Shenzhen Chuangxin Instruments Co., Ltd.
Shenzhen Chuanxin Instruments Co., LTD, are specialized on our range of special, custom built, test and measuring equipment for product testing as per international norms.
- 86-755-23702758
- 86-755-61577693
- nancy@szcxmi.com
- Xi Xiang Hua Qiao Village
Bao An
Shenzhen,
China
Categories
-
product
IEC60529 IPX9K Waterproof Test Chamber
CX-IPX9
Shenzhen Chuangxin Instruments Co., Ltd.
The main purpose of the equipment is to test product performance of storage, transportation and use in the rain condition.The equipment, mainly used in electronic and electrical products, lamps ,lanterns, electrical cabinets, electrical components, automobiles, motorcycles and their parts etc, tests physical and other related properties of products by simulating the rain condition.After test, judge if the performance of the product meets the demand by verification for product design, improvement, check and factory inspection use.
-
product
2.5mm Test Wire Test Probe Pin
CX-3C
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test wire test probe pin 1.Application: Used to verify the protection of persons against access to hazardous parts. Also used to verify the protection against access with a tool.
-
product
IEC60529 IPX6X Sand Resistance Sand And Dust Chamber
CX-SC800PL
Shenzhen Chuangxin Instruments Co., Ltd.
IPX6X Sand Resistance Sand and Dust Chamber is applied to all mechanic, electric, electronic, electric chemical and mechanical and electric equipments, it is used to evaluate whether equipment can resistivity and storage, running or not in air of dry sand or dust. It is applied to IEC-529, GB4208-93, GB2423.37-89 and GJB150.12.
-
product
Compact Goniophotometer For Lamp Spread Angle Tester
Shenzhen Chuangxin Instruments Co., Ltd.
LCG-1600 Goniophotometrc System carries out measuring methods of fixed location and rotating luminaires. The measured luminaire is installed on the two-dimension rotating table, using “+” laser to make the luminaire lighting center superposed with the rotating center of rotating table. The mechanical equipment allows turning the tested luminaires around a vertical axis and a horizontal axis. When tested luminaires turn around horizontal axis, the detector which is at the same level with rotating table will measure the intensity of each direction at this surface. When rotating with vertical axis, the detector will measure the intensity at the vertical surface. The vertical and horizontal axis can be rotated continuously at ±180° or 0~360°. According to the measurement requirements, the system can be operated in C-γ coordinates. When getting intensity distribution data, computer will calculate other photometric parameters automatically.
-
product
UL94 Combustion Chamber, IE60695vFlammability Tester
CX-S16
Shenzhen Chuangxin Instruments Co., Ltd.
Horizontal Vertical Flame Tester is a comprehensive test instrument whick strickly designed according to Standard IEC60695, GB5169, UL94 and can meet the relative standard's requirements. It's mainly used to test the flammability of plastic and other nonmetalloid parts specimen to evaluate fire hazardous degree of accidental burning caused by the material.
-
product
Digital Spring Tester 30N-500N
HT-30N~500N
Shenzhen Chuangxin Instruments Co., Ltd.
HT Series Digital Spring Tester is a special equipment to test the tensile and compressive deformation and the load of the spring characteristics.
-
product
1KV Insulation Resistance Tester
2680
Shenzhen Chuangxin Instruments Co., Ltd.
1KV insulation resistance tester
-
product
Accessibility Probe
Shenzhen Chuangxin Instruments Co., Ltd.
Temperature test probe surface temperature probe
-
product
IEC60335-2-9 Clause 3 Figure 104 Vessel For Testing Induction Hotplates
CX-104
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-9 clause 3 figure 104 Vessel for testing induction hotplates Parameter : Pot and lid material is mainly Q235, carbon mass fraction <0.08%; 2. The thickness of the wall material is 2 mm;3. The bottom of the pot body can not be outward convex, can not exceed 0.05mm; 4. Pot body and lid surface to be clean 5, size: 110, 145, 180, 220, 300mm each one
-
product
IEC60669 Pendulum Impact Tester
CX-BC2
Shenzhen Chuangxin Instruments Co., Ltd.
This Pendulum Impact Test Device Conforms to the standard GB2099.1, GB16915.1 and IEC60669, IEC60670 standard. To check the impact resistance performance of plug and socket electrical accessory's enclosure.
-
product
IEC60529 IPX5 and IPX6 Hose Nozzle Tester
CX-IPX5/6
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60529 IPX5/6 Nozzle Tester. The interchangeable nozzle assemble easily to the jet handle. The nozzles are made from stainless steel.
-
product
IEC 60068-2-75 IK Pendulum Hammer Impact Striking Element
CX-IKA
Shenzhen Chuangxin Instruments Co., Ltd.
The Pendulum hammer impact strking elements conform to the standard IEC60068-2-75 and IEC62262. It's used for IK07, IK08, IK09 and IK10 ratings.
-
product
Test Finger Nail Probe
CX-75
Shenzhen Chuangxin Instruments Co., Ltd.
The Finger Nail Probe is indicated test IEC60335 and UL requirements. Used to check the security of parts that snap together. The spring gauge assembled in the handle can be calibrated to the neccessary force for using the instrument. This probe is make of stainless steel with appropriated hardened tip and a handle in insulating material. Handle has a special adaptor M5 for use with 50N force gauges.
-
product
GB20550-2013 Fluorescent Lamps Initiator Gauge
CX-YGQ
Shenzhen Chuangxin Instruments Co., Ltd.
GB20550-2013 fluorescent lamps initiator gauge
-
product
30KV-100KV AC/DC Hipot Tester
2674
Shenzhen Chuangxin Instruments Co., Ltd.
30KV-100KV AC/DC Hipot Tester
