-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm
50-293-023
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
EL & VI Tester
REOO RO-EV2400A
-
REOO RO-EV2400A EL & VI Tester is designed for PV module manufacturing lines, enabling fast EL and VI inspection for hidden defects and electrical quality verification.
-
Product
PON Power Meter
PPM-350D
-
The first PON-awareTM power meter to automatically detect and test next-gen and legacy PON technologies. Compatible with GPON and EPON networks (GPON, EPON, XG-PON, XGS-PON, NG-PON2, 10G-EPON). Supports 10G-capable PON networks. Pass-through mode for ONT/ONU verification. Bluetooth and USB connectivity. Supports legacy & next-gen PON technologies, including NG-PON2. Single-layer PON service activation. Multi-layer PON service activation.
-
Product
Bulk Call Generator and network simulator
Emutel Harmony
-
The Emutel Harmony Bulk Call Generator and network simulator is a highly efficient, cost-effective and flexible tool, invaluable for use in the development, performance verification and pre-deployment testing of many types of VoIP, ISDN and analog equipment.
-
Product
Central Office Line Simulator
AI-7280
-
The AI-7280 is a highly flexible central office line simulator. It is designed primarily for the testing and verification of common terminal equipment, including standard telephones, Caller ID devices, SMS (Short Message Service) capable equipment, and any device using an analog Tip/Ring interface circuit. Supplied with the TRsSim software for Windows, it can analyze a telephone''s DTMF characteristics, pulse dialing and flash timing, generate various network tones and ringing patterns. Both Type I (on-hook) and Type II (off-hook) Caller ID is supported using either FSK or DTMF data transmission. As an optional component, the TRsSim software can perform SMS testing to either the ETSI protocol 1 or protocol 2 standards.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm
50-294-034
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Automotive Ethernet Rx Compliance Software
AE6910R
-
Unlike CAN, LIN, or MOST, the IEEE standard for automotive Ethernet demands rigorous compliance verification using specific test cases. The test requirements include complex measurements: vector network analysis with S-parameters, bit error rate (BER) test, and protocol analysis of high-speed digital signals.
-
Product
PCI High Density Resistor Card 18-Channel, 8 Bit, 0 To 255 Ohm
50-295A-121-18/8
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Open Source Immutable Database
immudb
-
- High performance and easy to integrate.- Supports both Key-Value & SQL.- Cryptographical verification, tamper-resistant, and auditable.
-
Product
Infrared Camera for CO Detection and Electrical Inspections
FLIR GF346
-
The FLIR GF346 optical gas imaging camera detects carbon monoxide (CO) and 17 additional gases without the need to interrupt your plant's production process. CO emissions can be a significant threat to primary steel manufacturing operations; even the slightest leak in a vent stack or pipe can have a devastating effect. With the FLIR GF346, inspectors can scan large areas from a safe distance, pinpointing leaks in real-time, reducing repair down-time, and providing repair verification.
-
Product
PCI High Density Resistor Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-295A-021-3/24
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Area Scan 3D Camera
3D-A5000 Series
-
Cognex’s 3D-A5000 series is an area scan 3D camera designed to capture high-resolution 3D images. It features 3D LightBurst technology which rapidly acquires images to maximize throughput. High-resolution 3D images combined with industry-leading Cognex 3D vision tools enable reliable and accurate solutions to applications such as assembly verification, in-line measurement, and robotic guidance.
-
-
Product
Handheld Particle Counters
Models 3888 And 3889
-
Kanomax’s innovative Handheld Particle Counters (Models 3888 & 3889) set the standard of instrumentation in cleanroom / operating room monitoring and verification, filter testing, IAQ investigation, data center cleaning and many more highly specialized and highly sensitive applications. These beautifully engineered devices boast some of the most highly advanced technology in the industry. A combination of accuracy and practicality, these devices count airborne particles with high quality performance.
-
Product
1 Mm Calibration Kit
85059B
-
The Keysight 85059B is a 1.0 mm calibration kit designed for vector network analyzer systems operating over the frequency range of DC to 120 GHz. The opens, shorts and loads in this kit are optimized to provide accurate and traceable calibrations over the specified frequency range. The 85059B with 85059V 1 mm Verification kit are replacements for the 85059A 1 mm calibration/verification kit.
-
Product
Automated Production Testing
-
Automated production testing is critical in today’s competitive manufacturing environment. Companies can no longer rely on variable costs, non-uniformity, and potential health hazards that come with a laborer-based manufacturing line. This is no less true for sound and vibration tests, ranging from in-process burn-in tests to product validation and verification tests.
