Test System Integrators
-
Product
High Impact Shock Test System
KRD16 series
-
High impact shock test system meets MIL-S-901D standard which covers shock testing requirements for ship board machinery, equipment, systems, and structures, excluding submarine pressure hull penetrations. The purpose of these requirements is to verify the ability of shipboard installations to withstand shock loadings which may be incurred during wartime service due to the effects of nuclear or conventional weapons.
-
-
Product
Gated Integrator | Boxcar Averager
GIA100
-
Artifex Engineering GmbH & Co. KG
The GIA100 gated integrator employs dual monolithic switched integrators. When paired with a photodiode, the boxcar amplifier measures the energy of single optical pulses. The GIA100 design results in very low leakage error, charge injection error and pickup. The precision input stage may be configured for current or voltage inputs.
-
Product
IFE Integrated Power
-
EmPower® IFE Integrated Seat Power Systems are based on the advanced technology created for the EmPower® AC In-Seat Power Systems with smaller volume and higher efficiency than can be found in non-integrated systems. The Seat Power Box (SPB) is designed to provide both 110V AC power for passenger PEDs and DC power for the IFE, USB charging ports, and other in-seat equipment. The SPB is capable of operating in several modes including AC/DC, AC only, or DC only, and provides dynamic power allocation between AC and DC outputs.
-
Product
Tracer Gas Leak Test Systems
-
Tracer gas leak testing is a simple and highly-efficient method of leak detection that provides high sensitivity as well as increased accuracy and repeatability. This method is used for testing parts with very low leak rates that are outside the range for conventional air-flow pressure decay and mass flow, or to replace bubble test methods. Tracer gas testing uses escaping tracer gas to identify micro-leaks in the range of 1x10-4 to 10-9 scc/s.
-
Product
Bluetooth Integrated Stud Detector
MS-B158(7S)
-
*Detect metal > 50mm / Ø25mm iron pipe with auto calibration *Laser line generator / Red straight line *Non-contact ACV detection >100V *Continuity check 0 ~ > 20MΩ *Polarity check 3.0V ~ 24V DC
-
Product
Portable Test System
MT786
-
Actual value, vector, curve displayCurrent and voltage generationerror measurementMeasurement of harmonics up to the 40th
-
Product
Full Wafer Test System
FOX-1P
-
Enables High Throughput, Single Touchdown, Full Wafer Production Testing. Capable of simultaneously testing up to 16,000 die in a single wafer touchdown. Resource configurable up to 16,384 " Universal Channels " - each programmable as anI/O, Clock, Pin Parametric Measurement Unit ( PPMU ) or Device Power Supply ( DPS ). Software-enabled per site flexibility to support small and large device pin count test needs. Comprehensive functional and parametric test capabilities Deep functional pattern data and capture memory optimized for BIST/DFT testing. Per channel PMU for per site parametric testing Individual channel over-current protection to protect wafers and probe cards. Configured for high volume production. Compatible with industry standard probers and probe cards. Available as an integrated test cell with prober, probe cards and 16,384 channel probe I/F. Configurable as a single or dual system integrated test cell.
-
Product
Parametric Test Fixture
U2941A
Test Fixture
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
Product
RF Conducted Immunity Test System
RFCI61000-4-6
-
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
Product
Production – High Speed Functional Test Systems
-
Chroma Systems Solutions, Inc.
Built for production, our high speed functional automated test system is based on our C8000 platform which uses a unique test command optimization technology to prevent sending repetitive control commands to the system hardware devices. This improves system test speed dramatically and, when used with our PowerPro III software, makes it highly efficient as a closed or optimized auto test system.
-
Product
Integrated Leeb Hardness Tester
TIME®510D
-
Beijing TIME High Technology Ltd.
TIME®510D is an updated version of TIME5120 Leeb Hardness Tester, the cheapest and most popular leeb hardness tester manufacturer by TIME. It is portable and integrated with universal impact device D. Compared to TIME5120, the new product offers significant improvements in both outlook and performance.
-
Product
Automated Relay Test System
Relay Master
-
Relay Master is an automatic relay test system capable of testing from one to 64 relays simultaneously without having to remove them from the rack. System automation improves efficiency and reduces track time requirements. The PC-based system stores test parameters and results in a database for ease of reliability and trending analysis.
-
Product
Seat Actuation Systems
System
Extensive solutions for seating cabin interiors including motion and lighting controllers, linear and rotary actuators, power supplies, passenger interfaces, custom harnesses, sensors, pneumatic units, and bladders.
