
Multiplexer Module
The 40-872A-101 (PXI) and 42-872A-101 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40/42-872A has been minimized by careful attention to the mechanical and electrical design.
-
Product
RF & Telecom
-
The new generation of RF PXI instruments from NI and Keysights provides speed, accuracy and flexibility similar or better than rack and stack instruments, but for a lower cost. NI LabVIEW coupled with PXI hardware provides the latest PC buses, processor’s speed and optional FPGA technology, to the most demanding R&D projects or mass production lines.
-
Product
RF Directional Coupler Elements
87000 Series
-
The Coaxial Dynamics 87000 series X-Tractors are directional RF Signal Sampler Elements designed to permit easy coupling into a coaxial line for counting of frequency, spectrum analysis or scope display.
-
Product
MS-M Style 3-Pin RF Cable Assembly, Female To Unterminated, 2m, RG178 Cable
40-979A-503-2m-FU
-
This 2m long MS-M style RF 3-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with FEP insulation and an attenuation of 102dB/100m at 500MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
Product
RF Shielded Test Enclosure
JRE 0814
-
Testing tall devices? The 0814 stands up to any test up to 18 GHz! Featuring a wide swing open door with durable latch handle, this enclosure finds wide use in the WiFi test environment. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
Product
PXIe-2790, 6 GHz, Dual 2x1 PXI RF Multiplexer Switch Module
782576-01
Multiplexer Module
PXIe, 6 GHz, Dual 2x1 PXI RF Multiplexer Switch Module—The PXIe‑2790 can either switch or combine RF signals for multi-DUT cellular and wireless connectivity production test. It features high-performance solid-state relays that offer unique benefits such as an unlimited mechanical lifetime and fast switching time, as well as front-mounted SMA connectors that provide easy connection to your RF devices.
-
Product
RF Power Monitors
-
Standard connectors: RF In / Out - N-Female, UHF optional. Sampling Ports - RCA-Female, BNC optional.
-
Product
PXI Dual 4 to 1 Terminated RF Multiplexer 3GHz 50 Ohm MCX
40-873-102
Multiplexer Module
The 40-873-102 is a 4 to 1 RF MUX with 2 banks in a single PXI slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
Product
3GHz RF Analog Signal Generator Module
LS3081D
Signal Generator
The LS3081D, 3GHz Single Channel RF Analog Signal Generator, offers industry leading performance, combined with a compact small footprint form factor. The LS3081D features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS3081D was designed to offer excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
Product
RF Shielded Box
TS7124
-
R&S®TS7124 RF shielded boxes enable reliable and reproducible measurements in shielded test environments. The R&S®TS7124 shielded box provides high shielding effectiveness, a good antenna coupling factor and a rugged mechanical design for reproducible results. RF test boxes have been designed not only for product designers or product optimization but also for production lines of wireless devices under test. The soft close feature makes the shielded box safer to operate.
-
Product
RF Signal Generators
-
The RF signal source mainly acts as a stable local oscillator signal in the test, or generates various types of modulated signals, and the two-tone signal is used for signal excitation, receiving sensitivity testing and other applications. When choosing the RF signal source, the frequency range of the signal output, power requirement size, modulation type, frequency stability, amplitude accuracy and many other factors needs to be considered.
-
Product
Single 8 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-763A-001
Multiplexer Module
The 40-763A-001 terminated single 8 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated, 8GHz, 50Ω, SMA
40-882B-001
Multiplexer Module
The 40-882B-001 (PXI) and 42-882B-001 (PXIe) are single 50Ω 4 to 1 RF multiplexers with 8GHz bandwidth. The 40/42-882B range has automatic termination of unused signals and is available as a single MUX in one slot, a dual MUX in two slots, or triple and quad MUXs in three slots.
-
Product
Digital Step Attenuators (DSA)
-
High linearity, fast switching time with broad bandwidth. Best-in-class attenuation error with fine attenuation steps. Most robust ESD protection available.
-
Product
2 GHz Dual 1:4 RF Mux, 50 Ohm Module for DAQ970A and DAQ973A
DAQM905A
Multiplexer Module
2 GHz Dual 1:4 RF Mux, 50 Ohm Module. Direct connection to SMB inputs with 2 GHz usable bandwidth.
-
Product
PXI/PXIe RF Multiplexer, Dual 8-Channel, 3GHz, 50Ω, SMB
40-874A-002
Multiplexer Module
The 40-874A-002 (PXI) and 42-874A-002 are 50 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
