-
product
Visual Fault Locator
OrienTek Optical Technology Ltd.
powerful, mini visual laser source for fiber fault locating. It has attractive design and small size and it is easy to operate. ● Bright red laser at 650nm● Pulsed and CW operation● Outpower: 1mw,10mw,20mw,30mw● 2.5mm universal connector● 40 hours of operation(1mW)● Pocket size design● 1.25 mm adapter for LC (optional)
-
product
650nm Visual Fault Locator
Shanghai Baudcom Communication Device Co.,Ltd.
Visual Fault Locator series Visual Fault Locator uses the DFB-LD as the emitting component. Driven by constant current source, the indicator can emit stable red laser.The product can be used to inspect fiber failure when they connect with optical interface and be inserted into single mode or multi mode optical fiber.It is indispensable tool in fiber project constructing, fiber net-work maintaining, optical component manufacture and research.
-
product
Underground Fault Location
Schweitzer Engineering Laboratories, Inc.
Underground faulted circuit indicators identify the faulted cable section without a time-consuming re-fuse and sectionalize process. Applications include subsurface or pad-mounted transformers, switchgear, sectionalizing cabinets, junction boxes, and splices.
-
product
Fault Locator
BIDOYNG
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
product
Cable Fault Locator With Time Domain (Intelligent Bridge)
GT00ZD00ZY
GAOTek Cable Fault Locator with Time Domain has a reflectometer to locate faults in metallic cables and Intelligent bridge for tesing the broken line
-
product
Handheld Cable Fault Locator
TM800H
TM800H Handheld Cable Fault Locator adopts TDR (Time Domain Reflection), new signal process and data collection technology. It can locate the distance of cable break and mix faults accurately. TM800H can be widely used in the communication installation, maintenance and general wiring. It can troubleshoot not only the local Telco-cable, but also Network cable. Its high sampling rate makes the measurement dead zone as narrow as 1 meter. This makes it a straightforward, user-friendly test solution.
-
product
Surge Generator
CFL SG 0810
SCOPE offers CFL SG 0810, Surge Generator with output of 8kV and 1000 Joules. It is ideal choice for fault location on all types of power cables from LV to MV. CFL SG series is equipped with different Protections, Interlocks and Auto-discharge facility to ensure user safety during operation. User friendly controls, adequate form factor, contact free HV terminations makes this CFL SG series most durable and best-designed sets in the segment
-
product
Analyzer System
Ruggedized Test Systems (RTS)
This analyzer is a rugged, field deployable system that detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex.
-
product
Tool, Locator, Mini Coax, 24 AWG Wire
910104128
Used with Crimp Tool p/n# 910101118 to crimp 24-26 AWG wire to mini coax ITA contacts.
-
product
Tool, Locator, Micro Coax, Receiver
910101135
Included with Crimp tool kit p/n 910101132 and kit p/n 910101131.
-
product
Tool, Locator, Thermocouple, ITA
910104135
Used with Crimp Tool p/n # 910101102 to crimp thermocouple ITA contacts.
-
product
Optical Fiber Ranger
TM190
Optical Fiber Ranger TM190 is portable fiber fault locator, it is quickly to detect fault location and type of optical fiber using OTDR element and stronger soft ware analysis tool.
-
-
-
product
Tool, Locator, QuadraPaddle, ITA
910104140
Used with Crimp Tool p/n # 910101103 to crimp QuadraPaddle contacts to 22-28 AWG wire.
-
product
PXI Single Bus 64-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-401
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
PXI 5A Fault Insertion Switch 20-Chan 1-Bus
40-198-001
The 40-198 is a 20 Channel Fault Insertion switch, primarily designed for the simulation of fault conditions in automotive/avionics applications involving the reliability testing of safety critical controllers.
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
42-205-008 (PXIe) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
64-Ch 1-Bus Fault Insertion
YAV91082
64 channels 1 thread 2A 250V 1 Fault Insertion Buses Switching up 60W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Dual Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-202
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
PXI Dual Bus 64-Chan 2A Fault Insertion Switch
40-190B-102
The Dual Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Dual Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-002
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Single Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-101
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A, Hardware Interlock
40-194A-002-HI
The 40-194A-002 is a 7-Channel Fault Insertion switch with hardware interlock and two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
product
Pipeline & Cable Fault Locator
TM2000
TM2000 Pipeline & Cable Fault Locator is designed for the Underground utilities route locating, the depth measuring and disatance tracing.
-
product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
The 40-205-008 (PXI) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
PXI Single Bus 32-Ch 2A Fault Insertion Switch
40-190B-201
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Tool, Locator, TriPaddle, Receiver
910104127
Used with crimp tool part # 910 101 103 to crimp TriPaddle receiver contacts to 20-28 AWG wire. This locator contains an integrated wire stop for consistent contact crimping.
