Filter Results By:
Products
Applications
Manufacturers
-
product
Shock0 to 100g
TGP-0610
The shock logger TGP-0610 measures impacts and can be used for machine condition monitoring and the monitoring of expensive and/or fragile shipments.
-
product
Tensile Strength Tester
Capacity of Tester with accuracy of 100g : 250 Kgf. and 500 Kgf.Capacity of Tester with accuracy of 10g : 20 Kgf, 50 Kgf and 100 KgfS Type Load Cell fixed with Top GripTraverse Speed: 300 & 100mm /min.Grip Separation: 1000 mmGrip Separation: 25 mmTop Grip is fixed and Bottom Grip is Movable Type.Elongation measurement by Steel Scale and Digital Counter Meter Both.Digital Display of Load and Elongation.Peak value of last test can be read.User friendly key panel with switch of zero setting and peak value of last testMotor: 1/2 HP single phase 220V 50 Hz. ( for Capacity up to 100 Kgf )Motor: 1 HP single phase 220 V 50 Hz ( for Capacity up to 500 Kgf)Power: 220 V AC 50 Hz.Safety device by limit switch to protect from over traverse.
-
product
4-Channel Optical Transceiver
QSFP28 AOC
Eoptolink Technology Inc., Ltd.
Eoptolink QSFP28 Active Optical Cable is a 4-channel optical transceiver, which conforms to QSFP28 MSA and works at the rage of 25Gbps per channel. The AOC conforms to transmission speed required by InfiniBand™ EDR, 100 Gigabit Ethernet (100GBASE-SR4) and enables to transmit maximum 100m. Best for close-range high-speed transmission, for example, betweenserver racks, between servers.
-
product
Optical Modulation Analyzer
Signaling has migrated from simple on-off keying to complex modulation formats such as DP-QPSK and PM-16QAM. Advanced test tools are required to test the latest communication systems for 100G, 400G, 1Tb/s and beyond. Tektronix is the only test and measurement vendor that can offer a complete coherent optical test system from signal generation, to modulation, acquisition, and analysis.
-
product
Communication Test Set
Eye-BERT 100G
The Eye-BERT 100G is a low cost, full-featured, stand-alone communication test set with an integrated post equalizer eye opening monitor / scanner. Ultimate flexibility is provided with three different physical interfaces, 13 different configurations, and configurable transmit and receive clocks. The tester supports PRBS patterns up to 263-1 and select data rates from 1.25 to 29Gbps on up to 4 simultaneous channels. Front panel controls are also provided for stand-alone operation. Unlike competing products, fast post equalizer eye monitoring and scanning is included and can be performed on any input channel above 5Gbps.
-
product
Optical tTansceiver Module
QSFP28
Eoptolink Technology Inc., Ltd.
Eoptolink’s EOLQ-851HG-02 QSFP28 SR4 100G Optical transceiver module are designed for use in 100 Gigabit Ethernet links over multimode fiber. They are compliant with the QSFP28 MSA and IEEE 802.3bm 100GBASE-SR4 and CAUI-4. Digital diagnostics functions are available via the I2C interface, as specified by the QSFP28 MSA.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - Brazil 127/220VAC
781630-12
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Portable Data Acquisition & Analysis System
LapCAT III
# 4, 8, or 16 channels# 1 MHz aggregate 12 bit sampling. Resolution is 0.024% of full scale# 13 recording durations, user selected: 132 msec to 1320 sec# Digital Triggering from any channel, with +/- slope or window# 6 full scale gain ranges, user selected: 0.4, 1, 2, 4, 10, and 20 volts full scale - with a 10mV/g accelerometer these equal 40g, 100g, 200g, 400g 1000g and 2000g full scale - higher or lower ranges by different sensor selection
-
product
100 Gigabit Ethernet Rugged Rackmount Recorder
Talon RTR 2757
- Designed for data capture from Pentek Quartz® RFSoC products' 100 Gigabit Ethernet ports- Single QSFP28 port with MPO transceiver- Real-time record rates up to 12.5 GB/s (100 Gigabits/s)- Front-panel removable solid state storage up to 122 TB- Dual Intel Xeon® Gold processors with up to 4 TB of DDR4 SDRAM- 4U 19-inch industrial grade server chassis- Supports up to four independent UDP streams- SystemFlow software GUI with Signal Viewer analysis tool- C-callable API for integration
-
product
Ensenso 3D Cameras
X Series
Imaging Development Systems GmbH
The Ensenso X series is a modular and ultraflexible 3D camera system. The projector module with 100 W LED projector power is equipped with an integrated Gigabit Ethernet switch and can be combined with selected GigE uEye camera models to a customised 3D camera system.
