Finna Sensors
Finna Sensors is fully dedicated to manufacturing continuous on-line moisture measurement and control systems as well as handheld portable moisture analyzers.
- 909-941-7776
- 909-941-6444
- 9567 Arrow Route Suite #E
Rancho Cucamonga, CA 91730
United States
-
product
Model A8: All-Purpose Moisture Meter
N/A
Designed for flat, curved, smooth, or rough surfaces such as cones or beams of yarn, rolls or stacks of paper or paperboard. Covers 3" a diameter (7.6mm) and penetrates 3/4" (1.9cm). Reliable, long battery life. Includes a rechargeable battery, carrying case, and operating instructions book.
-
product
Model AM-IIIB: Paper Moisture Meter
AM-31B3
Portable digital paper moisture meter to measure single sheets. Permits instant and non-destructive moisture detection measurement on all types of paper and paperboard. Pre-programmed with 11 different Calibration Curved with option to select a field. Fast and accurate. Uses Radio Frequency to minimize effects of pH and temperature variations
-
product
Model LGF2: Gypsum Moisture Meter
MRC006522-2
Two-range version of the Model LFG. Has 1/2 the normal sensitivity, allowing off-scale indications to be accurately read. Includes carrying case, NiMH battery and operating instructions book. Additional details can be found in product link.
-
product
Transverse Planer Moisture System
MC PRO 2400
Maximize grade recovery with Finna Sensors' highly accurate transverse planer meter. The most widely-adopted transverse sensor system acts as a dropout or easily integrates with auto graders. Integration via ProTrac software, with barcode or manual tracking, provides advanced kiln analysis and drying reports.
-
product
Model DG-9 (Universal Voltage)
DA8-G9-UNIV
Designed for semi-solids; powdered, granular or textile materials; and pliable sheets in rolls or stacks. Optional needle electrodes and sensitivity modules which allow for a wide range of moisture measurements. Rechargeable NiMH batteries save hassle and money of battery replacement.
-
product
Handheld Moisture Meters
Since water has a dielectric constant considerable higher than any other material, even a small amount of water in a product will cause the combination dielectric constant to increase substantially. Finna Sensors' capacitance meters can easily recognize this increase in water content and are programmed to display the result in direct reading percent moisture content.
-
product
On-Line Moisture Meters
Many methods are available for measuring moisture content on line, in real time: NIR, RF Capacitance, NMR (Nuclear Magnetic Resonance), and Microwave, among others. Finna Sensors is unique in that it has experience with most of these methods and is therefore able to recommend the best possible solution for any application.
-
product
Model DA-8: Digital Moisture Meter
552210
Provides instant moisture readings from 0% to 25% on a wide variety of materials such as gypsum board, yarn, and more. Stores up to 99 calibrations.
-
product
Model A8-AF: Radome Moisture Meter
MRC005574
Indicates the moisture pockets in aircraft radomes. Two main components include the electrode sensor and the metering unit. Critical to today's sophisticated radar transmissions as poorly monitored moisture levels can degrade radar operation.
-
product
Densigrader: Dynamic Weight Sorter
The Densigrader: Dynamic Weight Sorter is made for on-line mass/density measurements and sorting of green lumber prior to drying. The accurate mass and optional volumetric measurements provide an increase in grade recovery and kiln productivity. Its small footprint fits easily into most transverse, lugged transfer chains. System employs either RS232 or TCP/IP protocols to hand off data to sorting PLC.
-
product
Model V: Veneer Moisture Meter
MRC003304
Calibrated for 48 hard and soft woods in the 0% - 25% moisture range and has dials for specific woods. Accurate to 1/8 inch penetration.
-
product
Model AM-III: Paper Moisture Meter
AM-3003
Portable instrument that permits instantaneous, nondestructive measurement on all types of paper and paperboard. Immediate, accurate readings on moving or stationary rolls, stacks, or reams. Includes a library of frequency and operation modes used to minimize the influence of pH and temperature. Provides greater quality and throughput of product.
-
product
Model L: Lumber Moisture Meter
MRC003303
Calibrated for 77 hard and soft woods in the 0% - 25% moisture range and has dials for specific woods. Accurate to 3/4" penetration. Rechargeable battery.
-
product
Model B: Concrete Moisture Meter
MRC003305
Specifically designed for the concrete block industry. Includes calibrations for over 34 different kinds of concrete block. Direct reading scales for average percent moisture content.
-
product
Model N8: Narrow Materials Moisture Meter
MRC001948
Designed for flat, curved, smooth, or rough surfaces such as cones or beams of yarn, rolls or stacks of cloth, and more. Electrode covers an area of 1 - 1/4 x 3 inches and penetrates 1/2 inch into the product.
