ICP DAS USA, Inc.
We seek to provide our customers with cost effective, flexible, and easy to use solutions for their Data Acquisition and Embedded Control Applications.
- 1-888-971-9888
1-346-292-9998 - sales@icpdas-usa.com
- 9804 Whithorn Dr.,
Houston, TX 77095
United States of America
-
Product
CANBus Communication
PISO-CAN400U-D
-
The CAN (Controller Area Network) is a serial communication protocol, and efficiently supports distributed real-time control with a very high level of security. It is an especially suit for networking "intelligent" devices as well as sensors and actuators within a system or sub-system. In CAN networks, there is no addressing of subscribers or stations in the conventional sense, but instead prioritized messages are transmitted. As standalone CAN controller, PISO-CAN400/CAN200 can represents an economic solution of an active CAN board. It has two or four independent CAN bus communication ports with 5-pin screw terminal connector or 9-pin D-sub connector, and has the ability to cover a wide range of CAN applications. Besides, PISO-CAN400/CAN200 uses the new CAN controller Phillips SJA1000T and transceiver 82C250/251, which provide bus arbitration, error detection with auto correction and re-transmission function. It can be installed in a 5V PCI slot and supported truly “Plug & play”.
-
Product
Profibus I/O Expansion Racks
-
PROFIBUS (PROCESS FIELD BUS) is anchored in the international standards IEC 61158 and IEC 61784 is an open, digital communication system with a wide range of applications, particularly in the fields of factory and process automation. It is suitable for both fast, time-critical applications and complex communication tasks.
-
Product
CANBus Communication
PEX-CAN200i-T
-
PEX-CAN200i can represents an economic solution of an active CAN board with express PCI bus. It has 2 independent CAN bus communication ports with 5-pin screw terminal connector or 9-pin D-sub connector, and has the ability to cover a wide range of CAN applications. Besides, PEX-CAN200i uses the new CAN controller Phillips SJA1000T and transceiver 82C250, which provide bus arbitration, error detection with auto correction and re-transmission function.
-
Product
Multi-Port Serial
-
The VXC multi-port serial card enables user to increase additional communication ports on the PC.
-
Product
PCI Express Digital I/O Boards
PEX-P8POR8i
-
PCI Express x1, 8-channel isolated digital input.8-channel PhotoMos Relay output. Includes one CA-4002 D-Sub connector.
-
Product
PCI Daughter Boards
DB-8025
-
Screw terminal board using two 20 pin cable connectorCompatible to 780 series daughter boardDimensions: 114mm x102mm
-
Product
Remote Ethernet Modbus TCP I/O Modules
-
ET-7000 Modbus TCP Remote Ethernet I/O allow configuration, I/O monitoring and control through a regular web browser. Besides Web HMI function, no more programming or HTML skills are required; creating dynamic and attractive web pages for I/O monitoring. They can be easily integrated with SCADA software and other I/O. They come with EZ Data Logger Software for data logging and monitoring systems.
-
Product
PCI Digital I/O Boards
PISO-C64
-
The PISO-C64 has 64-channels of optically isolated digital outputs, arranged into two isolated banks. Each digital output offers a darlington transistor and integral suppression diode for inductive load. Isolated output channels are designed into group C and Group D. The power supply of the input port may use external power or the power from the PC side using DC/DC converter. The power supply of the output port should use external power. This interface board is easily installed in any PC/AT/XT compatible computer. The board interfaces to field logic signals, which eliminates ground-loop problems and isolates the host computer from damaging voltages. The ISO-C64 has one 37-pin D-Sub Connector and one 40-pin male header. Users can connect the digital signal through the second D-Sub connector. Each D-Sub connector contains 32 output channels.
-
Product
Modbus TCP Redundant Ethernet I/O
-
ICP DAS USA's RIO-9380 is a Modbus TCP based Ethernet-based Data Acquisition Rack that supports redundant communication and redundant power for maximum uptime. Our Redundancy Ethernet I/O Racks provide a scalable, open architecture that bridges factory-floor hardware with enterprise IT systems. Designed for mission-critical reliability, these racks support redundant communication paths to ensure the system remains operational during network or power fluctuations..
-
Product
FRnet Controllers
-
FRnet Controllers are the ultimate in Ethernet equipped, high speed digital data acquisition! They offer users a multitude of connectivity and networking options in a compact and robust embedded control format. FRnet technology allows high speed digital data acquisition in the realm of 1Mbps transmission speeds and .7ms scan rates! FRnet controllers are programmable in C Language.
-
Product
Multi-Port Serial
VXC-112iAU
-
The VXC-112 series card provides 2 RS-232 serial ports. It is equipped with a 128-byte hardware FIFO for each port, supports for speed up to 115200 bps and supports full-duplex communication.
-
Product
Board Accessories
ADP-37
-
ICP DAS Industrial I/O boards normally require cables and accessories to complete a package. Please refer to the following items:
-
Product
PCI Daughter Boards
DB-8425
-
Connector interface for PISO-DA2Screw terminals for easy field wiring9-pin D-sub connector pin to pin screw terminal for PISO-DA2
-
Product
Modbus TCP Data Acquisition
-
Modbus TCP based Data Acquisition Modules in a analog and digital I/O configurations including current, voltage, thermistor, thermocouple, RTD, and strain gauge. Some are powered over Ethernet, some have two Ethernet ports and some can send email alarms and trigger outputs based on inputs.
-
Product
Modbus TCP Based Dual Ethernet Port I/O Modules
-
ET-7200 Modbus TCP Based Dual Ethernet Port I/O have 2 Ethernet ports for daisy-chain networking. They are configurable over a standard web browser. Support for Modbus TCP protocol allows easy integration with SCADA software.
