Meltronics Systemtech
Meltronics Systemtech is a product creation company. As a technology solution provider, we offer services and turnkey solutions in the harsh Real Time and Strategic Electronics Domain spanning many industries like avionics, medical, transport, defence & industrial equipments.
- (080)28525400/01/02
- meltronics@meltronicsgroup.com
- 82, 1st Main, 5th Cross, A Block
AECS Layout
Kundalahalli, Bangalore 560037
India
Categories
-
-
product
Pulse Acquisition Board
MS 1818
*Used to measure the amplitude of discrete pulses driving relay coils/motors*Programmable No. of samples acquisition with programmable trigger option*Converts sine wave to square wave for pulse measurement*Measures amplitude of sine wave*16 Bit ADC interface*16 Bit data bus host interface*FPGA based design with flexible configuration*1K FIFO Storage
-
product
UAV Ground Test Equipment (LTS)
MS 1103
*Checks integrated functionality of UAV*During integration checks it performs the functions of the Ground Control Station*Interface with Target Group Set (TGS)*Information is decoded and displayed in the display panel
-
product
CPCI Or PXI Communication Interface Board
MS 1706
*Memory and IO Read Write Cycles*External Interrupts*32 bit Data Bus*30 bit Address Bus*Control Signals for external interface*Four RS232 PORTS with full handshake signals*Four RS232/RS422 PORTS without handshake signals*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
CAN Controller
MS 1529
- The "CAN" Bus Interface for Hall Controllers and Car controller- On-board EEPROM and KEY inputs for user settings parameters- LCD Module Interface- Eight 110 VDC Opto input interface- Six inputs interface (TINS, TUIB, TDIB, FIRE, FP, PRO-SW)- RS485 Interface and RS232 Interface (Optional)- Real time clock for Time Information
-
product
ARM 9 System on Module
MS 1515
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
product
Data Acquisition & Generator Boards
Meltronics Systemtech Data Acquisition & Generator Boards
-
product
Bus Isolation Board
MS 1705
- Bus Interface - ISA96 Bus, 6U form factor- 16-bit Data Bus- 20-bit Address Bus & Control Signals- Isolated Bus Interface- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
Power Amplifier
MS 2011
Power Amplifier is used to amplify the RF signals from low power to 100 Watts of RF carrier power to 400 Watts Peak envelop power (single side band operation). Outputs are filtered. This system is controlled through microprocessor and it has RS485 interface.
-
product
Antenna Tuning Unit
MS 2012
Antenna Tuning unit is used to automatically tune the notch antenna impedance. Microprocessor does tuning through tuning inbuilt algorithm. It has RS485 interface for external control unit interface. Capacitor unit (CU), Inductor unit, (IU) and RF Element are subunits of this antenna-tuning unit. System maximizes transmission.
-
product
RTM Analog & Discrete Signal Conditioning Board
CPCI Rear IO Analog and Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3663i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector. And Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector
-
product
ECM PCB Tester
MS 1105
*Used for testing of DAWN RWR PCBs in Jaguar Aircraft*19” Rack mountable with built-in wide range of IO signals *Used in 4th line servicing of PCBs*Used in LRU and system level testing*Detects 100% fault coverage including track faults*Adaptability with off-the-shelf instruments
-
product
PCI Analog IO Board
MS 1803
*Bus Interface:- PCI Bus*Analog Inputs:- 16 Single Ended Inputs / 8 Differential Ended Inputs*Input Resolution:- 16 Bits*Input Range:- ±10V*Gain:- Programmable Gain Control (1, 2, 4, 8, 16)*Sampling Rate up to 100Ks/S*Peak Measurement +ve and -ve peak for all input channels
-
product
PCI To CPCI Or PXI Extender Board
MS 1720
PCI to CPCI Extender card is used for extending the standard desktop PCI bus to compatible CPCI bus. This will help to test all the CPCI and PXI cards without having a CPCI or PXI backplane. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the CPCI and PXI boards.
-
product
Break In Break Out Box
MS 3648I
Break in Break Out Box is standard portable 19” rack mountable with 128 Input and 128 Outputs.