-
product
Portable Test Platform
FTB-4 Pro
The FTB-4 Pro is the latest addition to EXFO’s test orchestration portfolio which transforms business as usual into smarter, scalable network testing that significantly increases operational efficiency and provides vital insights into field operations, network performance and service delivery. The 4 slot modular FTB-4 Pro platform enables a unique combination for 100G commissioning, turn-up and troubleshooting which includes the FTBx-88200NGE 100G Multiservice tester (with iOptics transceiver validation software) and the FTB-5240S-P optical spectrum analyzer. There is no need to carry additional platforms or swap modules for unmatched transport and spectral testing on a single platform that no one in the industry can offer. The versatile FTB-4 Pro platform supports a wide range of modules for field testing, data center interconnect, submarine testing, and lab applications for maximum flexibility and ROI across all phases of the service delivery chain: development, deployment, maintenance and troubleshooting. Module combinations on the FTB-4 Pro can also include iOLM/OTDRs, market leading OLTS for fiber characterization, dispersion solutions and other transport modules all with compatibility with EXFO’s market leading fiber inspection probes.
-
product
TRansceiver Module
CFP2
Eoptolink Technology Inc., Ltd.
Eoptolink CFP2-100GBASE-LR4 / CFP2-100GBASE-ER4 module supports a link length of 10, 20, 25 and 40km kilometers on standard single-mode fiber (SMF, G.652). 100 Gigabit Ethernet signal is carried over four wavelengths. Multiplexing and demultiplexing of the four wavelengths are managed within the device.
-
product
GPIB-ENET/1000 , Ethernet GPIB Instrument Control Device - United States 120VAC
781630-01
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
100G Multimode Fiber Testing and Latency
Fiber Lab MPO
With data centers and other high-speed networks using multimode optical fibers for short distance 100G applications, Fiber Lab MPO is the first solution to provide an efficient approach for
-
product
40-CH 100G Thermal AWG
Flyin’s 40 channel 100G Thermal AWG(100G TAWG) is designed for use within the C -band release of DWDM system. To decrease the power dissipation of the devices in different environmental conditions, the TAWG package is special designed with selection of reliable thermal plastic with low thermal conduction, and the TAWG operating temperature is controlled by using foil resist heater or Peltier TEC with thermistor temperature sensor. Different input and output fibers, such as SM fibers, MM fibers and PM fiber can be selected to meet different applications. We can also offer different product packages, including special metal box and 19” 1U rackmount.
-
product
Quickly & Accurately Validate Any Pluggable Transceiver from 10M to 100G
iOptics
iOptics offers a complete, powerful and easy-to-use tool for CFP and QSFP qualification and can validate the full range of low- to high-rate transceivers including SFP, SFP+, XFP, CFP, CFP2, CFP4, QSFP+ and QSFP28. iOptics offers a faster, streamlined and automated test sequence aimed at quickly and simply validating any type of 10M to 100G interface. It is the ideal solution for multirate field commissioning with a simple one-button pass/fail. It offers automated stress testing for lab qualification and is also ideally suited for data center and data center interconnect (DCI) testing.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device
781630-07
Ethernet GPIB Instrument Control Device - The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Octal Small Form Factor Pluggable Electrical Interface
Eoptolink Technology Inc., Ltd.
Eoptolink is developing OSFP(Octal Small Form Factor Pluggable) a new pluggable form factor with eight high speed electrical lanes that will initially support 400 Gbps (8x50G or 4x100G). It is slightly wider and deeper than the QSFP but it still supports 32 OSFP ports per 1U front panel, enabling 12.8 Tbps per 1U switch lot. OSFP is designed to support the next generation of 800G optics modules that will use eight lanes of 100Gbps, and offers backwards compatibility with 100G QSFP.
-
product
1.6T Optical Receiver Test Application
N4917DJCA
Offers fully automated stress eye calibration and receiver testing for 800G and 1.6T modules with 100G and 200G / λ optical interfaces.
-
product
50/100G PAM4 Pin Photodiodes
Macom Technology Solutions Holdings Inc.