-
Product
Integrating Sphere
-
The simpler way to measure the total luminous flux of lamps and luminaires is to use an integrating sphere photometer system. It is a device to perform spatial integration of flux optically, thus the total luminous flux can be measured with one fixed photometer head and measurement can be instant. An integrating sphere photometer is calibrated with a total luminous flux standard lamp. A test light source is measured by comparison to a standard lamp calibrated for total luminous flux.
-
Product
Three-phase Fully Automatic Test System
TS41
-
Calmet Smart Calibration Devices
The Calmet TS41 test system consists of a three-phase reference meter of accuracy class 0.02% (or 0.04%) and an integrated three-phase current and voltage source up to 3x120A/600V. It makes possible automatic testing of electricity meters in meter test stations
-
-
Product
Integrating Spheres
-
All our spheres can be coupled to our high performance spectroradiometer systems for UV-visible-IR spectral power distribution measurements yielding full colour information including colour rendering indices, chromaticity co-ordinates, colour temperature, etc. Alternatively precision photometric detectors can be fitted for direct total lumen output measurements.
-
Product
Upstream-Measurement-System
AMA 310 UMS & VAROS 107
-
This system combines the KWS devices AMA 310/UMS and VAROS 107 to a high-end monitoring system for the return path frequency range. An AMA 310 in a 19-inch version (3.5 RU) with UMS module is used in the headend, in the field the CATV handheld VAROS 107 is the counterpart.
-
Product
Sensortech Systems
ST-3300
-
Smart RF analyzer, custom-built to your specifications, for process moisture measurement and control of even the most complex products and environments.
-
Product
Laser Test Systems
-
Santa Barbara Infrared, Inc. offers an extensive family of test systems and components that test and characterize the performance of laser range finders, designators, illuminators and spot trackers.
-
Product
Halo Automatic Testing System
-
Our revolutionary Halo system is an automatic metal detector testing device. It is designed to automatically test ferrous, non-ferrous and stainless steel samples on all Fortress metal detectors. Automatic testing saves time, money, labor, along with removing the risk of human error and work place injury at critical control points on a manufacturing line while complying with industry standards. The Halo system is ideal for applications where manual testing of a metal detector is made difficult due to access, position, access to the product flow, environmental conditions, etc.
-
-
Product
Timing Systems
-
ime Codes, generally in serial form, are used to convey time information from one point to another. Many different time code formats have been developed over the years, by both commercial and military agencies. Many of our products support one or more of these time codes as a standard feature.
-
Product
Integrating Sphere Light Sources
-
Integrating sphere light sources with LED based or continuous broadband emission spectrum for use as luminance standards for camera calibration, for the determination of veiling glare, for the adjustment of night vision devices and much more. Diameters in the range from 50 mm to 500 mm with options like monitor detector, signal output control by manual and remote apertures and much more.
-
Product
Mobile Handset Voice Quality Test System
BK9024
-
If you need to test cellphones, the BaKo Type BK9024 is fast and switches between up to 8 phone chambers at once, making it a great choice for quality control on your production line.
-
Product
Optics Test Systems
MTF Measuring Device For Endoscopes
-
Optik Elektronik Gerätetechnik GmbH
Manual MTF measuring device for endoscopes. The measurement setup is based on modular individual components that can be arranged on a breadboard according to the type of endoscope (angle between light entrance and eyepiece).
-
Product
Development System
FE-RE2
-
* Emulates Atmel AT89C51IE2/RE2 and others * 128K Code Memory * Real-Time Emulation * Frequency up to fmax 60 MHz * 3V and 5V Support * ISP and X2 Mode Support * Windows Debugger For C, C++ and Assembler * RS-232 and USB Interface * C Compiler and Assembler
-
Product
METES - Meter Test Systems
-
Dramatic advances in the field of measurement technology and the use of state-of-the-art micro-electronics have led to the development of a new generation of electricity meters which are far more accurate than their predecessors of just a few years ago. As well as measuring the exact amount of energy used, a high level of integration enables electronic meters to perform a number of additional functions. As a result, these meters are also more sensitive to network irregularities. This means that regular testing is the only way to ensure that a meter functions correctly, both during final factory tests and during the entire life span of a meter.
-
Product
Flow Sensor For Compressed Air (FLUEREX With Integrated Display)
PF/PFU
-
This is a flow sensor for compressed air for medium and large flow rates, which is useful for grasping the current state of energy consumption and confirming the effect.