-
Product
Automated And Connected Mobility Testing
-
The future of mobility will be highly automated. Most new vehicles already feature some sort of assistance systems and rapidly advance into more complex functionalities. But with such technological progress comes increased development effort, complexity, and time-to-market pressures. We offer a great variety of solutions for the calibration, verification, and validation of Advanced Driver Assistance System (ADAS) and Autonomous Driving (AD) features to ensure robustness, reliability, performance quality, safety, and user acceptance.
-
Product
PXI 16 Trib Daisy Chain Switch Balanced 96 W
40-796-001
-
The 40-795/796 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data over 100 or 120 balanced lines.
-
Product
PCI High Density Resistor Card 6-Channel, 24-Bit, 0 To 16M Ohm
50-295A-121-6/24
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Express 5.0 Protocol Exerciser/Analyzer
Summit Z58
-
The Summit Z58 is a PCIe 5.0 protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z58 can emulate PCI Express 5.0 root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
Product
AFDX ® /ARINC664P7 Networks Test, Simulation, Monitoring & Analyzer
ACE-FDX-3U-2
-
AFDX®/ARINC664P7 Test and Simulation module for PCIe x1 with 2 full duplex ports programmable for 10/100/1000 MBit/s. Versions available for both Airbus and Boeing variants of ARINC664P7. Test, verification and simulation of AFDX®/ARINC664P7 End Systems, Switches and Networks. Support for Single or Redundant AFDX®/ARINC664P7 operation. Support for Boeing ARINC664 extensions for EDE at the hardware interface layer.
-
Product
Magneto-Electric Rotation Detector
MP-981/AP-981
-
The MP-981 is a magneto-type detector using a hall element which is suitable for revolution (r/min) measurement from low speed to high speed.Magneto-type detectors use an internal hall element, a permanent magnet, DC amplifier, and voltage regulator and respond to flux, so that a rectangular wave form is derivable from much lower speed all the way though high speed.In addition, a signal indicator is provided in spite of the detector's compact design, making verification of operation and mounting position possible.Meanwhile, the AP-981 is the water and acid proof type, which conforms to Class ' of JIS C0920.
-
Product
Mode-Conditioned Light Sources
-
Thorlabs' Mode-Conditioned Light Sources are fiber-coupled LED sources that have an output with a flat-top profile in the far field. Common applications include the testing of multimode fused fiber components as well as verification of modal behavior in fiber-based setups. Standard fiber-coupled LED sources can have a range of output profiles that are usually not uniform and vary from source to source. This can be dependent on emitter orientation, alignment with fiber tip, and connector assembly. These mode-conditioned sources have been engineered to distribute light evenly into all transverse modes, resulting in an equilibrium modal distribution at the output. The front panel includes an adjustment knob to control the power and an output port that accepts 2.2 mm wide-key FC/PC connectors. A DS15 15 V power supply with a location-specific plug is included with each device.
-
Product
Databus-to-Network Interfaces
OBB2
-
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 4.09k Ohm
40-294-023
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Complete Field Meter Site Testing Solution
7 Series
-
We raised the industry standard by introducing the PowerMaster 7 Series as a true 3-phase analyzing reference standard with internal 3-phase current and voltage source capability. The innovative design of the PowerMaster® 7 Series allows utilities to fully test a metering installation with one piece of equipment. Customer load meter testing, phantom load meter testing, CT burden and ratio testing, CT de-magnetization, PT ratio testing, and transducer testing can all be performed with one solution. In addition, vector diagrams, voltage and current waveforms, and harmonics data up to the 100th harmonic can all be analyzed to complete a true wiring verification.
-
Product
Diagnostic Test Tool
BIRST™ (Built-In Relay Self-Test)
-
Verification and diagnosis of complex switching operation in a test system has always been an issue. BIRST (Built-In-Relay-Self-Test) diagnostic test tool provides a quick and simple way of finding relay failures available on some of our LXI and PXI switch matrices.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 16.3k Ohm With SPDT
50-293-131
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Functional Testing and Test Engineering
-
Customer-supplied or developed in-house• Ruggedization of existing (lab-built) fixtures• Co-develop hardware/software• Deployment, implementation, and training• Engineering evaluation tools• Design verification• Medical device evaluation• Manufacturing test systems• Verification test systems• Go/No-go tests• Serialization, recordkeeping, and datalogging• Troubleshooting failed units with other test platforms
-
Product
Microelectronic Services
-
Services for ASIC houses and Integrated Device Manufacturers are IC Wafer / Final Test, IC assembly, Test Program development, product engineering, Flash / EEPROM programming, characterisation / capability studies, yield enhancement, design verification and failure / yield analysis. Das Test Haus are specialists for wafer test, low power, mixed signal and eeprom test.