MACOM offers high sensitivity PIN photodiodes with industry leading performance at speeds of 56Gbd / 100G. Proprietary designs enable operation using PAM4 modulation protocols in 50 /100G applications. The high responsivity designs have high reliability and are suitable for use in both tele-communications and datacenter networks. The high bandwidth PIN photodetectors are available in a back illuminated design (highest performance), a front illuminated design (more cost effective) and in both singlet and array form factors
-
product
Optical Clock-Recovery Modules / O-CR
Optical clock-recovery modules are required when a clock signal is not present to trigger the oscilloscope or when it is better to use the embedded clock present in the data stream, such as for 100G Lambda optical signals.Clock-recovery modules are essential for transmitter signal characterization.
-
product
Integrated Optical Modulation Analyzer
N4392A
The new Keysight N4392A is an ultra-compact, portable fully integrated optical modulation analyzer with a 15'' laptop-size screen. It is optimized for daily R&D work and designed for the most affordable performance verification in manufacturing and component test for 40/100G components, modules and systems. It is the first optical modulation analyzer that provides built-in performance verification and recalibration, extending the factory recalibration cycles significantly.
-
product
Rugged Fiber Connectors
TE's ruggedized fiber optics brings the benefits of optical technology to challenging environments providing more bandwidth, more distance, and more performance. Our offering includes Ethernet and other fast communications protocols with the capacity to handle next-generation 40G and 100G when you are ready without the severe distance limitations of copper cables. Optical cables also offer significant size and weight savings to help meet SWaP goals.
-
product
Unmanaged Ethernet Switches
CommFront offers a range of rugged, industrial-grade, managed and unmanaged Ethernet Switches. These Industrial Ethernet Switches have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of 10/100/1000M for both Fast and Gigabit Ethernet networks. In addition, our advanced, rugged, industrial-grade, Fast and Gigabit Ethernet Switches support both point-to-point and multi-drop (daisy-chain or self-healing redundant ring) fiber optic networks, which are designed to cover large areas. These industrial Ethernet Switches support up to 255 fiber nodes, and each fiber node can extend the Fast and Gigabit Ethernet data up to 100 miles or 160 km. When configured as a ring network (managed Ethernet Switches), the built-in self-healing feature allows the Ethernet data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same ring, making the entire Ethernet network more robust and reliable.
-
product
Network Emulator
Netropy® 100G
Developed for the pre-deployment testing and validation of high-speed 100GbE networks, the 100G is capable of precisely emulating 25, 40, 50 and 100Gbps WAN links. It allows service providers and storage system manufacturers to validate how WAN impairments--such as latency, packet loss or congestion--will affect performance over all data center links prior to going to market. Available 1/18
-
product
100G,200G 1X2 DWDM Device (3Ports)
Flyin optronics’ 100GHz/200GHz 1x2 wavelength multiplexer utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add or drop at a ITU wavelength. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
product
Fiber Optic Qualification & Dispersion Test Links
8800 Family
Delaire USA qualification test systems are designed to act as worst-case links for bandwidth/dispersion and attenuation, or to meet the customer's loss, dispersion, and distance requirements for custom applications. Because the test links are constructed from hand-selected, industry-standard fiber and not simulated with dispersion elements, all of the effects including loss, dispersion, and fiber nonlinearities are present and authentic. Typical applications include optical transciever testing and qualification for 40G AND 100G systems
-
product
Ethernet PHY
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of 10G/25G/40G/50G/100G Ethernet Physical Layer (PHY) devices offer unparalleled performance while maintaining high density at low cost. Integrated high-speed, high performance mixed signal I/O using advanced CMOS process nodes support a variety of optical and copper connectivity interfaces allowing the Ethernet PHY product line to span rack and cluster connectivity within the data center, wireless fronthaul, midhual and backhaul connectivity for 5G wireless infrastructure, and seamlessly extend to core networks over DWDM optical links. Advanced features such as in-service eye monitors, traffic monitoring, optical module identification and link training are just a few of the advantages that MACOM’s portfolio provides for end users to leverage for faster bring up, higher reliability and smarter networks.
-
product
Ethernet To Fiber Optic Converters (Multi-Drop)
Our advanced, rugged, industrial-grade, Fast and Gigabit Ethernet to multi-drop fiber optic converters are designed to cover large areas. These converters support up to 255 fiber nodes, and each fiber node can extend the Fast and Gigabit Ethernet data up to 100 miles or 160 km. Depending on the site situation, these multi-drop fiber optic converters can be configured as a daisy-chain or a self-healing redundant ring fiber network. When configured as a ring fiber network, the built-in self-healing feature allows the Ethernet data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same fiber ring, making the entire Ethernet network more robust and reliable. These Fast and Gigabit Ethernet to multi-drop fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - Korea 220VAC
781630-09
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
