Amplifiers
increase the amplitude of a signal.
See Also: Amp, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
High Voltage Amplifier
HA-205
-
*2500V/uS Super High Speed Model *170Vp-p (±85V DC) *900mAp-p (±450mA DC) *Bandwidth: 3MHz / 100Vp-p *Gain (AMPL): 0~35 (10 Turn VR+SW) *Microprocess Control Protection
-
Product
Bridge Amplifier
90376
-
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
Product
Broadband Amplifier
BBL200
-
The R&S®BBL200 broadband amplifiers are ideal for applications requiring high RF power.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
4-Channel 200 MHz A/D with 32-Channel DDC with Virtex-6 FPGA - 3U VPX
Model 52662
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- Up to 2 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Shortwave Plus 50 MHz Power Amplifier
OM2000A+
-
Thank you for purchasing this new model of the OM Power’s RF power amplifiers line for HF and 50 MHz amateur radio bands. You now own, the OM2000A+, an automatic unit with no knobs, no rotaryswitches on the front panel, just two small switches and one large touch display.Smart design, modern conception, high reliability is the result of OM Power’s development and many years of experience with overall solutions and special attention with the design of the protection circuits.This product is covered by two years of warranty on the amplifier itself and one year for the tube.We wish you will have many years of trouble-free use of this equipment, lots of fun and successful contacts in the world of amateur radio.
-
Product
GaN Power Amplifiers > 5W
-
Macom Technology Solutions Holdings Inc.
MACOM GaN RF power amplifier solutions are designed with the latest GaN-on-SiC and GaN-on-Si technologies. Our MACOM PURE CARBIDE series of GaN-on-SiC power amplifiers offers high performance and reliability for the most demanding applications. Our expanding GaN portfolio is designed to address the challenging requirements of Aerospace & Defense, Industrial, Scientific and Medical applications and 5G wireless infrastructure. MACOM GaN products deliver output power levels ranging from 2 W to over 7 kW and exhibit best in class RF performance with respect to gain and efficiency. For sensitive Aerospace & Defense applications MACOM can offer a US only supply chain with AS9100D Certification.
-
Product
Lock-in Amplifier
HF2LI
-
The Zurich Instruments HF2LI (high-frequency, 2 inputs) is a digital lock-in amplifier covering the frequency range between DC and 50 MHz. It features 2 physical input channels so that it can replace 2 devices in many measurement setups. The 128-bit digital signal processing delivers superior precision thus boosting both the noise performance and the dynamic reserve. With these unprecedented capabilities, the HF2LI brings lock-in amplification to a new level and enables new applications in a frequency range that was previously tied to analog instrumentation. The computer is connected by a high-speed USB interface, which allows data acquisition at high rates. The HF2LI is delivered with a fully featured graphical user interface and a choice of programming interfaces that greatly add to the usability of the instrument.
-
Product
Free Space Tapered Amplifier
-
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
Product
860MHz CATV Indoor Bi-directional Amplifier
-
Hangzhou Softel Optic Co., Ltd.
SA801H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network.
-
Product
Portable 4-Quadrant Power Amplifier
PIV270
-
PONOVO POWER's PIV270 Power Amplifier is equipped with feature of high power, large current, high voltage, high precision, high speed etc. It can meet different application on power and precision requirements.
-
Product
Wideband Distributed Amplifiers
-
A wideband amplifier has a precise amplification factor over a wide frequency range.
-
Product
Instrumentation (Tacho) Amplifier
MS 2007
-
Instrumentation Amplifier is a customized unit to incorporate additional line filtering and spike suppression so that the amplifiers can operate directly off the main aircraft 28 volt system and amplifies the input signal according dynamic input configuration. This unit is capable of working without damage in both under and over voltage conditions. Designed for general aircraft applications.
-
Product
2-Channel 500 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Bi-Directional Amplifier
-
RF Lambda’s bi-directional amplifiers can be used in repeater type applications where a single conductor is used for both receive and transmit. These amplifiers offer low noise figure and high linearity. Hermetically sealed options are available upon request.
-
Product
RF Amplifier
SA812AGC
-
Hangzhou Softel Optic Co., Ltd.
SA812AGC Field Bidirectional AGC Amplifier is a new high gain amplifier. Adopt optimized circuit design and scientific and rational process. High performance AGC control circuit inside is useful for stable gain and low distortion. It's the best choice for large and medium-sized bidirectional CATV transmission network.
-
Product
RGB Digital Fiber Optic Amplifier
CZ Series
-
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
Product
Dual L-Band RF Tuner and 4-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX
Model 58791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Two programmable LNAs handle L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Four 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Four FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
-
Product
CATV Booster Optical Amplifier
HA5100
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
Product
DT Range Broadband Power Amplifiers 10 KHZ - 1000 MHZ
DT Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 1000 MHzTypical output power : 25 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 20 W and H<-20 dBc up to 450 MHz andP1dB > 10 W and H<-20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Monolithic Balanced Mixers With Intermediate Frequency Amplifier
-
Insight Product Company offers Monolithic Balanced Mixers with and Intermediate Frequency Amplifier in frequency range of 26 to 178 GHz.
-
Product
Broad Band Amplifiers
-
Broad band amplifiers (A.K.A. wide band) from Fairview Microwave provide amplification for radio frequencies in broadband. Our broad band amplifiers applications include: military / defense, test instrumentation, EW/ECM, radar, satcom, telecom, microwave radio and various industrial RF, microwave and millimeter wave applications. Fairview broad band amplifiers have a maximum frequency as high as 18 GHz depending on the amp configuration.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
RF Amplifiers
-
UST specializes in the testing, repair and refurbishment of all types of RF amplifiers (broadband and narrowband), microwave amplifiers and millimeter-wave amplifiers: solid state, thin film, traveling wave tube (TWT), low noise RF amplifiers, intermediate power RF amplifiers, limiting RF amplifiers, doubler RF amplifiers, driver RF amplifiers, variable gain RF amplifiers, and active frequency multipliers.
-
Product
Converter Signal Amplifier – 4…20 mA – DIN Rail
HD978TR3
-
Configurable converter signal amplifier with 4…20 mA (20…4mA). Input range -10 …+60mVdc.
-
Product
C-Band Single Channel Line Amplifier EDFA (SLA)
HSA4200 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4200 series is a line EDFA designed specifically for single wavelength optic transmission system. It is installed in the middle of the transmission line, replacing the traditional relay station, to compensate the optical power loss in the line and extend the signal transmission distance.
-
Product
KW Phase Array Radar Jamming System C, X, Ku, K, Ka And V Band
-
Digital Step Phase Shifter. Digital Step Attenuator. RF Solid State High Power Switch. Front End Low Noise . mplifier for Feedback. Transmit Solid State Power Amplifier Matrix 4x4, 8x8 or 16x16. Ultra Wide Band Flat Panel Antenna. Rotary Joint 360 rotation capability.
-
Product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71620
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Fiber Transmitter With Fiber Amplifier
FTFA 822B - 824B
-
- Work as Transmitter & Fiber Amplifier- AGC - Automatic Gain Control- Built in RF Booster- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lesers with Isolaters- Variable SLOPE Control- Output Wavelength : 1310nmPower Options :- 40V DC- 12V DC / 2 Amp- STB Adapter along with PSP- 7.4V, 2600 mAH Battery
