HITEC Sensor Solutions Inc.
HITEC Sensor Developments designs and manufacturers load cells, strain gaged based force and torque sensors, instruments and complete test systems, and is an innovator of custom sensor solutions specific to a customer’s application.
- 978-742-9032
- 978-742-9033
- 10 Elizabeth Drive
Chelmsford, MA 01824
United States of America
-
product
Vehicle Test Sensors
Today's engines contain sensors to tell the vehicle's computer what's going on. Car sensors check for fuel-air mixture, incoming air temperature, wheel speed, and manifold pressure. They then tell your vehicle's computer what to do, based on that information.
-
product
Small Motor Dynamometer
90407
The Model 90407 Conveyor Test Stand by Sensor Developments Inc. is a device used for testing operational parameters of a conveyor motor/roller. The system operates the conveyor motor/roller and performs loading operations, while recording all of the important motor/roller parameters for later analysis.
-
product
PMAC 3000 Process Monitor and Control instrument
90424
The PMAC 3000 is a multi-functional Process Monitor and Control instrument, designed to operate with Sensor Developments Inc. Auto-ID sensors. Model 90424 has been enhanced to support quadrature encoders. This functionality is supported via Auto-ID and third party sensor programming. For easy verification, the encoder version will show the extension “E” when the software version number is displayed at power up.
-
product
Mark II Dual Setpoint Monitor
95006
A patented, precision, solid state motion sensor consisting of a sensing head (encoder) and a master control panel and enclosure, the Mark II features a digital tachometer and a two-set point system. Use of a dual set point system, properly set, assures warning of a potential problem, allowing corrective action before damage can occur, and providing total shutdown if the problem is not corrected.
-
product
Compact Low Profile Load Cell
1000 Series
Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.
-
product
Fail Safe Mechanical Speed Sensor
95004
The Fail-Safe rotary speed control is a fluid/magnet actuated mechanical switch. It incorporates the consistent and dependable forces of gravitation and magnetism to achieve its mechanical switching action. Because the unit requires no electrical power to operate, it can be used in remote areas where access to power supply is inconvenient or unavailable.
-
product
Torque Verification
90229
SDI’s 90229 is designed for calibrating tools used to apply torque including electric and pneumatic power tools, torque sensors, hand and click wrenches. The strain gage based reaction torque sensors in the bench-mount housing remain stationary while torque is applied. The housing dis-assembles by removing two snap pins, allowing the user to easily change socket sizes and capacities.
-
product
Peak Track Instrument
90323
The model 90323 Peak Track Instrument is a general-purpose sensor readout device designed to complement our AutoID line of load cells and torque sensors. AutoID is a term that indicates that the calibration information for a sensor is stored on a chip inside the sensor’s connector. AutoID allows true “plug and play” operation without manual calibration procedures of any kind. The unit is also equipped with a 2-line alpha-numeric display and single button operation for simplicity.
-
product
Digital FM Telemetry
90332
The 90332 digital FM telemetry systems is designed to be used with full-bridge, strain gage sensors. The system features a miniature transmitter powered by a simple 9V battery, and a remote receiver capability of receiving the digital transmission over long distances. The digital technique eliminates many of the problems associated with traditional analog frequency modulated telemetry systems. Improvements with a digital technique include elimination of ripple, temperature drift characteristics, and higher signal resolution.
-
product
Bridge Amplifier
90376
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
product
Force Sensors
Is defined as a transducer that converts an input mechanical force into an electrical output signal. Force Sensors are also commonly known as Force Transducers.
-
product
USB Sensor Link
90386
The 90386 is a portable sensor interface that powers and processes strain gaged based sensor into USB compatible signals. No need for additional signal processing or special PC cards.
-
product
Weld Force Gauges
This system is ideal for field measurement and data logging of forces between the tips of resistance spot welders.
-
product
Mark I Single Setpoint Monitor
The Mark I is a self-contained unit featuring a single set point control. A simple two-step adjustment permits detection of an overspeed and/or underspeed condition at either 10% or 25% of operating RPM.
-
product
Miniature S-Beam Load Cell
500 Series
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
