Pulsar Microwave Corporation
Pulsar Microwave Corporation, established in 1987, is a U.S.-based manufacturer specializing in high-performance RF and microwave passive components spanning DC to 85 GHz. With full in-house design and manufacturing capabilities, we maintain strict control over quality, performance, and lead times, making us a trusted partner for both standard and custom-engineered solutions.
- 973-779-6262
- 973-779-2727
- sales@pulsarmicrowave.com
- 48 Industrial West
Clifton, NJ 07012
United States of America
-
Product
Dual Directional Couplers From 0.5 To 40 GHz
-
Dual directional couplers from Pulsar Microwave are available in standard values of 10, 20 and 30 dB with coupling tolerance of +/- 1.25 dB. They are available in narrowband and wideband designs from 500 MHz to 40 GHz. Most models have a coupling flatness of +/- 0.8 dB. Input Power is rated for 50 watts.
-
Product
SP1T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures pin diode RF switches that are controlled by TTL logic. This configuration is known as single pole, single throw and is often abbreviated SPST or SP1T. They have been engineered to function in 50-ohm systems, and are designed to operate from 40 MHz to 18 GHz. They have a switching time of 100 nanoseconds and input power rating of 200 mW (23 dBm). Performance of 1.6:1 or better VSWR and minimum isolation of 60 dB is typical of most models.All switches of this type require both +5VDC and -5VDC to operate. Typical current consumption is +/- 30 mA. TTL control logic of 0 to +5VDC is required. Units comes standard with SMA connectors.
-
Product
SP2T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
Product
Bi-Phase Modulators To 12 GHz
-
BPSK Modulators modulate an input signal by 0° and 180° phase shifts by injecting a ± 20 mA control signal at port D1.
-
Product
Quad IF Mixers / IQ Demodulators To 16 GHz
-
Quadrature IF Mixers incorporate a 90° hybrid, 2-way 0° divider and two mixers to produce two output signals in phase quadrature (I &Q) when driven by a LO and RF signal.
-
Product
Bias Tees From 0.03 MHz To 85 GHz
-
Pulsar offers a large variety of bias tees that cover frequencies from DC to in both surface mount and connectorized packages. Many models are available with voltages up to 100 volts and currents up to 8 amps and custom requirements are welcomed. Options include higher voltage and current, higher RF input power and a choice of either an RF connector or a feedthrough connection for the DC input port.
-
Product
SP6T RF Pin Diode Switches To 12 GHz
-
The SP6T series of 6-way absorptive and reflective switches manufactured by Pulsar Microwave cover applications from 300 MHz to 12 GHz. They have an isolation of 60 decibels and most models specify 1.6:1 or better return loss throughout frequency band. These 6-way switches require a +/- 5VDC supply to operate. Switching control uses individual 0-5V TTL control logic. Voltage and logic control interfaces into a system using a 9-pin D-SUB connector installed.
-
Product
3-Way Power Dividers From 0.5 To 35 GHz
-
Pulsar Microwave's 3-way power dividers cover 500 MHz to 35 GHz in various connectorized packages. They are rated to handle 30 watts maximum input power for a load VSWR of 1.20:1 or better. The 3-way power combiners are available in both in-line and Tee configurations, and come standard with SMA or N female connectors.
-
Product
DC Blocks From 0.1 MHz To 18 GHz
-
Pulsar Microwave Corporation's DC blocks are designed to inner-only topology and utilize our standard housings for fast turn manufacturing. Designs are tested to 50 Ohms, and models range up to 18 Ghz with a maximum voltage rating of 500 Vdc.
-
-
Product
Single Sideband IQ Modulators To 16 GHz
-
Single Sideband Modulators incorporate a 90° hybrid, 2-way 0° divider and two mixers to produce either an upper (RF + IF) or lower (RF - IF) sideband when driven by a carrier signal and modulation input signal. Depending on the phase relationship of the signals injected into the MOD.I and MOD.Q ports, the modulator will pass either the upper or lower sideband through to the output while rejecting the other.
-
Product
Image Reject Mixers To 16 GHz
-
Image Reject Mixers incorporate a 2-way 0° divider, two 90° hybrids and two mixers. They produce an IF signal when driven by an LO and RF signal while rejecting unwanted sidebands that are very close in frequency.
-
Product
Digital Step Attenuators To 18 GHz
-
This family of digitally controlled switched bit attenuators have standard attenuation ranges of 32 dB and 64 dB, with 8 bits of resolution. LSB of 32 dB models is 0.125 dB, and for 64 dB models LSB is 0.250 dB. Attenuation level is obtained by 8 TTL control inputs.
-
Product
90 Degree Hybrid Couplers To 26.5 GHz
-
Pulsar Microwave manufactures hybrid couplers and dividers from 400 MHz to 26.5 GHz for use in 50-ohm systems. These hybrids are available in narrowband and wideband designs with up to 20:1 bandwidth ratios. Most models are built to handle 100 watts input power. The designs are stripline, and optimized for best matching and isolation performance. Available with SMA or N type female connectors.
-
Product
Low Frequency 3-Way Power Dividers To 1500 MHz
-
Pulsar Microwave manufactures 3-way power dividers from 1 MHz to 1.5 GHz in both surface mount and connectorized packages. They are rated for an input power of 1 watt maximum for a load VSWR of 1.20:1 or better. This series of 3-way power dividers are currently offered in four outline packages. The hermetically sealed outline 301 and surface mount outline B are useful in portable applications where space is premium. Outlines 412 and 433 are connectorized versions in cross or in-line format, respectively.
